Atlas TC255 Manuale utente
Read this entire manual before operation begins.
Record below the following information which is located on the serial number
data plate.
Serial No.
Model No.
Date of Installation
Contents
Introduction . . . . . . . . . . . . . . . 5
General Information . . . . . . . . . . . 8
Transportation, Unpacking And Storage . 13
Installation . . . . . . . . . . . . . . 14
Operation . . . . . . . . . . . . . . . 22
Inflating . . . . . . . . . . . . . . . . 30
Accessories . . . . . . . . . . . . . . 33
Maintenance . . . . . . . . . . . . . . 35
Trouble-Shooting. . . . . . . . . . . . 37
Electric And Pneumatic Diagram. . . . . 39
Warranty . . . . . . . . . . . . . . . 42
4
TC255
Printing Characters And Symbols
Throughout this manual, the following symbols and printing characters are used
to facilitate reading:
Indicates the operations which need proper care
Indicates prohibition
Indicates a possibility of danger for the operators
BOLD TYPE Important information
WARNING: before operating the machine, read carefully
Chapter 7 Installation where all proper operations for a
better functioning of the machine are shown.
Introduction 5
TC255
Introduction
1.1 Introduction
Thank you for purchasing an Atlas tire changer. The machine has been
manufactured in accordance with the very best quality principles. Follow the
simple instructions provided in this manual to ensure the correct operation and
long life of the machine. Read the entire manual thoroughly and make sure you
understand it.
1.2 Machine Identification Data
A complete description of the “Tire Changer Model” and the “Serial number”
will make it easier for our technical assistance to provide service and will
facilitate delivery of any required spare parts. For clarity and convenience, we
have inserted the data of your tire changer in the box below. If there is any
discrepancy between the data provided in this manual and that shown on the
plate fixed to the tire changer, the latter should be taken as correct.
1.3 Manual keeping
For a proper use of this manual, the following is recommended:
• Keep the manual near the machine, in an easily accessible place.
• Keep the manual in an area protected from the damp.
Type:
Volt: Amp: Kw:
Ph: Hz:
Year of manufacturing:
Air supply: 8-10 bar (115 – 145 PSI)
LOGO
Introduction 6
TC255
• Use this manual properly without damaging it.
• Any use of the machine made by operators who are not familiar with the
instructions and procedures contained herein shall be forbidden.
This manual is an integral part of the product: it shall be given to the new owner
if and when the machine is resold.
The illustrations have been made out of prototypes pictures. It
is therefore possible that some parts or components of standard
production differ from those represented in the pictures.
1.4 General Safety Precautions
The tire changer may only be used by specially trained and
authorized expert personnel.
• Any tampering or modification to the equipment carried out without the
manufacturer’s prior authorization will free him from all responsibility for
damage caused directly or indirectly by the above actions.
• Removing or tampering with safety devices immediately invalidates the
guarantee.
• The tire changer comes complete with instruction and warning transfers
which are designed to be long-lasting. If they should for any reason be
damaged or destroyed, please ask immediately for replacements from the
manufacturer.
1.5 Scrapping
When your machine’s working life is over and it can no longer be used, it must
be made inoperative by removing any connection to power sources.
These units are considered as special waste material, and should be broken
down into uniform parts and disposed of in compliance with current laws and
regulations.
If certain parts are pollutants or non-biodegradable, deliver them to the
appropriate handling station.
Introduction 7
TC255
To The Reader
Every effort has been made to ensure that the information contained in this
manual is correct, complete and up-to date. The manufacturer is not liable for
any mistakes made when drawing up this manual and reserves the right to make
any changes due the development of the product, at any time.
General Information 8
TC255
General Information
2.1 Intended Use
• This automatic tire changer has been designed and manufactured
exclusively for removing and mounting tires from/onto rims from 10” to
30” and a maximum diameter of 47”.
• In particular THE MANUFACTURER cannot be held responsible for any
damage caused through the use of this tire changer for purposes other
than those specified in this manual, and therefore inappropriate, incorrect
and unreasonable.
2.2 Description Of Machine
Bead press arm
Leverless
Mounting tools
Wheel positioner
Bead breaking carriage
Control panel
Inflation
System
Front panel
General Information 9
TC255
2.3 Description Of Controls
2.3.1 Pedals On Front Panel
PEDAL “L”
This pedal is used to tilt back the vertical arm out of the working position.
PEDAL “M”
This pedal is used to rotate the spindle clockwise or
anticlockwise, in slow or fast rotation mode.
PEDAL “N”
This pedal is used to lift the tire from the ground onto
the spindle flange or lower it back down to the ground.
2.3.2 Control Panel
SELECTOR “A”
• When it is selected into LOCKING position, the horizontal movement of the
bead breaker carriage is restricted, and in the meantime the button (C) is
activated.
• When it is selected into UNLOCKING position, the bead breaker arm can
have the normal movements horizontally.
CONTROL LEVER “B”
• When it is pushed leftwards, the bead breaker
carriage moves forwards.
• When it is pushed rightwards, the bead breaker
carriage moves backwards.
BUTTON “C”
• This button works only when the selector (A) is
set in LOCKING position.
• When it is pressed, the bead breaker carriage
makes an over stroke: moves forwards about 1”.
• When it is released, the bead breaker carriage moves back to the initial
position automatically.
General Information 10
TC255
CONTROL LEVER “D”
• When it is pushed upwards, the bead breaker arm moves upwards.
• When it is pushed downwards, the bead breaker arm moves downwards.
2.3.3 Leverless Mounting Tools
CONTROL LEVER “H”
• When it is pushed downwards, the tool is out of its seat and
moves downwards.
• When it is pushed upwards, the tool moves back in position.
2.3.4 Bead Press Arm
The bead press arm is used to
facilitate mounting and demounting
the run-flat tire. It can be moved
upwards and downwards by means
of the control lever (E).
2.3.5 GT Inflation System
The GT inflating system consists of the
gauge, the tire deflation button (G) and
the quick blasting device.
• To inflate the tire, press the pedal
(Z) at side of the machine.
• During inflation, if the pressure
exceeds the value recommended
by the tire manufacturer, press the
button (G) to deflate the tire.
• To make the quick blaster, position
the blasting nozzle towards the rim
center just under the rim lip and
press the buttons (F).
Indice
Altri manuali Atlas Equilibratrice
