Atec M2 Manuale utente
CAUTION
WARNING!
>Read this document completely before using this machine.
>Due to speed of the thrown ball, a pitching machine can be dangerous if
not used with extreme care and caution.
>Never put any part of your body or any foreign object on/or near any
moving parts. Doing so could cause severe injury or death.
>Inspect machine thoroughly before every use. Do not use if any parts
are worn, damaged, or missing. Failure to do so can result in serious injury
or death.
>This machine should be operated with adult supervision ONLY.
>Always use a grounded 110 Volt electric outlet.
< 100 feet - #16/3 extension cord
100 - 200 feet - #14/3 extension cord
> 200 feet - #12/3 extension cord or consult a local electrician.
>Batters & feeders must wear a protective helmet with facemask at all times.
>Use a protective screen to shield the operator and machine.
>Keep body parts, clothing and hair away from all moving parts.
>Never use this machine near water or with damp or wet balls.
>Always test the pitch location before allowing a hitter to step into the
batter’s box. This will assure proper alignment of the machine and safe
delivery of pitch.
>Always turn your machine completely off when it is not in use.
>Manufacturer or seller of this machine assumes no liability for personal
injury or property damage caused directly or indirectly by the use of this
machine, regardless of reason, whether the machine failed mechanically or
whether damage was caused in normal operation of the machine.
MAINTENANCE
Your machine comes with a Limited Warranty.
Under normal use and care ATEC guarantees, to the original owner, the
machine to be free from defects in materials and workmanship with the
following limitations,
5-years on all structural components.
2-years on all moving and wear components.
During this period ATEC will repair or replace with new or refurbished
components, at ATEC’s sole discretion, any component found to be
defective without cost to the owner, provided the defective product is
returned to the factory at the owner’s expense. Proof of purchase may be
required by ATEC to approve certain warranty claims.
This product is not intended for commercial use. Commercial use of this
product without the prior written consent of ATEC will void your warranty.
ATEC machine wheels are made of elastometric urethane which
maximize ball grip and overall machine performance. This material,
by nature, is very pliable. To maintain optimum performance, never
store or transport your machine laying on its throwing wheel(s).
Also, never store or transport your machine in an environment that
exceeds 120°F.
ATEC training machines require little maintenance, but there are a
few actions that will extend the life of your machine.
1. Keep the machine clean. Clean any dust or dirt from all parts of
the machine after each use. Use a soft dry cloth and wipe the frame
and wheel. Note: Only clean your machine when it is unplugged
and all parts have stopped moving.
2. Some types of balls may cause a buildup of residue on the
wheel’s tread. Light buildup will not affect the machine’s
performance, however you will need to clean the tread if the buildup
becomes excessive. To remove residue from the tread: unplug the
machine and wait for the wheel to stop. Use 80-grit sandpaper to
lightly sand the surface of the wheel’s tread.
3. The motor is sealed and requires no lubrication/maintenance.
4. Any maintenance or repair to the motor or electrical
components must be performed only by a qualified technician.
WARNING: After turning your machine off, the wheel(s) will continue
to turn for 2-3 minutes. DO NOT attempt to move the machine until the
wheel(s) stop completely. DO NOT attempt to stop the wheel(s) with
your hand or any other object.
ATEC Customer Service
(p) 1.800.755.5100
QUESTIONS?
WARRANTY
GENERAL CARE
M2SAFETY + MACHINE CARE
M2
QUICK START + OPERATION
MACHINE DIAGRAM GENERAL OPERATION
TOP VIEW
MACHINE ORIENTATION
HITTER OPERATOR
1- On/Off Switch
2- Speed Control
3- Speed Chart
4 - Ball Chute
5 - Wheels
6 - Fuse Box
7 - Frame
8- Tilt Adjustment Handle
9- Vertical Adjustment Handle
10 - Horizontal Adjustment Handle
11 - Protective Hand Guard
12 - Adjustment Grip
13 -Transport Wheels
1
6
4
5
3
2
1. Place the machine the desired pitch distance from home plate.
*Recommended machine distance is 50-60 feet
2. Position legs so that two are directed toward the plate & one is back, toward
the operator (see Machine Orientation).
