AUDIO TELEX ATC5488 Manuale utente
ATC5488 TONE GENERATOR MODULE
INSTALLATION I NSTRUCTIONS
Thank you for choosing an Audio Telex ATC5488 tone generator module. The ATC5488 has four tones available. These are
Evacuatim and Al€rt Tones, both to A52220.1-2 standards, as well as a Bell Tone and a Pre Announce Chime. lnstallation into any
Audio Telex manufuchred mixer or amplifier is made simple by utilising a standard '€nd' qpe connector plug supplied on the
module and a rec€ptacle, already installed into the mixer or amplifier. Please follow these easy instructions for installation.
E The installation of lhe ATC548E involvcs eccess to thc inside of the rmplitrers or mixerg Inst tlrtion should only bc
rttemptcd by a qualifed technicirn. Alwlys turn off the AC power and rcmove the AC power cord bcfore attempting
to scc.ss thc inside of lhcsc prodlcts. Plerse contrct your Errest Audio Telex oftce for detdls of your trefcat
qualified technicirn '
For installation into an lC30 amplifier: Locate the empty 7 pin 'and' connector receptacle on the mixer PCB to the left of the
heat sink when looking from the front panel. Connect the module to this receptacle, ensuring that the wires from the connector exit
towards the rear ofthe amplifier.
For installation into an AT SERIES amplmer: Lo€ate the empty 7 pin 'end' connector receptacle on the mixer PCB between
the reble pot and the master volume pot. Connect the module lo this receptacle, orsuring that the wires from the connector exit
towards the right hand side ofthe amplifier when looking from tlre front panel.
For installation into an SA SERIES amplifier: Locate the ernpty 7 pin 'end' connector receptacle on the mixer PCB
betweer input Ch. 6 pot and the bass tonal contol pot. Connect the module to this receptacle, ensuring that the wires from the
conneclor exit towards the rear ofthe amplifier.
For lnstallatlon into a TX6000 or TX8000 mlxer: Locate the empty 7 pin 'end' connector receptacle behind input Ch. 5 pot
on the mixer PCB. Comect the module to this receptaclg ensruing that the wires from the connector exit towards the rear of the
mixcr-
For installaUon lnto a TX8200 stereo mlxer: Locate the eflpty 7 pin 'end' corulector receptacle on the mixer PCB b€tween
input Ch. 8 pot and the Left Channel Mast€r out pot. Connect the module to this receptacle, ensuring that the wtes from the
connector exit towards the rear ofthe mixer.
Connectlon to ampllfler:
Connections
Orange= Output
Black : Grormd
Blue = Mute switch to I
Red = DC Supply (Min. I2VDC, Max. t SVDC)
Black = Common
White = Evac,uation Tone
Yellow: Bell Tone
Purple = Alert Tone
Blue = Pre Annormce Chime
Connectlons to swltched signal:
Notes
Trim Pot Note that the tim pot located in positim RlO on the module attenuates the level out of the ATC5488 and works in an
urti-clockwise fashion ie, hnned fully clockwise will completely att€nuate the signal outpl$ whilst hrned fully anti-clockwise will
allow full signal present though to the amplifier stage.
r\'.1 ri
TONE IIODULE
ILACK = CEHMEN TRI POT Rlo = LEVA- rlUT
I,IHIIE . EVAC
YB.LII, = BELL
PURPLE . ALERT
DLIJE ' PRE ANNT]UNCE
ORANGE = OU]PUT
BLACK - @IruND
ELUE = I{UTE SITITCH TE I
RE! - DC SUPPLY
oln 1aVDC UAX 18VDC)
ATC54B8 TINE MEDULE
Indice
Altri manuali AUDIO TELEX Apparecchiature di registrazione
Manuali Apparecchiature di registrazione popolari di altre marche
Strymon
Strymon NIGHTSKY Manuale utente
Mitsubishi Electric
Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Manuale utente
Tews Technologies
Tews Technologies TPMC465 Manuale utente
Honeywell
Honeywell Excel 50 Manuale utente
SeaLevel
SeaLevel COMM+8.LPCI Manuale utente
Arturia
Arturia AUDIOFUSE STUDIO Manuale utente
