AudioCodes MediaPack 1288 Manuale utente

1 |Page

MediaPack™ 1288 Analog Gateway

Quick Setup Guide

Welcome

Congratulations on purchasing your AudioCodes MediaPack 1288 (MP-1288) High-Density Analog Gateway,

hereafter referred to as device!

This document is only intended to provide basic setup instructions for initial access to the device and

connecting it to your network. For advanced configuration and cabling, refer to the device's User's Manual and

Hardware Manual respectively, which can be downloaded from AudioCodes website at

https://www.audiocodes.com/library/technical-documents.

Before you begin, please read the Safety Precautions on page 9.

Package Contents

Make sure that the following items (in addition to any separate-orderable items that you may have purchased)

are included with your shipped device:

2 x front-mounting brackets for 19-inch rack mounting

1 x RJ-45-to-DB-9 serial cable adapter for serial communication

(AC-powered models) 2 x AC power cords

(DC-powered models) 2 x DC terminal blocks

1 x grounding lug

Regulatory Information document

2 |Page

Physical Description of Front Panel

Fan Tray module cover

SYS

LED indicating system status:

Green On

Device is operating normally or initial boot-up stage when device is

powered on

Orange On

Device is approaching high-temperature threshold, but not yet

critical

Red On



Fault detected in CPU module, or

Incompatible or faulty software version (.cmp file) detected

during boot up, or

Approaching critical high-temperature threshold

Off

No power

TEL

LED indicating FXS blade status:

Green On



Boot-up phase

Normal device and FXS blade operation

Orange On

At least one DSP has reached high-temperature threshold

Red On

Initial power-up stage, or

Failure detected in at least one FXS blade, or



No FXS blade detected

Off

No power

PWR

LED indicating power status:

Green On

Chassis receiving power and Power Supply modules are

functioning normally. If the device is configured to use only one

Power Supply module, the LED is lit if at least one of them is

operating normally

Red On

One of the Power Supply modules is faulty (if device is configured

to use two Power Supply modules)

Off

No power

FAN

LED indicating fan status:

Green On

Fans are functioning normally

Red On

At least one fan in the Fan Tray module is faulty

Off

No power

3 |Page

Physical Description of Rear Panel

CPU

Central processing unit (CPU) module, providing:

Reset pinhole \\ button for resetting the device (2-10 second press) and restoring

factory defaults (11-30 second press)

STAT LED indicating CPU status (same as SYS LED on front panel)

RS-232 serial interface port (RJ-45)

USB Type-A port which can be used, for example, for various storage capabilities

with an external USB hard drive or flash disk



2 x 100/1000Base-T (Gigabit) Ethernet ports (RJ-45) with status LED:

Green On

Ethernet link established

Green Flashing

Data is being received or transmitted

Off

No Ethernet link

PS1 / PS2

Power Supply modules with status LED:

Green On

Connected to power source, chassis receiving power and Power

Supply module's fan is operating normally

Orange Flashing

Connected to power source, but chassis not receiving power or

fault detected in Power Supply module's fan.

If only one of the Power Supply modules is connected to the

power source, the LED on the disconnected Power Supply

module flashes orange.

Off

No power

FXS Blades

Each FXS blade provides 3 FXS port connectors (50-pin Telco connector of Centronics

type). Each connector provides 24 FXS interfaces and therefore, each blade provides up to

72 FXS interfaces (3 x 24 FXS). The device can be housed with up to 4 FXS blades. Each

blade provides a status LED:

Green On

FXS blade initialization completed and functioning normally

Orange On

Less than a third of the FXS ports are out of service.

Red On

FXS blade initialization has not completed or a failure detected

in the FXS blade due to more than a third of the FXS ports are

out of service or a DSP failure

Off

No power

4 |Page

Mounting the Device

You can mount the device in a standard 19-inch rack.

1. Attach the two front-mounting brackets (supplied) to both sides of the chassis. Each bracket is secured

to the chassis using 9 screws (supplied).

2. With two people, lift the chassis into the rack from the front of the rack.

3. Hold the chassis for support while the second person positions the chassis so that the front-mounting

brackets are flush against the front-rack posts and that the holes of the front-mounting brackets are

aligned with the holes on the front-rack post.

4. Hold the chassis in position while the second person secures the two front-mounting brackets to the

front posts, by finger-tightening 19-inch rack bolts (not supplied) to the rack posts. Each mounting

bracket is secured to the rack by two bolts. Make sure that the left and right front-mounting brackets

are attached to the rack posts at the same level so that the chassis is supported in a horizontal position.

