AUDAC AMP203 Istruzioni per l'installazione

AMP203 commands manual

Index

Using the commands 3

Configuration and settings commands 5

Routing commands 6

Volume + Mute commands 7

Using the commands

The commands can be sent to the AMP203 by IP or using a serial RS485 connection. Please refer to the infor-

mation below on how to connect to the AMP203:

RS485 Configuration details

RJ45 (RS485, Digital audio, +24V DC):

For connection to Wall Panels & Paging Consoles

Pin 1 White-Orange n/c

Pin 2 Orange n/c

Pin 3 White-Green +24V DC

Pin 4 Blue RS485 A

Pin 5 White-Blue RS485 B

Pin 6 Green GND

Pin 7 White-Brown n/c

Pin 8 Brown n/c

TCP/IP Configuration details

IP Address User configurable

Port 8711

Max connections 1

Command flow

1) UDP commands can be sent to the AMP’s IP address on port 8711. Alternatively the commands can be sent

to Multicast address 239.254.222.222 (or broadcast) on port 8711.

2) The AMP203 acknowledges the command by returning the same command and a ‘+’ as Argument. (ACK)

In case of a get command the AMP203 will return the current state of the specific get command.

3) The AMP203 sends a Multicast/Broadcast update on port 8712 with the new state. This information is used

for AUDAC Touch 2. This multicast group can be joined by any (user specific) application to receive a constant

flow of the device’s status updates.

Note: When sending commands to the multicast address, all the AMP203 devices with the same device address

(P001 for example) will receive this command and then execute it.

Command overview

Each command is followed by an ‘x’ character, which represents the number of the slot whereto the

command is sent. If the audio player doesn’t support multiple slots, the number ‘1’ shall always be

used.

Example: Get IP---

ASCII: #|P001|F001|GIP|U|return

HEX: 237C533030317c463030317c4749507c557c72657475726e0a

Notes

• The checksum is CRC-16 excluding the ‘#’. The checksum can always be replaced by

‘U’, which is always accepted.

• Return in ASCII : <CR> <LF> HEX : 0x0D 0x0A (carriage return & line feed)

• Source address has a maximum length of 4 characters and cannot contain ‘|’ or ‘#’

CONFIGURATION AND SETTINGS COMMANDS

GIP

Get info about the ip address, subnet mask and gateway the AMP203 is using:

Command: GIP

Arguments: None (0)

Feedback: dhcp^ip4.ip3.ip2.ip1^mask4.mask3.mask2.mask1^gw4.gw3.gw2.gw1^

DHCP: dhcp ON(1) or OFF(0)

IP: IP4 address of unit

MASK: subnet mask

GW: IP4 address of gateway

Example: Get info about the IP address

#|S001|F001|GIP||crc|<CR><LF>

AMP203 replies: #|F001|S001|IP|0^192.168.0.197^255.255.255.0^192.168.0.1|crc|<CR><LF>

SIP

Set IP address, subnet, gateway and dns servers:

Command: GIP

Arguments: ^ip4.ip3.ip2.ip1^mask4.mask3.mask2.mask1^gw4.gw3.gw2.

gw1^dns4.dns3.dns2.dns1

dhcp : dhcp ON(1) or OFF(0)

ip : IP4 address of unit

mask : subnet mask

gw : IP4 address of gateway

dns : IP4 address of dns server 1

Feedback: + : acknowledge

Example: Set the IP address

#|F001|S001|SIP|0^192.168.0.197^255.255.255.000^192.168.0.1^8.8.8.8^0.0.0.0|U|<CR><LF>

AMP203 replies: #|F001|S001|SIP|+|crc|<CR><LF>

ROUTING COMMANDS

SRD01

Set program down

Command: SRD01

Arguments: None (0)

Feedback: + : acknowledge

SRU01

Set program down

Command: SRU01

Arguments: None (0)

Feedback: + : acknowledge

SR01

Set routing

Command: SR01

Arguments: y

y: 1-4 are Dante channels 1-4

y: 5 is ch1+2

y: 6 is ch+4

y: 7 is ch2+1

y: 8 is ch4+3

Feedback: + : acknowledge

GR01

Get routing

Command: GR01

Arguments: None (0)

Feedback: y

y: 1-4 are Dante channels 1-4

y: 5 is ch1+2

y: 6 is ch3+4

y: 7 is ch2+1

y: 8 is ch4+3

VOLUME + MUTE COMMANDS

SVU01

Set volume up

Command: SVU01

Arguments: None (0)

