LOW PASS
It adjusts the frequency of the reverb low pass filter. Lower values will allow the lower frequ
encies to pass through the reverb effect creating a fuller, darker reverb, whereas higher values
will begin cutting off lower frequencies, which can make a reverb sound thinner and sit better
in a busy mix.
Range: 20Hz~20000Hz
Preset 8 types of High-pass filtering: BL_12, BW_12, LK_12, UR_12, BL_24, BW_24,
LK_24, UR_24
Q: UR_12, UR_24 are 0.1~1.3 adjustable, other types are stable.
PAGE 4/8
REV-EQ
ON/OFF, it is the switch to turn on or off the EQ editor.
REVERB EQ Editor
BAND: 1~5;
FREQ Range: 20Hz~20000Hz;
TYPE: PEQ: Manipulates a set range of frequencies, out in both directions from the center
frequency, with the “Q” parameter determining the width;
HS Shelf: High-pass Filtering Shelf, manipulates all frequencies above the set frequency;
LS Shelf: Low-pass Filtering Shelf, manipulates all frequencies below the set frequency;
GAIN: -30~+12dB, allows adjusting the gain of the setting frequency band.
Q: 0.1~128, adjusts the width of the PEQ filter, Lower values, create wider EQ curves
(covering wider a wider range of frequency); higher values create narrower EQ curves
(covering a much smaller range of frequencies for more surgical EQ work);
HS: High-pass Filtering, 0.1~1.3;
LS: Low-pass Filtering, 0.1~1.3;
PAGE 5/8 ECHO VOLUME/POL
ECHO VOL
Range: 0~100, the higher value the clearer effect;
ECHO POL
0 degree (+), 180 degree (-) adjustable, allows to adjust the phase of Echo;
ECHO DIR VOL
Range: 0~100, it is used to adjust the volume of direct sound;
ECHO DIR POL
0 degree (+), 180 degree (-) adjustable, it is used to adjust the phase of Echo Direct Voice.
PAGE 6/8 ECHO SETTINGS
ECHO PRE DELAY
Range: 0~100ms, it is used to adjust the amount of delay which occurs before you begin to
hear the first - repeats. Higher values can create the illusion of a much larger room as it mimics
the time that it would take for reflections from very distant surfaces to reach the listeners ears;
ECHO TIME
Range: 0~500ms, it is used to adjust the amount of delay which occurs before you begin you
begin to hear any repeats;
ECHO REPEAT
Range: 0~85%, it is used to adjust the times the delay will be repeated. The higher the value of
this parameter, the longer the delay effect will be heard before fading out;
RIGHT DELAY
Range: -50%~50%, referring to Left channel;
ECHO TO REV
Range: 0~100, it is used to adjust the volume from Echo to Reverb.
PAGE 7/8 ECHO FILTER
HIGH PASS
It adjusts the frequency of the echo high pass filter. Lower values (or OFF) allow more of the
low frequencies to be passed through the effect and yield a fuller sounding echo, whereas higher
values begin to cut off lower frequencies, creating a thinner sounding echo effect which can make
the effect sit better in a busy mix.
Range: 20Hz~20000Hz;
Preset 8 types of High-pass filtering: BL_12, BW_12, LK_12, UR_12, BL_24, BW_24,
LK_24, UR_24
Q: UR_12, UR_24 are 0.1~1.3 adjustable, other types are stable.
LOW PASS
It adjusts the frequency of the echo low pass filter. Higher values allow more of the high
frequencies to pass, creating a brighter Echo effect. Lower values will begin to cut off the higher
frequencies, creating a darker sounding echo effect.
Range: 20Hz~20000Hz;
Preset 8 types of High-pass filtering: BL_12, BW_12, LK_12, UR_12, BL_24, BW_24,
LK_24, UR_24
Q: UR_12, UR_24 are 0.1~1.3 adjustable, other types are stable.
