Atec A570TS Manuale utente

Tilting Flat Panel Wall Mount

Installation Guide

• Supports most 32”-60” Flat Panel TVs

• Maximum weight capacity: 110 lbs.

• Supports VESA Sizes up to 500X400

This product Wall Mount frame is intended for use only with an apparatus which has a

maximum weight of 110 lbs. See apparatus instructions. Using with an apparatus heavier

than the maximum weight indicated may result in instability and cause possible injury.

READ THIS FIRST!

Read this entire manual! Do not attempt to install this product if you do not understand the

taching this mount to. Check all the parts carefully to make sure there are no missing

or damaged parts. Improper installation may result in damage to your TV, property, and

personal injury.

• Easy installation

• Built-in level for easy positioning

• Safety bolts lock the TV on the mount

• Easy to adjust tilt angle:

+5 to -15 degrees

Model: A570TS

E331265

This product is intended only to mount a television of the indicated size and weight. Using this

product to mount televisions heavier than the maximum weight capacity can damage equipment

and cause personal injury.

Schoenfeld International Inc. and ATEC are not responsible for personal injury or

product damage due to mishandling, incorrect mounting, incorrect assembly, or incorrect use of

this product.

CHILD SAFETY

How and where you use your television wall mount is extremely important for Child Safety

As you set up and use your new product, keep all of these safety tips in mind.

your TV and the size of your screen. Your TV wall mount assembly instructions contains spe-

safely support. Do not exceed the maximum weight of screen size for any TV wall mount.

•Carefully read all of enclosed instructions for proper use of this product. If you have any doubts

about safe and secure assembly, please contact a professional.

• Don’t let children climb on or play with mounts or TVs.

•Remember that children can become excited while watching a program, especially on a “larger

than life” TV. Make sure to place or install the TV wall mount where it cannot be pushed, pulled

on, or knocked down.

•Make sure that you route all cords and cables so that they cannot be pulled or grabbed by curi-

ous children.

Always wear safety goggles to when drilling or installing hardware.

Tools

For your convenience, we have included an allen wrench and a socket tool with this mount. For the best

assembly experience and mounting safety, we always recommend using full-size tools for each assem-

bly steps.

Below is a recommended tool list you will need for proper and safe installation. See applicable warnings

in this manual about certain types of mounting surface materials and the special hardware and tools that

should be used.

• Drill with a speciﬁc size drill bit to pre-drill holes in the wall

• Stud ﬁnder

•Tape measure

• Pencil

• Screw drivers

• Socket wrenches

• Small hammer

• Safety goggles

The actual appearance and quantity of parts may be different than shown in the illustration. Consult

the table for actual quantities.

NOL M

JIA-H K

Right bracket

Square washers

Long bolts

Wall anchors

Long bolt washers

Spacers

Description

Wall Mount

Left bracket M8×25mm bolts

ID Description

Qty

Cable cover

Box Wrench

M4x20mm bolts

Qty

Security safety bolts

M4x30mm bolts

M5x20mm bolts

M5x30mm bolts

M6x25mm bolts

M6x40mm bolts

M8×45mm bolts

M4/M5 washers

M6/M8 washers

Step 1: Attach the left and right brackets to your TV

Do not force the bolts into the mounting holes on your TV. Do not use an electric drill to tight-

en these bolts on your TV. This could damage the equipment or cause personal injury.

CAUTION: Do not place the TV face down on a hard surface when installing the mounting plate

on the TV. Placing the TV face down on a hard surface can result in equipment damage. Use a

blanket or other suitable surface.

Check your TV manual to conﬁrm the required bolt diameter according to the size, depth, and position

of the mounting holes in your TV.

For correct installation, install the brackets with the hook on each bracket facing down.

Install the bolts, spacers, and square washers in accordance with the following:

If your television has a straight back, spacers are not required. Use the selected bolts (A-H) and

square washers (I) to install the bracket directly on the back of the television as shown in Fig 1a.

Make sure that the two brackets are equal in height and are level. Once the brackets are aligned,

securely tighten the bolts.

keep the bracket snug to the rear of the TV without over tightening.

If necessary, use additional washers (N, O) to make sure the bolts (A-H)

A-H

Fig. 1a

Fig. 1b

Step 2: Install the cable cover

Route the cables as required. Snap the cable cover into place on the rods (Fig. 2a), and then slide the

cover into position as required (Fig. 2b).

Slide down

Fig. 2a Fig. 2b

A-H

If your television has a curved back and mounting

holes are recessed (Fig. 1a) spacers are required.

