Auditronics 220 Digital Audio Console Manuale utente

220 Digital Audio Console

TECHNICAL MANUAL

March 2000

R-16 / Dec 1997

220 Digital Audio Console Technical Manual - 1st Edition220 Digital Audio Console Technical Manual - 1st Edition

220 Digital Audio Console Technical Manual - 1st Edition

AUDITRONICS

600 Industrial Drive

New Bern, North Carolina 28562

252-638-7000

*a division of Wheatstone Corporation

220/ March 2000

ATTENTIONTTENTION

TTENTIONTTENTION

TTENTION

READEAD

EADEAD

EAD MM

MEE

E!!

220 / March 2000

Attention!

This console contains static sensitive devices:

Normal precautions against static discharge should be observed when

handlingindividualmodules.Inparticular, modulesbeingpackedforshipping

for return or repair must be packed in special static protection bags before

packaging. Damage caused by static discharge may not be covered under

warranty.

Replacing Modules in a Powered-up Console:

While in an emergency situation it is possible to remove and insert modules

on a powered-up console, Auditronics does not recommend this procedure.

Whenever possible it is best to power down the console first before removing

or replacing modules.

However, if you find you must proceed with this operation, then be sure to

take the following precaution:

When re-inserting a module, take care to replug it squarely into its

mainframe connector socket, so all edgecard fingers make contact

simultaneously. In other words, the gold-plated bus connector fingers on the

bottom edge of the module's printed circuit board must be inserted squarely

(i.e., perpendicular) to the mating socket on the bottom pan of the console

mainframe. The intent is to prevent a situation where one of the module's

power pins makes significant contact before the others. (Naturally, this

same precaution must be taken when using extenders.)

Iftheaboveinstructionsarefollowedtheprocedureshouldberoutine;ifthey

are not, you could run the risk of damaging the console's logic chips.

Again, to avoid ANY possibility of this damage, whenever possible we

stronglyrecommendpoweringdowntheconsolebeforereplacinganymodules.

ATTENTIONTTENTION

TTENTIONTTENTION

TTENTION

READEAD

EADEAD

EAD MM

MEE

E!!

220 / March 2000

Console Clock Battery Backup

Console Clock Display Card

To activate battery backup of the console’s clock simply pull out the yellow

strip from the clock display card, that is mounted on the inside of console

meterbridge, as shown on the picture below.

page Contents – 1

220 / Sep 2000

CONTENTS

220 Technical Manual

Table of Contents

Chapter 1 – Installation and Power

CountertopMounting................................................................. 1-2

Clearances.............................................................................................................. 1-2

System Ground .......................................................................... 1-2

Power Supply ............................................................................. 1-4

The PSC-D340 Power Supply ................................................................................ 1-5

Power Connector Pinout......................................................................................... 1-5

PSC-D340 Power Supply Schematic ...................................................................1-5A

Energizing ............................................................................................................... 1-6

Audio and Control Wiring.......................................................... 1-7

ConnectionProcedures .......................................................................................... 1-7

Digital Connections................................................................................................. 1-7

Analog Insert Points................................................................................................ 1-7

Unbalanced Connections (analog audio) ............................................................... 1-8

Hand Crimp Tool Wiring Instructions...................................................................... 1-9

Chapter 2 - Input Module

Module Overview........................................................................ 2-2

Internal Programming Options ................................................. 2-3

Insert Bypass .......................................................................................................... 2-3

Phantom Power ...................................................................................................... 2-3

Talkback.................................................................................................................. 2-3

VDT Programming Options ....................................................... 2-4

Hook-ups..................................................................................... 2-4

Microphone Inputs ..................................................................... 2-4

Audio Connections.................................................................................................. 2-4

Control Connections ............................................................................................... 2-4

Remote ON & OFF ................................................................................................. 2-5

Cough ..................................................................................................................... 2-5

Talkback to Control Room ...................................................................................... 2-5

On Tally................................................................................................................... 2-5

Off Tally................................................................................................................... 2-6

Tally B ..................................................................................................................... 2-6

Stereo Line Analog Inputs......................................................... 2-6

Audio Connections.................................................................................................. 2-6

Stereo Line Digital Inputs.......................................................... 2-6

Audio Connections.................................................................................................. 2-6

Control Connections ............................................................................................... 2-7

220 / Oct 2001

page Contents – 2

220 / Sep 2000

CONTENTS

Remote ON & OFF ................................................................................................... 2-7

External START & STOP ......................................................................................... 2-7

Ready........................................................................................................................ 2-8

Tally B ....................................................................................................................... 2-8

DB Connector Pinout Drawing

Mono Mic Inputs ....................................................................................................... 2-9

Stereo Line Analog Inputs ....................................................................................... 2-10

Stereo Line Digital Inputs ........................................................................................ 2-11

