AT&T TCD130040 Guida rapida

TIVO UPGRADE INSTRUCTIONS (#32)

Instructions for SERIES2 TiVo ONE DRIVE REPLACE upgrade

(TCD130040 TCD140060)

These instructions are also available in color online at http://www.weaknees.com

WORDS OF CAUTION:

Upgrading a TiVo presents a few physical hazards. As with most consumer electronics devices, components in the TiVo may still carry a

lethal charge, even after disconnecting from your power supply. Be aware of this while working inside your TiVo. Allow sufficient time

for discharging of components and avoid contact as much as possible with potential hazards. While we have done everything we can to

provide accurate, easy-to-follow instructions, we cannot be responsible for any damage done to your TiVo or to yourself as a result of

your upgrade. By opening your TiVo, you agree that neither Adberg Consulting nor any of its members or affiliates is responsible in any

way for any harm done. Please be VERY careful when upgrading. NEVER open the TiVo while the unit is plugged in and NEVER

operate the TiVo if the lid is not securely fastened. PLEASE NOTE: Opening the TiVo voids the warranty

THIS KIT INCLUDES:

1 T10 Torx L-Key

1 T15 Torx L-Key

1 Upgrade hard drive (not shown)

1 Set of upgrade instructions (not shown)

1. OPENING THE TIVO

Unplug the power cord from your electrical outlet and wait five

minutes for the TiVo to discharge. Do not plug the TiVo back in

until you are completely finished. Be very careful of static

electricity, which can destroy your TiVo’s internal parts. You

should not perform this upgrade on carpet.

Using the Torx T10 (smaller of the two) L-key included with

your kit, unscrew the four Torx screws on the back of your TiVo.

The four screws are surrounded by black from the top of the

TiVo’s case.

Once the four screws are removed, remove the lid. Place your

palms on the top side edges of the TiVo, toward the back and

push toward the back of the TiVo (this occasionally requires a bit

of force). The cover should slide back and then up. Remove the

cover from the TiVo.

2. DISCONNECTING THE DRIVE BAY

Place the TiVo lid upright in front of the TiVo, forming

a platform that will be used to support the drive bay

after you remove it.

With the cover off and looking underneath the front lip

of the TiVo, you will be able to see (1) a multi-colored

(red, black, yellow) power cable that runs from the

power supply to the hard drive, (2) a gray IDE ribbon

cable that runs from the greenish motherboard

underneath the drive to the hard drive, (3) one hard

drive, and (4) a fan cable (two-wires; red/blue) that runs

from the hard drive bay to the motherboard..

Gently remove the fan cable from the

motherboard. Pull straight up and out.

Using your Torx T15 L-key (larger of the two, although

either may work for these screws), unscrew and remove

the two screws on the left-hand side of the drive bay (as

you are looking at the front of the TiVo). Also remove

the gold inserts from the blue grommets and keep the

two screws inside the gold-colored inserts. [In the

picture at the right, the front of the TiVo is to the left.]

Once the screws and inserts are removed, you will be

able to lift the drive bay up from the left side (as you are

looking at the front of the TiVo) and slide it out of the

two holes on the right side of the drive bay. As you

slide the drive bay up and out of the TiVo, do two things

simultaneously (1) support the right side of the bracket

to prevent it from falling onto the motherboard as you

pull it out of the holes, and (2) be mindful of the drive

cable and power cable that are still connected to the

drive. Flip the drive bay up and out of the TiVo and

onto the TiVo lid, with the hard drive face-down on the

TiVo lid and the two cables running from the drive to

the TiVo.

You will now need to remove both of the cables

connected to the hard drive by following the instructions

below:

The hard drive has a power connector running into the

hard drive. The power cable has a white connector

plugged into the hard drive. Remove the power

connector from the hard drive. The power cables are

sometimes difficult to remove; patience and wiggling it

back and forth usually does the trick.

Remove the hard drive ribbon cable (longer, gray cable

with a blue or black connector) from the hard drive by

pulling on the hard plastic piece connected to the hard

drive.

3. REMOVING THE EXISTING DRIVE

Before removing the factory drive, take note of its position on the

drive bay. Your new drive will be installed in the identical

location and position.

