For additional information, including detailed installation and how-to videos, please visit www.atinorthamerica.com.
Problem? Please do not return the product to the place of purchase. Please first visit our website at atinorthamerica.com for helpful information and
videos.
Need
more
help?
Please
contact
us
directly
at
[email protected] or
(303)
459-21
1
9
and
we
’ll
be
happy
to
help.
Parts List
1. Fixture
2. Control Box
3. Hanging Kit
4. Antennae
5. Power-cord
Installation
1. Remove the acrylic shield.
2. Insert bulbs into all available slots by sliding both ends
into the socket pair. The labeled end should line up
over the hole in the fixture. Rotate each bulb 90º to
lock it into place.
3. Remove the protective film, if present, from the acrylic
shield and slide back into the fixture. The acrylic
shield should be used at all times. (Long, visible
scratches that parallel the long side of the fixture
are normal as they are caused by the shield rubbing
against the frame of the fixture.)
4. Use the supplied hanging kit to hang the fixture over
your aquarium at a minimum distance of 8 inches
above the water surface.
5. Connect the lamp cord to the control box.
6. Connect the power-cord to the control box.
7. Plug control box into power and wait for both green
lights on the Ethernet port to come on and stay
fully illuminated. This may take a few minutes. Wait
another full minute after both green lights come on
before proceeding.
8. Connect control box to computer.
a. Wired Connection: Connect an Ethernet cable
from the port on your computer to the port on the
control box.
b. Wireless Connection: Open the wireless settings
and connect to “ATI-Fixture.” This also may take
a few minutes. (While you are connected to the
control box wirelessly, you will not be able to
access your normal wireless internet connection.)
9. Open a web browser and navigate to 192.168.1.1/login
10. Login with default username and password:
(admin/admin)
11. Select your language.
12. Set new username and password. Write them down or
save them as there is no way to retrieve them if they
are forgotten.
13. Choose your type of lamp.
a. 24” fixture = 1 module (1x75W)
b. 36” fixture = 2 module (2x75W)
c. 48” fixture = 3 module (3x75W)
d. 60” fixture = 4 module (4x75W)
14. Run self-test.
15. Save settings.
16. Login again with your new username and password.
17. Open the “Settings” tab and set the fan value. Do NOT
skip as failure to set the fans correctly may cause the
fixture to overheat and cause damage to the fixture.
a. For a 4 or 6 bulb fixture: enter 5
b. For an 8 bulb fixture: enter 7
18. Use the default program installed with your fixture or
create a new one using the Chart and Lamp tabs.
(See reverse side for lots of great help.)
Warranty
For warranty information, please visit atinorthamerica.com.
Troubleshooting
For troubleshooting, maintenance and other frequently
asked questions, please visit atinorthamerica.com.
Safety
Please take great care when installing and using this
fixture. This is an electrical device, and as with any
electrical device used in or around an aquarium, caution
must be exercised. Failure to do so may result in
electrocution, fire, serious bodily injury, or even death.
Please follow these safety requirements carefully, as
failure to do so could void the warranty and cause serious
safety hazards.
NEVER operate the fixture if it has been damaged or is
malfunctioning.
NEVER operate the fixture or control box with wet hands
or if the unit is wet.
NEVER re-wire, re-configure or modify the fixture or
control box in any way.
NEVER use with generators.
NEVER grab the fixture or control box by the power or
lamp cords, as this may cause the wires to become exposed.
NEVER install the fixture or control box outdoors or in a
wet environment.
NEVER subject the fixture or control box to direct heat
such as sunlight or heat lamps.
ALWAYS unplug the fixture and control box from its
power source before doing any work on the fixture.
ALWAYS leave a little bit of slack in the power and
lamp cords.
ALWAYS use a 3-prong grounded outlet or plug.
ALWAYS keep fixture and control box out of reach
of children.