Mono-Mic Input Signal Flow Diagram ........................................2-12

Stereo Line Input Signal Flow Diagram .....................................2-13

Chapter 3 - Output Module

Module Overview...........................................................................3-2

CPU.................................................................................................3-3

DSP.................................................................................................3-4

Serial Interface ..............................................................................3-5

Using Serial Interface ............................................................................................... 3-5

Internal Programming Options ....................................................3-6

Global Settings ......................................................................................................... 3-6

RS-485/RS-232Select ............................................................................................. 3-7

RS-485 Termination.................................................................................................. 3-7

Hook-ups........................................................................................3-8

Analog Audio Outputs............................................................................................... 3-8

Digital Outputs .......................................................................................................... 3-8

Digital Control Ports.................................................................................................. 3-9

DB Connector Pinout Drawings

Analog and Digital Outputs...................................................................................... 3-10

Digital Control Ports................................................................................................. 3-11

Master Outputs Signal Flow Diagram ........................................3-12

CPU/DSP Signal Flow Diagram...................................................3-13

Chapter 4 - Control Room Module

Module Overview...........................................................................4-2

Internal Programming Options ....................................................4-3

Cue Interrupt............................................................................................................. 4-3

Cue Mute .................................................................................................................. 4-3

Hook-ups........................................................................................4-3

Upper DB-25 “A” Connector — Audio ...................................................................... 4-3

Upper DB-25 “A” Connector — Control.................................................................... 4-4

On-Air Tally......................................................................................................... 4-4

Lower DB-25 “B” Connector — Audio ...................................................................... 4-4

DB Connector Pinout Drawing.....................................................4-5

Control Room Monitor Signal Flow Diagram..............................4-6

page Contents – 3

220 / Sep 2000

CONTENTS

Chapter 5 - Studio Control Module

Module Overview...........................................................................5-2

Internal Programming Options ....................................................5-3

External Talkback Mute/Dim..................................................................................... 5-3

Studio Dim ................................................................................................................ 5-3

Hook-ups........................................................................................5-3

Upper DB-25 “A” Connector — Audio ...................................................................... 5-3

Upper DB-25 “A” Connector — Control.................................................................... 5-4

Tally 2 and Tally 3 ............................................................................................... 5-4

Lower DB-25 “B” Connector — Audio ...................................................................... 5-4

DB Connector Pinout Drawing.....................................................5-5

Studio Control Monitor Signal Flow Diagram.............................5-6

Chapter 6 - Virtual Dip Switch

Virtual Dip Switch Application Program .....................................6-2

Installation................................................................................................................. 6-2

Hooking up the computer ......................................................................................... 6-2

Running the program ................................................................................................ 6-3

Using the program .................................................................................................... 6-5

Input attenuation ....................................................................................................... 6-8

Advanced operation................................................................................................. 6-10

Ending the program ................................................................................................. 6-12

Serial Interface Cable DB Connectors Pinout Drawing ............6-13

Chapter 7 - Superphone Input Module

Module Overview...........................................................................7-2

Caller Set-Ups .......................................................................................................... 7-2

Automatic Features................................................................................................... 7-3

Inputs and Outputs ................................................................................................... 7-3

Internal Programming Options - Main PCB ................................7-4

External In................................................................................................................. 7-4

Cue Pre/Post ............................................................................................................ 7-4

Mutes ........................................................................................................................ 7-4

Timer Restart ............................................................................................................ 7-4

Tallies........................................................................................................................ 7-4

Cue Dropout.............................................................................................................. 7-5

Gain Trimpots ........................................................................................................... 7-5

Hook-ups........................................................................................7-5

Audio Connections (Upper DB-25 “A”) ..................................................................... 7-5

Audio and Control Connections (Lower DB-25 “B”) ................................................. 7-6

DB Connector Pinout Drawing.....................................................7-7

Superphone Module Signal Flow Diagram .................................7-8

page Contents – 4

220 / Sep 2000

CONTENTS

Chapter 8 - Line Preselector Module

Module Overview...........................................................................8-2

Internal Programming Options ....................................................8-2

Hook-ups........................................................................................8-3

Audio Inputs .............................................................................................................. 8-3

Outputs ..................................................................................................................... 8-3

DB Connector Pinout Drawing.....................................................8-4

Line Preselector Signal Flow Diagram........................................8-5

Chapter 9 - Tape Remote Module

Module Overview...........................................................................9-2

DB Connector Pinout Drawing

START/STOP Function Control I/O.......................................................................... 9-3

Full-Function Control I/O .......................................................................................... 9-4

Chapter 10 - Meterbridge

Overview .......................................................................................10-2

Replacement Parts.......................................................................10-2

Digital Timer .................................................................................10-3

Console Clock ..............................................................................10-3

Controls.................................................................................................................... 10-3

Setting the time........................................................................................................ 10-4

Battery Backup ........................................................................................................ 10-4

Operational Modes .................................................................................................. 10-4

Clock/Timer(CLK-220)