3. Check that the On/Off Switch (1) is set to the “off” position.
4. Standing behind the machine, plug your M2 into a 110 volt power source.
*Always use a 3-prong plug & 16 gauge or heavier power cord.
5. Always use a Protective Screen for the safety of the operator.
6. Aim the machine at the approximate pitch direction using the Adjustment
Handles (8,9 & 10) and tighten the handles to secure the machines position.
7. Turn the machine On and set Speed Control Knobs (2) to the desired speed
setting. Allow the motors time to reach the proper speed before feeding a ball.
8a. Test the pitch location by feeding a ball into the Ball Chute (4). Confirm pitch’s
location multiple times before allowing a batter to step into the box.
8b. Make adjustments to the machines orientation as needed, and tighten all
handles after any adjustments are made. Test pitch location after all adjustments.
9. Always set the speed and type of pitch to a level consistent with the ability,
experience, and comfort level of the batter.
10. Always alert the batter verbally or with a routine visual signal and wait for an
acknowledgement from the batter prior to pitching the ball.
11. Never mix balls types in a single training session. Mixing brands, types of
balls, or balls with different degrees of wear/age will negatively affect the
consistency and accuracy of the machine.
12. When adjusting your machine, always loosen the appropriate Adjustment
Handles before moving the machine as desired, then tighten.
1. Position machine’s head completely vertical, with top wheel directly above bottom
wheel (Figure A).
2. Reference Speed Chart (3) and set wheel speeds accordingly on the Speed
Control (2). The speed selected should never exceed the batter’s comfort level.
3. Aim machine and test the pitch location. Continue to make adjustments to the
machine’s alignment as needed and always test the pitch location before allowing a
hitter enter the batter’s box.
1. Reference Speed Chart (3) and set wheel speeds accordingly on the Speed
Control (2). The speed selected should never exceed the batter’s comfort level.
2. Loosen Tilt Adjustment Handle (8) by turning it counter-clockwise. This will allow
the machine head the freedom to tilt.
**Always be cautious when making adjustments to the machine, and never put
any body parts or clothing near the machine’s moving parts.**
3. Tilt machine throwing head into position (Figure B or C). The angle of throwing
head will determine the directional break of the pitch.
4. Tighten Tilt Adjustment Handle (8) by turning it clockwise. This will secure the
machine’s tilt function.
5. Loosen Vertical Adjustment Handle (9) by turning it counter-clockwise. This will
allow the machine head the freedom to aim up or down.
6. Tilt machine head back to raise the pitch trajectory. Since curveballs break
downwards, the machine must be aimed up to compensate for the pitch’s break.
7. Tighten Vertical Adjustment Handel (9) by turning it clockwise. This will secure
the machine’s vertical adjustment function.
8. Loosen Horizontal Adjustment Handle (10), move machine left of center for a left
hand curveball, or right of center for a right hand curveball. Re-tighten the Horizontal
Adjustment Handle by turning it clockwise.
9. Test the pitch location. Continue to make adjustments as needed and always test
the pitch location before letting a hitter enter the batter’s box.
1. Reference Speed Chart (3) and set wheel speeds accordingly on the Speed
Control (2). The speed selected should never exceed the batter’s comfort level.
2. Loosen the Tilt Adjustment Handle (8) by turning it counter-clockwise. This will
allow the machine head the freedom to tilt.
**Always be cautious when making adjustments to the machine, and never put
any body parts or clothing near the machine’s moving parts.**
3. Tilt machine throwing head into a completely horizontal position (Figure D)
4. Tighten Tilt Adjustment Handle (8) by turning it clockwise. This will secure the
machine’s tilt function.
5. Loosen Horizontal Adjustment Handle (10) by turning it counter-clockwise, move
machine left of center for a left hand slider, or right of center for a right hand slider.
Re-tighten the vertical adjustment handle.
6. Test the pitch location. Continue to make adjustments as needed and always test
the pitch location before letting a hitter enter the batter’s box.
FASTBALL
FASTBALL to CURVEBALL
FASTBALL to SLIDER
8
10
11
12
13
9
Figure B
Right Hand Curveball
Figure A
Fastball
Figure C
Left Hand Curveball
Figure D
Slider
7
Altri manuali Atec Accessori