5. Tighten the bolts on the front-mounting brackets.

5 |Page

Cabling the Device to Power

The device can be powered from a standard alternating current (AC) electrical wall outlet or a DC power

source.

1. GROUNDING: Ground (earth) the device by inserting an electrically earthed strap of 16-AWG

(minimum) wire in to grounding lug (supplied), and then attaching the lug to the chassis using the two

screws and spring washers. For more information, refer to the device's Hardware Manual. Connect the

other end of the strap to protective earthing. This must be in accordance with regulations enforced in

the country of installation.

2. AC POWER: For each AC power model, connect the line socket of the AC power cord (supplied) to the

device's AC power inlet, located on the rear panel. Connect the plug at the other end of the AC power

cord to a standard electrical wall outlet.

6 |Page

3. DC POWER: For each DC power model, disconnect your DC wires from your DC power source, and

then connect the two DC wires (6-AWG) to the DC terminal block plug (supplied), making sure that the

wires are inserted in to the correct openings on the terminal block according to their polarity (negative

or positive). Insert the DC terminal block plug into the DC inlet of the Power Supply module, located on

the rear panel. Connect the DC power leads to a 48-VDC power source.

7 |Page

Assigning an IP Address

Use the device's factory default IP address (192.168.0.2/24 and Default Gateway 0.0.0.0) to initially access the

device's Web-based management interface and then change it to suit your network's addressing scheme for

subsequent connectivity.

1. Using a CAT-5e/6 shielded twisted pair (STP) straight-through RJ-45 Ethernet cable, connect any one of

Ethernet ports of the CPU module (rear panel) to the LAN port of your computer.

2. Change the IP settings of your computer to correspond with the device's default IP address and subnet

mask.

3. On your computer, open a standard Web browser (for example, Google Chrome), and then in the URL

field, enter the device's default IP address; the Web Login screen appears:

4. Type in the default username (Admin) and password (Admin), and then click Login.

5. Open the IP Interfaces table (Setup menu > IP Network tab > Core Entities folder > IP Interfaces).

8 |Page

6. Select the OAMP interface ('Application Type' with OAMP + Media + Control), click Edit, and then in

the dialog box, modify the device's OAMP interface.

7. Click Apply to submit your changes; your connection with the device becomes unavailable at the

default IP address (due to the new IP address).

8. Change the IP settings of your computer to correspond with the new OAMP IP addresses and subnet of

the device.

9. Access the device again, but at its' new IP address, and then on the Web interface's toolbar, click the

Save button; the new IP address is now saved to the device's flash memory.

10. Re-cable the device to the required network. You can now access the device's management interfaces

remotely, using the new IP address.

Obtaining Software and Documentation

If you have a maintenance and support agreement with AudioCodes, you can download the device's latest

software version from AudioCodes' Services Portal at https://services.audiocodes.com (registered users only).

You can also view and download documentation relating to the device (such as the User's Manual and

Hardware Manual)on AudioCodes website at https://www.audiocodes.com/library/technical-

documents?productGroup=1692.

9 |Page

Safety Precautions

The device must be installed and serviced only by qualified service personnel.

The device is considered as IPX0 non-water ingress protected and therefore, must be installed only

indoors.

Do not expose the device to water or moisture.

Ethernet cabling must be shielded and routed only indoors, and must not exit the building.

Do not open or disassemble this device. The device carries high voltage and contact with internal

components may expose you to electrical shock and bodily harm.

Make sure the device is installed in a well-ventilated location to avoid over heating of internal

components and subsequent damage.

Do not place any object on top of the device and make sure that sufficient clearance from the top and

sides are maintained to ensure proper airflow to avoid over heating of internal components.

Operate the device in an ambient temperature (Tma) that does not exceed 40°C (104°F).

The device must be installed only in restricted access locations that are compliant with ETS 300 253

guidelines where equipotential bonding has been implemented.

The device includes an integrated secondary surge protection, but does not provide primary telecom

protection! When the FXS telephone lines are routed outside the building, additional protection -

usually a 350V three-electrode Gas Discharge Tube (GDT) as described in ITU-T K.44 - must be provided

at the entry point of the telecom wires into the building (usually on the main distribution frame / MDF),

in conjunction with proper grounding. The center pin of the GDT (MDF grounding bar) must be

connected to the equipotential grounding bus bar of the Telecommunication room.

Operate the device only from the type of power source indicated on the chassis.

Installation of the device must be in accordance with national electrical codes and conform to local

regulations.

AC power: Use only the supplied AC power cord for connection to the AC power source.

AC power: The device must be connected to an electrical socket-outlet providing a protective earthing

connection.