Schematic ................................................................................................................ 10-5

Load Sheet............................................................................................................... 10-6

Clock/Timer Display (CLD-220)

Schematic ................................................................................................................ 10-7

Load Sheet............................................................................................................... 10-8

Chapter 11 - I/O Schematic Drawings

Mono Mic ADC I/O Card Schematic (MMADC-220) .............................................. 11-2

Analog Stereo Line ADC I/O Card Schematic (SLADC-220)................................. 11-3

Digital Stereo Line SRC I/O Card Schematic (SRC-220) ...................................... 11-4

Output Module I/O Schematic (OMD-220) ............................................................. 11-5

Control Room Module I/O Schematic (CRD-220) .................................................. 11-7

Studio Control Module I/O Schematic (SCD-220).................................................. 11-9

Superphone Module I/O Schematic (SPD-220) .................................................... 11-11

Line Select Module I/O Schematic (LS-220) ......................................................... 11-13

Appendix

Replacement Parts List ............................................................... A-2

220 / Jun 2002

INSTALLATION and POWER

page 1 – 1

220 / March 2000

Installation and Power

Chapter Contents

CountertopMounting................................................................. 1-2

Clearances.......................................................................................................... 1-2

System Ground .......................................................................... 1-2

Power Supply ............................................................................. 1-4

The PSC-D340 Power Supply ............................................................................ 1-5

Power Connector Pinout..................................................................................... 1-5

PSC-D340 Power Supply Schematic ...............................................................1-5A

Failsafe Dual Redundant Supply........................................................................ 1-6

Energizing........................................................................................................... 1-6

Audio and Control Wiring.......................................................... 1-7

ConnectionProcedures ...................................................................................... 1-7

Digital Connections............................................................................................. 1-7

Analog Insert Points ........................................................................................... 1-7

Unbalanced Connections (analog audio) ........................................................... 1-8

Hand Crimp Tool Wiring Instructions.................................................................. 1-9

220 / Oct 2001

INSTALLATION and POWER

page 1 – 2

220 / March 2000

Installation and Power

CountertopMounting

The 220 digital audio console is designed for countertop drop-in

mounting. Console placement should avoid proximity to any electro-

magneticfields,suchaslargepowertransformers,motors,andfluores-

centlightingfixtures.Therequiredcut-outwidthis371/4”andcut-out

front-to-back dimension is 19”. The front of the console will extend

approximatelyoneinchforward ofthe cut-out.The console’swooden

sidepieces will extend about 7/8” on either side of the cut-out width.

Clearances

Note the two module extractor tools (black thumbwheel screws)

mounted in the front surface of console’s lower mainframe pan (just

above and to the left of the righthand headphone jack). These must be

removed before lowering the console into its cutout!

Once in place the console mainframe pan will extend approxi-

mately 5/8 inches below the countertop surface. Note the hinged

meterbridge will require 15” above the countertop surface to open

freely. When fully open the meterbridge will extend 5 1/2” behind the

rear line of the cut-out. When closed, the meterbridge will extend

2 1/4” behind this rear cut-out line and 8 1/8” above the countertop

surface.

Do not connect the 220 console to its power supply (and do not

connect the power supply to the AC power line) until instructed to do

so.

System Ground

The first step is to ground the console.

Note that as supplied from the factory, console rackmount power

supply common, audio ground, and the 220 mainframe are connected

togetherattheconsole,butareNOTconnectedtoelectricalgroundand

the chassis of the power supply. Safety requirements dictate that a

positiveconnectionfromtheconsolemainframetoelectricalgroundbe

Indice

Altri manuali Auditronics Apparecchiature di registrazione

Auditronics

Auditronics ALM-12d Manuale utente

Auditronics

Auditronics 2600 Manuale utente

Manuali Apparecchiature di registrazione popolari di altre marche

KV2 Audio

KV2 Audio 500 Series Manuale utente

Robotics Technologies

Robotics Technologies microBus-Cam II Manuale utente

Seca

Seca 460 Manuale utente

Cognex

Cognex MVS-8000 Series Manuale utente

Mect

Mect MPNC006 Series Manuale utente

Bad Caf

Bad Caf THE LEASH Manuale utente

Strymon

Strymon NIGHTSKY Manuale utente

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Manuale utente

Tews Technologies

Tews Technologies TPMC465 Manuale utente

Honeywell

Honeywell Excel 50 Manuale utente

SeaLevel

SeaLevel COMM+8.LPCI Manuale utente

Arturia

Arturia AUDIOFUSE STUDIO Manuale utente

Rukra

Rukra RK-1240 Manuale utente

Samson

Samson SCOM Manuale utente

Dynacord

Dynacord DPS260 Manuale utente

Nice

Nice Core Manuale utente

Pyle Pro

Pyle Pro PSS8 Manuale utente

RF-System

RF-System TinyGate Manuale per l'uso e la cura