Install the spacers (M) between the display and

the bracket as shown in Fig 1b. Then, use the

appropriately selected bolts (A-H) applicable to your

TV and the square washers (I) to install the brack-

ets with spacers to the back of the television. Make

sure that the two brackets are equal in height and

are level. Once the brackets are aligned, securely

tighten the bolts (Fig 1b). If neccessary, use addi-

tional washers (N,O) to make sure the Bolts (A-H)

keep the brackets snug to the rear of the TV without

over tightening.

Step 3: Attach the wall mount to the wall

Find and mark the best position for the wall mount on the wall.

The best viewing height is parallel to the eye level of a person sitting on a couch. Normally, this is

about 4 feet above oor level.

In addition to your eye level height when you are seated, the following two measurements will help

you determine the perfect height for your wall-mounted television:

• The distance from your viewing location to the wall.

• The vertical distance from eye level to the oor plus the distance from your viewing location to the

wall when the viewing angle is 15 degrees.

For example:

• If distance ‘a’ is 5 to 7 feet (1.5 to 2.1 meters), distance ‘b’ is about 1 foot (0.3 meter)

• If distance ‘a’ is 8 to 13 feet (2.4 to 4 meters), distance ‘b’ is about 3 feet (0.9 meter)

• If distance ‘a’ is 14 to 17 feet (4.3 to 5.2 meters), distance ‘b’ is about 4 feet (1.2 meters)

Add the eye level height plus ‘b’ to get the ideal height of the center of the television display.

After determining the ideal height on the wall for your television, follow the mounting instructions for

your type of wall construction: wood stud or concrete walls.

Attaching this mount to wood studs or concrete walls requires special tools and hardware to

ensure the mount is securely and safely attached to these materials. Concrete will break or

crumble if special concrete drill bits and drill operating speeds are not properly used. Consult

a professional if you are unsure or have any doubts about the safety of the installation. Per-

sonal injury or equipment damage can result if the mount is not properly installed.

Fig. 3

Wood stud walls (Fig 3b)

1. Use a pencil, awl, or a nail to mark the location of the wall stud centers (Fig 3b) after locating the

stud with an electronic stud locator. The distance between marks should not be less than 16 inches

(Studs must not be less than 16 inches (40.6 cm).

ing the holes in the mount with the studs (Fig 3c). Use the wall plate as a template to mark the

location of all four mounting holes on the wall. Make sure that the mounting holes are level and are

parallel.

3. Use a 5 mm drill bit to pre-drill holes at least 40 mm (1.6 inches) deep at the marked locations.

4. Use the supplied box-end wrench (6), the four long bolts (J), and washers (L) to attach the wall

mount to the wall. Do not use wall anchors in wood stud walls.

5. Use the built-in level to level the wall mount (Fig 3d), repositioning as necessary, then securely

tighten the bolts.

Fig. 3b Fig. 3c

Fig. 3d

Concrete Walls:

to mark the location of all four mounting holes on the wall. Make sure that the mounting holes are

level and are parallel.

2. Use a 10 mm drill bit to pre-drill four holes at least 50 mm (2 inches) deep at the marked locations.

3. Insert a wall anchor

(K)

into each pre-drilled hole and lightly tap it with a hammer until the wall anchor

4. Use the supplied box-end wrench (6), the four long bolts (J), and washers (L) to attach the wall

mount to the wall with the wall anchors.

5. Use the built-in level to level the wall mount (Fig 3d), repositioning as necessary, then securely

tighten the bolts.

LJ6

The distance between marks should not be less than 16 inches

(Studs must not be less than 16 inches (40.6 cm).

Step 4: Hang the television display

A large television requires two people to lift. Schoenfeld International Inc. and ATEC are not

responsible for equipment damage or personal injury due to mishandling.

ensuring that it is securely installed can result in equipment damage or personal injury.

1. Lift the television display with the brackets securely attached to the wall mount.

2. Hook the top of brackets over the top bar of the wall mount (Fig 4a).

3. Rotate the display to let the brackets hook over the bottom bar of the mount. Then install a safety bolt

(5) into the lower end of each bracket to lock the television in place (Fig 4b).

Fig. 4a Fig. 4b

Fig. 5

Step 5: Adjusting the tilt angle

This patented design features an unique tilt angle mechanism that can easily be adjusted by just one

person. No tools are required for this step. As shown in Fig. 5, grasp the top and bottom of the mount-

ed ﬂat panel and gently pull the top of the ﬂat panel toward you or back to adjust the viewing angle.

After mounting, if the TV does not stay in your preferred viewing angle there is not enough tension

on the two screws found on the inner side of each “angle-free” bracket. Follow the six steps below to

adjust (tighten) the tension of the bracket screws to prevent this issue.

1. Carefully remove the TV from the wall mount bars and place the screen face down on a ﬂat surface

that is clean and without objects of any kind. The rear of the ﬂat panel with the “angle-free” mount

brackets attached is facing upward towards the ceiling.