AC power: If you are using both Power Supply modules, connect each one to a different AC power

supply source. The two AC power sources must have the same ground potential.

DC power: Connect the device to a safety extra-low voltage (SELV) source that is sufficiently isolated

from the mains.

DC power: Connection of the device to the DC mains power must be done only by a certified electrician

and in accordance with local national electrical regulations.

DC power: Both Power Supply modules must be connected. Ensure that you connect each one to a

different DC power supply source.

DC power: The two DC power sources must have the same ground potential.

10 |Page

About AudioCodes

AudioCodes Ltd. (NasdaqGS: AUDC) is a leading vendor of advanced voice networking and media processing

solutions for the digital workplace. With a commitment to the human voice deeply embedded in its DNA,

AudioCodes enables enterprises and service providers to build and operate all-IP voice networks for unified

communications, contact centers and hosted business services. AudioCodes’ wide range of innovative

products, solutions and services are used by large multinational enterprises and leading tier one operators

worldwide.

International Headquarters

1 Hayarden Street,

Airport City

Lod 7019900, Israel

Tel: +972-3-976-4000

Fax: +972-3-976-4040

AudioCodes Inc.

200 Cottontail Lane,

Suite A101E,

Somerset, NJ 08873

Tel: +1-732-469-0880

Fax: +1-732-469-2298

Website: https://www.audiocodes.com/

MediaPack, What’s Inside Matters, OSN, SmartTAP, User Management Pack, VMAS, VoIPerfect, VoIPerfectHD, Your

Gateway To VoIP, 3GX, VocaNom, AudioCodes One Voice and CloudBond are trademarks or registered trademarks of

AudioCodes Limited. All other products or trademarks are property of their respective owners. Product specifications are

subject to change without notice.

Document #: LTRT-29860

Date Published: 02/04/2019

Indice

Altri manuali AudioCodes Portale

AudioCodes

AudioCodes Mediant 2000 Manuale utente

AudioCodes

AudioCodes MediaPack MP-40x series Manuale utente

AudioCodes

AudioCodes Mediant 800B Manuale utente

AudioCodes

AudioCodes MediaPack MP-263-DB Manuale utente

AudioCodes

AudioCodes Mediant 2000 Manuale utente

AudioCodes

AudioCodes mediapack MP-500 Manuale utente

AudioCodes

AudioCodes Mediant 500L MSBR Istruzioni per il montaggio

AudioCodes

AudioCodes Mediant 2000 Manuale utente

AudioCodes

AudioCodes Mediant 800B Manuale utente

AudioCodes

AudioCodes Mediant 3000 TP-6310 Manuale di installazione e funzionamento

AudioCodes

AudioCodes MediaPack MP-124 Manuale utente

AudioCodes

AudioCodes MediaPack MP-262 Manuale utente

AudioCodes

AudioCodes MP-252 Manuale utente

AudioCodes

AudioCodes Mediant 3000 Manuale utente

AudioCodes

AudioCodes MP-26 series Manuale utente

AudioCodes

AudioCodes E-SBC Manuale utente

AudioCodes

AudioCodes Mediant 2000 Manuale utente

AudioCodes

AudioCodes MediaPack MP-263 Manuale utente

AudioCodes

AudioCodes Mediant 600 Manuale utente

AudioCodes

AudioCodes Mediant 800B Manuale utente

AudioCodes

AudioCodes Mediant 2000 Istruzioni per il montaggio

AudioCodes

AudioCodes MediaPack Manuale utente

AudioCodes

AudioCodes Mediant 800C SBC Guida di riferimento rapido

AudioCodes

AudioCodes Mediant 1000 Manuale utente

Manuali Portale popolari di altre marche

LST

LST M500RFE-AS Manuale utente

Kinnex

Kinnex Media Gateway Manuale utente

2N Telekomunikace

2N Telekomunikace 2N StarGate Manuale utente

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuale utente

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Manuale utente

Telsey

Telsey CPVA 500 - SIP Manuale utente

RTA

RTA 460A-NNA4 Scheda tecnica

Shaw

Shaw Gateway HDPVR Manuale utente

ABB

ABB VSN900 Guida rapida

Commander

Commander Pulse Manuale utente

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Manuale utente

NETGEAR

NETGEAR C6300BD Manuale utente

Amit

Amit CDW531AM Manuale utente

HMS

HMS Netbiter EasyConnect EC150 Manuale utente

Huawei

Huawei EchoLife HG620 Manuale utente

AT&T

AT&T U-verse 3801 Manuale per l'uso e la cura

Logic IO

Logic IO RTCU MX2 turbo Manuale utente

Suttle

Suttle MediaMAX MXM-521 Manuale utente