Feedback: + : acknowledge

SVD01

Set volume down

Command: SVD01

Arguments: None (0)

Feedback: + : acknowledge

SV01

Set same volume for left and right channel

Command: SV01

Arguments: y

y: 70 (refers to -70dB, lowest level)

y: 0 (refers to 0dB, highest level)

Feedback: + : acknowledge

GV01

Get volume

Command: GV01

Arguments: None (0)

Feedback: y

y: volume level from -70 up to 0 dB

SM01

Set mute

Command: SM01

Arguments: None (0)

Feedback: y

y: 0 (unmute)

y: 1 (mute)

GM01

Get mute

Command: GM01

Arguments: None (0)

Feedback: y

y: 0 (unmute)

y: 1 (mute)

SGIA

Set gain for all channels

Command: SGIA

Arguments: x1: gain channel 1

x2: gain channel 2

x3: gain channel 3

x4: gain channel 4

for every channel the gain will be set (-110 up to +24)

Feedback: + : acknowledge

GGIA

Get gain for all channels

Command: GGIA

Arguments: None (0)

Feedback: x1: gain channel 1

x2: gain channel 2

x3: gain channel 3

x4: gain channel 4

for every channel the gain will be displayed (-110 up to +24)

SGI

Set gain for 1 specific channel

Command: SGI

Arguments: x: channel number (1-4)

y: gain channel x

the gain for channel x will be set to value y (-110 up to +24)

Feedback: + : acknowledge

Altri manuali per AMP203

Altri manuali AUDAC Amplificatore

AUDAC

AUDAC CAP412 Istruzioni per l'installazione e il funzionamento

AUDAC

AUDAC PRE16 Istruzioni per l'installazione e il funzionamento

AUDAC

AUDAC Multi-functional SourceCon MFA208 Manuale utente

AUDAC

AUDAC COM12 Mk2 Manuale utente

AUDAC

AUDAC PRE116 Manuale utente

AUDAC

AUDAC DPA616 Manuale utente

AUDAC

AUDAC DPA152 Istruzioni per l'installazione e il funzionamento

AUDAC

AUDAC Multi-functional SourceCon MFA208 Manuale utente

AUDAC

AUDAC SCP2 Series Manuale utente

AUDAC

AUDAC COM12 Istruzioni per l'installazione e il funzionamento

AUDAC

AUDAC D2 Istruzioni per l'installazione e il funzionamento

AUDAC

AUDAC AMP203 Manuale utente

AUDAC

AUDAC PRE220 Manuale utente

AUDAC

AUDAC AMP20 MK2 Manuale utente

AUDAC

AUDAC CAP224 Manuale utente

AUDAC

AUDAC CPA12 Istruzioni per l'installazione e il funzionamento

AUDAC

AUDAC AMP20 Manuale utente

AUDAC

AUDAC DPA74 Istruzioni per l'installazione e il funzionamento

AUDAC

AUDAC SMA Series Manuale utente

AUDAC

AUDAC CEP Series Manuale utente

AUDAC

AUDAC CPA24 Istruzioni per l'installazione e il funzionamento

AUDAC

AUDAC PX110 Manuale utente

AUDAC

AUDAC COM108 Manuale utente

AUDAC

AUDAC PMQ240 Manuale utente

Manuali Amplificatore popolari di altre marche

ASTRO

ASTRO HVO V40 P Manuale utente

Marantz

Marantz SUPERSCOPE BLA-545 Istruzioni per il montaggio

NAD

NAD CI980 Manuale utente

Technics

Technics SE-CH770 Manuale utente

Harman Kardon

Harman Kardon HK6300 Manuale utente

NAD

NAD T975 Manuale utente

McIntosh

McIntosh MA6850 Manuale utente

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manuale utente

Viatron

Viatron Autrix Manuale utente

GME

GME GA9800 Manuale utente

Atlas

Atlas CP700 Manuale utente

Roland

Roland KC-1000 Manuale utente

Pyle

Pyle PFMRA350BW Manuale utente

Advantage

Advantage S-250 Manuale utente

IRT Electronics

IRT Electronics DVA-3007 Manuale utente

Dimavery

Dimavery BA-100 Series Manuale utente

Sony

Sony XM-S400D Manuale utente

Schertler

Schertler ROY X Manuale utente