Aurora Lite Bank FRECON2 Manuale utente
11
11
Thank you for your purchase.
FRECON2 can be used to wirelessly synchronize the flash lights with the
camera and to remotely control any of the flash lights with built-in
FROCON2 radio system, including flash power control and modeling light
control. FRECON2 also features a co-channel relay function, the perfect
solution for triggering a remote camera in sync with remote flash lights.
Please read this user manual as well as the user manual provided with
your camera and flash light which works with FRECON2 before use.
For your safety
Before using your product, please read the following safety precaution
carefully to ensure correct and safe use.
Do not disassemble or attempt to repair it.
Do not use the product in the presence of flammable or explosive gas.
The product is not waterproof. Please keep away from rain, snow and high
humidity conditions.
Do not expose the product to high temperature over 45°C (e.g. left in a car
trunk).
Do not clean the product with organic solvent or alcohol-based liquid.
A thorough explanation of how to use the product by an adult is required
when the product is used by children. Supervise children while they are
using the product.
Consult local authorities on the proper disposal or recycling of a battery.
·1·
·2·
RED 2014/53/EU
Declaration of Conformity EC
Hereby, Aurora Lite Bank Co., Ltd. declares that this product is in compliance
with essential requirements and other relevant provisions of Directive
2014/53/EU. This product can be used with EU member states.
FCC Statement
FCC ID: 2AEJW-E2
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
Company name : AURORA LITE BANK Co., Ltd.
Equipment Name : FRECON2 transceiver
Model Name : FRECON2
Manufactured Date : AUGUST /2020
Manufacturer / Country : AURORA LITE BANK Co.,
Ltd. / CHINA
R-CS-XXX-YYYYYYYYYYYYYY
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures;
Reorient or relocate the receiving antenna.
Increase the separation between equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experience radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly
approved by manufacturer could void your authority to operate this
equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions; (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
RF Exposure information
The device has been evaluated to meet general RF exposure requirement.
The device can be used in portable exposure condition without restriction.
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT
TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE
INSTRUCTIONS.
·3·
·4·
I. Parts
II. Getting Started
Installing the batteries
Turning FRECON2 on/off
Connecting to the camera
III. States and Modes
IV. Basic Functions and Buttons
State and Mode Adjustment
Channel Selection
Group Selection
Remote Control ‒ Head Control; Model Control; Energy Adjustment
Master Mode
Command Confirmation
Test Function
Slave Button
Alarm Button
Beeper Button
Auto Power Off
Factory Settings
V. Operating Instructions
Remote Flash Synchronization
Release of Remote Camera 1
Relay
VI. Specifications
5
6
6
6
6
8
9
9
9
9
10
11
11
11
11
11
12
12
12
13
14
16
18
22
Table of Contents
I. Parts (Figure1)
Channel Indicators (1-8)
Channel Button
Group Indicators (A-F)
Group Button
Energy Adjustment Buttons
<+> Increase, <-> Decrease
Head Control Button
Slave Button
Model Control Button
Alarm Button
Command Indicator
Power Button
Master Button
Test Button
Beeper Button for FRECON2
Mode Indicators
(TRANSMIT, RECEIVE)
Mode Adjustment Button
USB Port
In Port (3.5mm)
Out Port (3.5mm)
Mounting Foot Lock Lever
Hot Shoe Mounting Foot
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
1
2
3
4
6
7
8
5
15
10
11
12
13
14
9
16
17 18
19
20
21
(Figure1)
·5·
II. Getting Started
Installing the batteries (Figure 2)
Via hot shoe (Figure 3)
Turning FRECON2 on/off
Connecting to the camera
1. Open the battery cover from the back of FRECON2.
2. Install 2 AAA batteries in accordance with the illustrated direction inside
the battery compartment.
3. Close the battery cover in place.
1. Turn on: Press the Power Button (11) to turn on the FRECON2, the
Channel indicator (1) and Group indicator (3) light up.
2. Turn off: Press and hold the Power Button (11) until all indicators light off.
1. Turn off the camera and FRECON2.
2. Slide the Hot Shoe Mounting Foot (21) of the FRECON2 into the
camera’s hot shoe mount.
3. Lock the FRECON2 by sliding the Mounting Foot Lock Lever (20) to the
right until the lock lever clicks in place.
4. Turn on the camera and FRECON2 and the shooting mode of the camera
to manual.
(Figure 2)
·6·
Via Flash Sync Cable (3.5mm - PC, Sold seperately) (Figure 4)
5. To detach FRECON2, press the lock-release button on the Mounting
Foot Lock Lever (20) while slide the lock all the way back to the left, then
slide the FRECON2 out of camera’s hot shoe mount.
1. Turn off the camera and FRECON2.
2. Insert the 3.5mm Plug of the flash sync cable into the in Port (18) of
FRECON2.
3. Insert the PC Plug of the flash sync cable into the PC terminal of the
camera. For proper connection with the camera or flash light, consult
the user manual of the actual camera or flash light at the same time.
4. Turn on the camera and FRECON2 and set the shooting mode of the
camera to manual.
(Figure 3)
·7·
III. States and Modes
FRECON2
Standard State
Transmit Mode
Receive Mode
Transmit Mode
Receive Mode
Relay State
1. The following states and modes are available in FRECON2.
2. Select the appropriate state and mode as described in this manual in
actual use.
·8·
Indice
