Atari 2600 Manuale utente

Altri manuali per 2600

6

Indice

Manuali Scrivania popolari di altre marche

HP

HP m9060n - Pavilion - Elite Scheda tecnica

Asus

Asus E210 Series Manuale utente

Dell

Dell Inspiron 600m Manuale utente

Dell

Dell Inspiron 3662 Manuale utente

TotalFlow

TotalFlow uFLO Manuale utente

HP

HP Presario SV7000 - Desktop PC Manuale utente

HP

HP ProDesk 400 G5 Manuale

Logitech

Logitech MK320 Manuale utente

Dell

Dell XPS 730 H2C Manuale utente

Sony

Sony Vaio Series Manuale utente

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer Manuale utente

Alto

Alto MD 250 Manuale utente

Lenovo

Lenovo ThinkCentre Edge 72 Manuale

Lenovo

Lenovo ThinkStation D20 Manuale

Arbor Technology

Arbor Technology FPC-7800 Series Manuale utente

Sony

Sony VAIO VGX-TP1 Series Manuale utente

Asus

Asus Eee Box B204 Manuale utente

Dell

Dell Optiplex 9010 All In One Manuale utente

www.retroelectronik.com

Atari 2600 Woody and Darth Vader PAL AV mod

installation instructions

Thank you for your interest in our AV mod,it will permit you to play on about any modern Tvs with

brighter images and better sound.

Prerequisites :

This job is pretty easy, you ll only have to do 4 soldering points on your motherboard.However a

small skilled in soldering iron is needed or you could damage your Video system.

WARNING : risk of electrical shock

Please also keep in mind that for your safety, you must unplug power cord and wait at least 5

minutes to discharge all capacitors prior to operate your game console.

We couldn t be held as responsible for any harm you could do to yourself or to your properties

What are you going to need ? :

- The most important thing : the av mod

-A soldering iron and a some solder wire

- A drill with 6mm or 7mm bit (1/4")

- Screwdrivers

- a cutting pliers

- A needle-nose pliers

- optionally a hot glue gun or a strong glue

This AV mod can be installed in less than 15mn but please take your time, you should be able to do

the job in less than 30mn.

First ,remove these 4 screws and open the case :

Then remove gently the motherboard from its plastic case.

You re going to see a big metal shield present in both side of the motherboard,we re going to need to

remove it.

Fortunately,the metal shield isn t soldered,it s

just maintained from a side to the other by

some small bended tabs.

You just have to unbend each of these tabs

(located in the back of the motherboard)

with a needle-nose pliers to remove the

metal shield.

Once removed you can forget it,we won t

replace this shield as we re not going to use

HF anymore

Our beautiful motherboard is nude,we re going to cut the contact with the RF part.

To do that, we re going to remove 4 components and to cut or unsolder RF box pins Optionally we

can also desolder the RF box ;

Concerning the components to remove,you can unsolder them but i ve personally simply cutted

them using a cutting pliers

Components to remove :

Then we re going to cut or

unsolder the 5 pins of the

RF Box :

We can also optionally unsolder and remove completely the RF Box as we re not going to use it

anymore. To do that,there is 4 big solder points to desolder, they re linked to the GND so it s easy to

do and there is no major risks.points to unsolder :

To connect your AV mod ,only 4 solder points are needed.See the back of your AV mod to know

which wire to solder ( Concerning GND please solder the biggest wire to the motherboard)

Below are the 4 solder points to do :

Open 2 6-7mm (1/4") holes on the case to fix the RCA chassis connectors.

There is much more space than inside a 2600JR and so they is plenty convenient place that you can

choose :

Fix the two RCA connectors on the chassis :

Now solder the Audio-out on the white or red (may vary) RCA connector , solder de Video-out to

the red or black RCA connector. Then connect both RCA GND together and to the GND power

small wire ,just like this :

you can now fix your AV mod with the double sided tape provided. There is a perfect place just near

the « Game Reset » switch. The result should be something like :

Time to test, place a cartridge, connect the A2600 to your TV and plug the power cord.

You should have a noiseless brighter image.

If the image is not good enough, you can adjust it by turning the pot located near the on/off switch

but actually it shouldn t be necessary

So then check everything one last time and you can close the case, place back the 4 screws and

play !

We wich you hours of gaming with your newly improved Atari 2600 !

Please contact us if you have any question