2. Use a regular slotted screwdriver to remove the four black rubber screw “caps” found on the inner

side of each bracket.

3. Use the Box wrench (6) to tighten all four of these nuts (two nuts on each bracket) 1/4 turn to the

right. After tightening, replace the black plastic caps over each screw.

4. Carefully lift up the TV and properly attach the brackets to the mount bar and secure the safety

latches

5. Adjust the “angle-free” tilt to your proper viewing position and without letting go of the TV, lessen

your hand pressure to see if the angle tilt is properly held in place by the mount. If additional tension

is still required, repeat steps 1 – 5. Do not over-tighten these nuts or the “angle-free” tilt adjustment

will not function at all.

6. Once the proper tension is achieved, replace the black rubber caps on the exposed ends of the

screw/nuts

Mount Reference Dimensions

Adjustable bracket spacing: 200 – 700 mm

(7.87 in – 27.55 in)

Bracket height: 530 mm (20.86 in)

Bracket frame height: 180 mm (7.08 in)

Bracket frame length: 820 mm (32.28 in)

In some cases depending on the weight of your TV, the bracket angle tension may require a one-

time adjustment.

LIMITED SIX-YEAR WALL MOUNT WARRANTY

We warrant this product to you, the original purchaser at the time of purchase printed on a dated store receipt from

an authorized ATEC retailer and for a period of six-years thereafter that our wall mount product and all it’s parts

and components are free of defects in material and workmanship under normal use. This warranty is subject to

the provisions below. ATEC’s sole obligation and the purchaser’s exclusive remedy pursuant to these warranties

are limited to replacement at ATEC’s sole discretion. There are no other warranties except as expressively set

forth below either expressed or implied, including any warranty of merchantability for any particular purpose.

Should you be missing any of the assembly parts or components (screws, pieces, etc.), please contact the

Customer Support Center to secure a replacement. It is not necessary to bring the unit back to the store. When

calling, please reference the parts list found in the Instruction Manual to help us accurately identify the missing

parts and promptly provide replacements.

Our Customer Support Center is available Monday to Saturday (10:00AM to 7:00PM EST) for technical assistance

or troubleshooting. To contact us please call 1-800-936-1186.

This warranty is expressly limited to the replacement of wall mount parts and components described in the parts

list located in the Instruction Manual included with the product.

This warranty applies under conditions of normal use.

This warranty does not cover: any product, which has been subject to damage due to improper assembly or

disassembly, products which were not assembled, installed, used, or maintained in accordance with the product

assembly instructions & warnings, acts of nature, misuse, neglect, accidents, abuse, exposure to elements,

outdoor use, extreme temperature ranges, damage during transit, commercial use, modification of, or to any part

of the product or attachments to the product not approved by ATEC. Also not covered are costs for

assembly/dis-assembly labor, costs incurred in shipping the unit or parts for warranty repair/exchange or any

products purchased from unauthorized ATEC sellers. Under no circumstances shall ATEC, be liable for any loss

(direct, indirect, incidental, foreseen, unforeseen, special or consequential) or for any damage arising out of, or in

connection with, the use of this product. Nor shall ATEC have any responsibility for incidental or consequential

damages resulting from the breach of this warranty including but not limited to inconvenience, purchase or rental

of replacement products, loss of profits or commercial loss.

We reserve the right to request damaged parts or units be shipped to our offices for inspection or confirmation of

any warranty claims.

This warranty does not cover product sold ‘As Is’.

This warranty is valid only to the original purchaser of the Product in the United States and Canada and grants

specific legal rights.

Indice

Altri manuali Atec Supporto TV

Atec

Atec A675STS Manuale utente

Manuali Supporto TV popolari di altre marche

Ergotron

Ergotron Neo Flex Cantilever UHD Manuale utente

StarTech.com

StarTech.com FPCEILBTB Manuale utente

VonHaus

VonHaus 05/038 Manuale utente

Techlink

Techlink ECHO TV Manuale utente

Sandstrom

Sandstrom SSTVMC12X Manuale utente

Sony

Sony SU-WL700 Guida

ICW

ICW SCACC18 Manuale utente

LG WM-L640V Manuale utente

Gembird

Gembird WM-65ST-01 Manuale utente

ERARD

ERARD FiTUP XXL 035320 Manuale utente

PEERLESS

PEERLESS PLCK-1 Guida

Kanto

Kanto RCF180 Manuale utente

GEM

GEM GEM GP001 Manuale utente

Gladiator Joe

Gladiator Joe GJ0A0053 Manuale utente

Vivotek

Vivotek AM-105 Manuale utente

Vivo

Vivo VESA STAND-VAD1B Manuale utente

AmazonBasics

AmazonBasics B07QG3LMG4 Manuale utente

Secura

Secura QLF210 Manuale utente