Atec A590TM Manuale utente
• Supports most 46”- 110” Flat Panel TVs
Model: A590TM
+0 to -15
For technical assistance or troubleshooting
please call 1-800-936-1168
This product Wall Mount frame is intended for use only with an apparatus which has a maximum weight of 132 lbs. See apparatus
instructions. Using with an apparatus heavier than the maximum weight indicated may result in instability and cause possible
injury.
READ THIS FIRST
Read this entire manual! Do not attempt to install this product if you do not understand the instructions. Contact a qualified
mount installer if you have any doubts about a safe and secure mount installation, or if you are not sure what specific wall
materials you are attaching this mount to. Check all the parts carefully to make sure there are no missing or damaged parts.
Improper installation may result in damage to your TV, property, and personal injury.
• Maximum Weight Capacity: 132 lbs.
• Supports VESA Sizes up to 700x600
Tilting Flat Panel Wall Mount
This product is intended only to mount a television of the indicated size and weight. Using this
product to mount televisions heavier than the maximum weight capacity can damage equipment
and cause personal injury.
Schoenfeld International Inc. and ATEC are not responsible for personal injury or product
damage due to mishandling, incorrect mounting, incorrect assembly, or incorrect use of this
product.
How and where you use your television wall mount is extremely important for Child Safety
As you set up and use your new product, keep all of these safety tips in mind.
• One size of TV wall mount does not fit all TVs. Use only a TV wall mount rated for the weight
of your TV and the size of your screen. Your TV wall mount assembly instructions contains
specific information on the maximum weight and screen size combination that your wall
mount can safely support. Do not exceed the maximum weight of screen size for any TV wall
mount.
• Carefully read all of enclosed instructions for proper use of this product. If you have any
doubts about safe and secure assembly, please contact a professional.
• Don’t let children climb on or play with mounts or TVs.
• Remember that children can become excited while watching a program, especially on a
“larger than life” TV. Make sure to place or install the TV wall mount where it cannot be
pushed, pulled on, or knocked down.
• Make sure that you route all cords and cables so that they cannot be pulled or grabbed by
curious children.
Always wear safety goggles to when drilling or installing hardware.
Tools
For your convenience, we have included an allen wrench with this mount. For the best assembly
experience and mounting safety, we always recommend using full-size tools for each assembly
step.
Below is a recommended tool list you will need for proper and safe installation. See applicable
warnings in this manual about certain types of mounting surface materials and the special hardware
and tools that should be used.
• Drill with a specific size drill bit to pre-drill holes in the wall
• Stud finder
• Tape measure
• Pencil
• Screw drivers
• Socket wrenches
• Small hammer
• Safety goggles
1
Wall Plate
2
Bracket
x2
3
Tilt Adjustment Rod
x1
I
2
M4x20mm Bolts
M4x30mm Bolts
M5x20mm Bolts
17mm Spacers
M4/M5 Washers
M8x55mm Bolts
M6x40mm Bolts
3
Allen Wrench
1
F
B
M5x30mm Bolts
M6x25mm Bolts
84
4
A
1
C
E
4
J
K
M6/M8 Washers
Socket Tool
4
12
4
8
L
M
22mm Spacers
4
10mm Spacers
4
M8x45mm Bolts
4
D
N
1
Tilt Adjustment Rod Bolt
O
P
Q
R
4
4
Wall Plate
M8x25mm Bolts
H
M6x50mm Bolts
G4
4
S
T
Brackets
Tilt Adjustment Rod
Long Bolts
Long Bolt Washers
Concrete Anchors
1
2
14
4
4
1
Concrete Anchors
Ax8 Bx8 Cx8
Long Bolts
Long Bolt Washers
x14
Tx1
Allen Wrench with Phillips End
Tilt Adjustment Rod Bolt
M5x6mm
x1
8
4
Attach the Tilt Adjustment Rod
Lay the Brackets (2) on a flat surface with the flat side laying down. Insert the Tilt Adjustment Rod (3)
into the outer hole in the side of either Bracket (2) as shown in Fig. 1a below.
The Handle of the Tilt Adjustment Rod (3) can be located on either side of the TV. Make sure the
Handle will be on the side of the TV you will be able to easily access the Handle. You will need to
turn the Handle to adjust the tilt angle of the TV.
Carefully push the Tilt Adjustment Rod (3) through both holes on each Bracket (2).
Insert the Tilt Adjustment Rod Bolt (T) into the Tilt Adjustment Rod (3) and tighten with the
phillips end of the Allen Wrench (4).
Fig. 1a
Handle
3T
Handle
3
2
2
Center the Brackets (2) vertically on the rear of the TV. Attach the Brackets (2) to the rear of the TV
using four of the Bolts (D-M) with the proper size Washers (Q-R) as shown in Fig. 1b. Tighten using
the Allen Wrench (4). Do not over tighten.
