Autocall TrueAlert ES A59AOC-WRF Manuale utente

Cautions, warnings, and regulatory information

Important: When the notification appliance emits light or sound, it indicates the possibility of an emergency situation that requires immediate

attention of all occupants.

SAFETY: Always install, maintain, and test notification appliances within their specifications. Failure to follow all safety precautions

and instructions may result in loss of life and property due to non-functioning notification appliances. Some notification appliances

use high voltage. To avoid electrical hazards and avoid damage to appliances, make sure that the electrical power for the Notification

Appliance Circuit is disconnected at the control unit before installing, repairing, or internally adjusting any notification appliances. Even

with electrical power removed, some notification appliances (such as visible strobes) store a high voltage charge. The high voltage can

cause injury resulting in death from electrical shock. DO NOT TOUCH EXPOSED CIRCUITRY.

LOCATION REFERENCE: Location and quantity of appliances required must conform to the applicable local standards and guidelines

(the National Fire Alarm and Signaling Code (NFPA 72); ULC Standard CAN/ULC-S524, Installation of Fire Alarm Systems; the appropriate

model building codes) and specific requirements of the local Authority Having Jurisdiction (AHJ). These notification appliances are not

intended for installation within hazardous locations as defined by the National Electrical Code (NEC) or NFPA.

UL listed TrueAlert ES indoor product identification reference

Table 1: Product identification reference

Type Colors Models

Wall Mount

Audible Only

(A/O)

Red

White

Components:

A59AO-APPLWR

A59AO-APPLWW

Covers:

A59AOC-WRF

A59AOC-WWF

A59AOC-WRFAB

A59AOC-WWFAB

A59AOC-WRFQB

A59AOC-WWFQB

A59AOC-WRS

A59AOC-WWS

Operation These appliances provide an audible (AO) warning of an alarm condition when activated from the control panel of a compatible

UL/ULC Listed, Autocall Fire Alarm System.

Note: For information about TrueAlert ES appliance testing, refer to TrueAlert ES Addressable LED Appliances Troubleshooting (579-1168AC).

*One appliance

*One cover

Two 6-32 1 in. mounting screws. Do not over tighten.

Required parts:

*Autocall parts

Single gang electrical box, 1 1/2 in. minimum depth required.

Mounting instructions

1. Select the mounting location, and install the electrical box.

2. Connect the building wires to the appliance. See Wiring instructions.

3. Use the provided hardware to secure the appliance to the electrical box.

4. Set the appliance settings. See Setting the address DIP switch.

5. Attach the cover to the appliance.

Figure 1: Mounting instructions

579-1200AC Rev. E

TrueAlert ES Addressable Indoor Audible Notification Appliance installation instructions

*05791200ACE*

Wiring instructions

WARNING: Make sure that all power is disconnected before starting the installation.

1. At the electrical box, connect the building wiring to the CKT + and CKT - terminals on the assembly.

2. To ensure proper continuity, use a torque wrench to tighten the terminal block screws to 12-15 inch-pounds.

3. Maintain the correct polarity for each strobe unit.

Note: Signal Line Circuit (SLC) wiring must be twisted pair (TWP). CKT Terminals accept 2 Wires: 12-18 AWG TWP.

WARNING: Do not bring the conduit through the rear of the electrical box. Strip the lead insulation to 7/16 inches maximum.

Figure 2: Wiring instructions

Wiring notes:

a. The maximum number of addresses on an IDNAC channel is 127. The maximum number of active appliances is limited to 3 amps per

circuit. Refer to the field wiring diagrams for the driving compatible fire alarm control panel for further instructions.

b. Notification appliances are rated using an individual module label.

c. Maintain the correct polarity on the terminal connections.

d. Terminals + and - can each accommodate 2 wires, one wire going in and one wire going out to the next appliance.

e. These appliances are rated to the operating voltage limits of 23-29.5 VDC. The appliance may fail to operate as intended, and may cause

permanent damage to this equipment if it operates outside of these limits.

f. Use a compatible IDNAC power supply to operate the TrueAlert ES AO appliance.

g. T-tapping is not permitted on Class A wiring.

h. TrueAlert SLC wiring connections are supervised and power-limited.

i. Compatible IDNAC power supplies/panels: 4100ES, EPS, ES Power Supply, IDNAC card, 4007ES, 4010ES, and 4009 IDNAC Repeater.

page 2 579-1200AC Rev. E

TrueAlert ES Addressable Indoor Audible Notification Appliance installation instructions

Setting the address DIP switch

Each addressable TrueAlert ES notification appliance has a unique address that is set with an eight-position DIP switch (ADDR1). Assign up to 127

unique addresses to an SLC, however, the total appliance loading available may be less due to appliance current requirements.