With the hard drive bay upside-down on the TiVo lid, use your

Torx T15 L-key to remove the four screws connecting the hard

drive to the hard drive bay. Set these screws aside, and do not

confuse them with the four screws you removed from the back of

the TiVo before removing the lid. Remove the hard drive and set

it aside for safe keeping.

4. CONNECTING THE NEW HARD DRIVE TO THE DRIVE BAY

Align the new hard drive included in your kit on the drive bay, in

the same position as the drive that you removed. Using the drive

screws you removed from the factory drive, attach the drive to

the bracket by following the instructions below:

We have found that the easiest way to attach the drive to the

bracket is to turn the bracket upside down. Using one hand, hold

the drive against the bottom of the bracket and look through the

holes in the drive bay to align the screw holes. Using your hands,

screw the screws into each of the four holes. Use your Torx T15

L-key to tighten the screws. NOTE: Do NOT change the jumper

on your upgrade drive. It is set correctly.

5. CONNECTING THE POWER AND HARD DRIVE CABLES TO THE DRIVES

Connect the gray IDE ribbon cable to the hard drive. If the drive

is face down on the TiVo lid, then the notch in the cable should

be face down as it is inserted into the drive. Be sure the cable is

pushed snugly into the drive (it only fits one way). Be very

careful not to bend any of the hard drive pins.

Connect the power connector to the drive, being sure to align the

power connectors properly. If the hard drive is face-down on the

TiVo lid, then the rounded side of the power cable will also be

down. Be sure that the power connector is securely fastened.

6. RE-ATTACHING THE DRIVE BAY

Now, carefully flip the drive bay over. You will need to insert

the two pins on the right into the light blue grommets, while at

the same time watching the power connectors and the gray hard

drive cable. You will want to tuck the power cables down into

the TiVo (in front of the hard drives). You will also want to

watch the fan cable (the lone red/blue cable) to be sure that it

hangs free.

Once the two pins are in the blue grommets, align the left

side of the drive bay so that it is directly over the screw

holes on the left side of the TiVo.

Screw the two screws (and gold inserts) back into the holes

on the left side of the drive bay using the Torx T15 L-key.

Insert the fan cable back into the

motherboard. (This is easy to forget,

which is why it is in bold!)

7. RE-ATTACHING THE TIVO LID

Kneel down in front of your TiVo as you did when you removed

the lid. Place the TiVo lid back over the TiVo. Align the clips

on each side of the lid so that they clip down on the sides of your

TiVo. Slide the lid toward you while simultaneously pushing

down on the top of the lid. Once the lid is in place, reattach the

four Torx screws using your T10 L-key.

Reconnect your TiVo to your television and power it on. After

your have gone through guided setup, you will be able to verify

your TiVo's new capacity in the System Information screen.

ENJOY! We thank you very much for your purchase and hope that you enjoy your newly-upgraded TiVo. Please

email us with any comments, suggestions or complaints. If you found the upgrade easy to install (or even if you

found it more difficult than you expected), we’d love to know. If you found our service to be excellent (or awful),

we want to know that too. We’re always looking to improve our products and services…the more we hear from

you, the better. Thanks very much!

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali AT&T Registratore vocale

AT&T

AT&T Digital Announcer Guida rapida

Manuali Registratore vocale popolari di altre marche

Sony

Sony ICD-UX533F Manuale utente

RCA

RCA VR5230 Manuale utente

Ramsey Electronics

Ramsey Electronics BULLSHOOTER ENDLESS LOOP BS2C Guida utente

Sony

Sony TCM-400DV Manuale utente

LogTag

LogTag TREL30-16 Manuale utente

SVAT

SVAT CVP800 Manuale utente

Marantz

Marantz PMD620 Manuale utente

Zoom

Zoom H4next Manuale utente

Roland

Roland BR-900CD Manuale utente

JVC

JVC ProHD GY-HMZ1U Manuale operativo e di manutenzione

Panasonic

Panasonic PQT8531-P Manuale utente

Sanyo

Sanyo TRC-6400 Manuale utente

Tascam

Tascam DR-07 Manuale utente

Olympus

Olympus DW-90 Manuale utente

Sanyo

Sanyo ICR-B150 Manuale utente

Korg

Korg D4 Manuale utente

Sony

Sony ICD-SX46 - Ic Recorder Manuale utente

Olympus

Olympus DIGITAL VOICE RECORDER WS-200S Istruzioni per il montaggio