NOTE: IF YOUR TV SCREEN SIZE IS 60” TO 110” PLEASE FOLLOW THE
DIRECTIONS FOUND ON PAGE 6 WHICH USES THE PROVIDED SPACERS.
Do not force the bolts into the mounting holes on your TV. Do not use an electric drill to
tighten these bolts on your TV. This could damage the equipment or cause personal injury.
CAUTION: Do not place the TV face down on a hard surface when installing the mounting plate
on the TV. Placing the TV face down on a hard surface can result in equipment damage. Use a
blanket or other suitable surface.
If your TV has a straight rear, and your screen size is 55” or less, spacers are most likely not
necessary.
For correct installation, install the Brackets (2) with the hook on each bracket facing down.
D-M Q-R
D-M
Q-R
5
Fig. 1b
Attach the TV Bracket to the rear of the TV (continued)
If your television has a curved back, and the mounting holes are recessed (Fig 1c) spacers are
required. Install the proper size Spacers (N-P) between the TV rear and the bracket structure as
shown in Fig 1e. to make sure the Brackets (2) extend past the rounded portion of the TV. Then use
the selected Bolts (D-M),Washers (Q-R), and the Allen Wrench (4) to attach the bracket structure
(with the spacers between the bracket and the TV) to the TV as shown in Fig 1d. Make sure the bracket
structure is properly aligned on the rear of the TV and securely tighten the bolts. Do not over tighten.
Fig. 1e
Fig. 1d
D-M
N-P
Q-R
D-M Q-R
N-P
Fig. 1c
N-P
2
6
7
10mm
M8x55mm M6x50mm
THESE INSTRUCTIONS ARE FOR ATTACHING THE TV BRACKETS TO 60-110”
SCREEN SIZE LED FLAT PANEL TELEVISIONS
For 60-70” LED TVs: Attach the brackets to the rear of the television using the M6x50mm Bolts (J),
22mm Spacers (P), and the M6/M8 Washers (R). Make sure to install the spacers between the rear
of your TV and the bracket as shown below. Tighten the bolts using a phillips head screwdriver.
Do not over tighten.
For 70-110” LED TVs: Attach the brackets to the rear of the television using the M8x55mm Bolts (M)
& 22mm Spacers (P), as well as the 10mm Spacers (N), & M6/M8 Washers (R). Make sure to install
the spacers between the rear of your TV and the bracket as shown below. Tighten the bolts using a
phillips head screwdriver. Do not over tighten.
22mm M6/M8
25
0
15
55
35
sretemillim
50
WASHER
SPACER
SPACER
Mx4 Jx4 Px4 Nx4 Rx4
BE SURE TO FOLLOW THE SAFE
MOUNTING PROCEDURES ON PAGES 11 & 12
RN
P
J-M
8
9
Fig. 3a
2-1/2” (65mm)
Fig. 3b
Fig. 3c
1. Use a pencil, awl, or a nail to mark the location of the wall stud centers (Fig. 3a) after locating the
stud with an electronic stud locator. The distance between the marks should not be less than 16
inches (Studs must not be less than 16” inches.)
2. Place the Wall Plate (1) flat against the wall with the center of the mount in the desired location,
aligning the holes in the mount with the studs (Fig. 3b). Use the wall mount plate as a template to
mark the location of the four mounting holes on the wall. Make sure that the mounting holes are
level and are parallel using the built-in level on the front of the Wall Plate (1).
3. Use 3/16” (5mm) drill bit to pre-drill holes at least 2.5” (65mm) deep at the marked locations (Fig. 3d).
4. Use a wrench, the four Long Bolts (A), and Washers (C) to attach the wall mount to the wall as
shown in Fig. 3c. Do not use wall anchors in wood stud walls.
5. Use the Level placed on the front of the Wall Plate (1) to level the wall mount, repositioning as
necessary, then firmly tighten the bolts. Do not overtighten.
16"
CAC
A
1
Fig. 3d
2.5” (65mm)
Fig. 3e
Fig. 3f
Fig. 3g
10
1. Place the Wall Plate (1) flat against the wall in the desired location. Use the wall plate as a
template to mark the location of the four mounting holes on the wall. Make sure that the mounting
holes are level and parallel. Make sure the horizontal holes are no closer than 16” (Fig. 3e).
2. Use 3/8” (10mm) drill bit to pre-drill four holes at least 2.5” (65mm) deep (Fig 3f) at the
marked locations.
3. Insert a Wall Anchor (B) into each pre-drilled hole and lightly tap it with a hammer until the wall
anchor is flush with the wall.
4. Use a wrench, the four Long Bolts (A), and Washers (C) to attach the wall mount to the wall with
the Wall Anchors (B) (Fig 3g).
5. Use the Level placed on the front of the mounting plate to level the wall mount, repositioning as
necessary, then securely tighten the bolts.
Concrete wall
A
A
C
C
C
B
Indice
Altri manuali Atec Rack e supporto