To set the address, complete the following steps:

1. Locate the 8-position DIP switch on the bottom left front of the appliance, see Figure 3.

You must set the DIP switch before you snap on the cover.

2. Set the switches using a non-metallic stylus, or the equivalent.

3. Record the set address.

4. Confirm the setting for the appliance at this address with the Fire Alarm Control Panel (FACP) system configuration documentation.

DIP switch position 8 determines whether this appliance is viewed by the system as an 'ALARM' (OFF) or 'ALERT' (ON) type appliance.

Figure 3: Setting the DIP switch address

Setting the appliance configuration

You can configure certain options for the horn and strobe directly on the appliance using the appliance configuration switch (CFIG1) located on the

front of the appliance, see Figure 4.

A/O only:

Position 1: Configuration Control - OFF to enable Local Audible control,

ON for panel control.

Position 2: Audible Volume - High (OFF), Low (ON).

Position 3: Not used.

Figure 4: Setting the strobe and appliance configuration

page 3 579-1200AC Rev. E

TrueAlert ES Addressable Indoor Audible Notification Appliance installation instructions

Appliance specifications

Table 2: Environmental specifications

Specification Rating

Rated voltage range SPECIAL APPLICATION 23-29.5 VRMS

Temperature range 32 °F to 120 °F (0 °C to 49 °C)

Humidity range 10% to 93%, non-condensing at 104 °F (40 °C)

Connections Terminal for 18 AWG to 12 AWG

(0.82 mm2 to 3.31 mm2)

Table 3: Sound pressure level measurement (dBA)

Reverberant room at ten feet in accordance with

UL464 (See note 2)

Voltage (Vrms) Horn Mode Steady Horn Mode Coded (See Note 1)

23 86.9 83.3High Volume Setting using Addressable Controller

(See Note 3) 29.5 88.4 84.7

23 85.7 81.2Low Volume Setting using Addressable Controller

(See Note 3) 29.5 87.7 83.3

Anechoic room at 10 feet in accordance with ULC

S525, see note 4.

see note 4

23 93.8 93.7High Volume Setting

29.5 95.2 95.1

23 87.5 87.4Low Volume Setting

29.5 89.5 89.4

Note:

1. The coded category covers both Temporal and March time cadences.

2. Reverberant dBA measurements are a minimum UL rating based on sound power level measurements made in UL’s reverberant test

chamber.

3. High and low volume settings are configured with DIP Switch (CFIG1). See Figure 4.

4. If you install the A4905-9838 Sound Damper, the anechoic measurements decrease by approximately 9 dBA.

Table 4: ULC directional characteristics for horn

Axis Angle dBA

50° left and right -3dBAHorizontal

63° left and right -6dBA

20° above / 48° below -3dBAVertical

65° above / 60° below -6dBA

CAUTION:

• The appliances are available in red and white. Do not paint or otherwise alter the factory finishes in any way.

• Anechoic dBA levels below 85 do not meet ULC requirements for public notification.

Table 5: Maximum RMS operating current

Specification Rating

Appliance Type 23V*

AO 27 mA

* For connection to IDNAC SLCs

579-1200AC Rev. E

© 2021 Johnson Controls. All rights reserved. All specifications and other information shown were current as of document revision and are subject to change without notice. Additional listings may be applicable, contact your local Autocall

product supplier for the latest status. Listings and approvals under Tyco Fire & Security GmbH, and the product names listed in this material are marks and/or registered marks. Unauthorized use is strictly prohibited. NFPA 72 and National

Fire Alarm Code are registered trademarks of the National Fire Protection Association (NFPA).

Questo manuale è adatto per i seguenti modelli

Indice