Automationdirect.com Productivity 2000 P2-01AC Manuale utente
1
Sales 800-633-0405 www.productivity2000.com
Warranty: Thirty-day money-back guarantee. Two-year limited
replacement. (See www.productivity2000.com for details).
2000
WARNING: To minimize the risk of potential safety problems, you should
follow all applicable local and national codes that regulate the installation
and operation of your equipment. These codes vary from area to area and
it is your responsibility to determine which codes should be followed, and to
verify that the equipment, installation, and operation are in compliance with
the latest revision of these codes.
Equipment damage or serious injury to personnel can result from the
failure to follow all applicable codes and standards. We do not guarantee
the products described in this publication are suitable for your particular
application, nor do we assume any responsibility for your product design,
installation, or operation.
If you have any questions concerning the installation or operation of this
equipment, or if you need additional information, please call Technical
Support at 770-844-4200.
This publication is based on information that was available at the time it
was printed. At AutomationDirect.com®we constantly strive to improve
our products and services, so we reserve the right to make changes to
the products and/or publications at any time without notice and without
any obligation. This publication may also discuss features that may not be
available in certain revisions of the product.
Terminal Block Specifications
Number of positions 4 screw terminals
Wire Range
22-12 AWG (0.324 to 3.31 mm²)
Solid / Stranded conductor
3/64 in (1.2 mm) insulation maximum
Use copper conductors, 75°C or equivalent
Screw Driver Width 1/4 in (6.5 mm) maximum
Screw Size M3
Screw Torque 7-9 lb·in (0.882 - 1.02 N·m)
P2-01AC Power Supply
The P2-01AC Universal Input Power Supply
provides isolated power to the
Productivity2000 base from an external
100-240 VAC source.
Warning ............................. 1
Terminal Block Specifications ............ 1
Power Supply Installation Procedure....... 2
Wiring ............................... 2
General Specifications .................. 3
User Specifications .................... 3
Hot Swap Information .................. 3
2Tech Support 770-844-4200www.productivity2000.com
Power Supply Installation Procedure
Step One:
Locate the left most
socket in the base.
Step Two:
Insert the Power
Supply at a 45° angle
into the notch located
at the bottom of the
base and rotate up
until seated in socket.
Locked
Step Three:
Snap the retaining tab
into the locked position.
AC(L)
AC(N)
GND
LOGIC
GND
P2-01AC
Power Hookup
Grounding
A good common ground reference (earth ground) is essential for
proper operation of the Productivity2000 system. One side of all
control circuits, power circuits and the ground lead must be properly
connected to earth ground by either installing a ground rod in close
proximity to the enclosure or by connecting to the incoming power
system ground. There must be a single-point ground (i.e. copper bus
bar) for all devices in the enclosure that require an earth ground.
3
Sales 800-633-0405 www.productivity2000.com
General Specifications
Operating Temperature 0º to 60ºC (32º to 140ºF)
Storage Temperature -20º to 70ºC (-4º to 158ºF)
Humidity 5 to 95% (non-condensing)
Environmental Air No corrosive gases permitted
Vibration IEC60068-2-6 (Test Fc)
Shock IEC60068-2-27 (Test Ea)
Enclosure Type Open Equipment
Agency Approvals UL508 File E139594, Canada & USA
CE (EN61131-2*)
Voltage Withstand
(dielectric) 2100VDC applied for 2 seconds
Insulation Resistance >10 MΩ @ 500VDC
Module Location Power Supply slot in a Productivity2000 System.
EU Directive
See the “EU Directive” topic in the Productivity Suite
Help File. Information can also be obtained at:
www.productivity2000.com
Weight 294g (10.4 oz)
User Specifications
Input Voltage Range (Tolerance) 100 to 240VAC (-15% / +10%)
Rated Operating Frequency 50 to 60Hz with ±5% tolerance
Maximum Input Power 37.4 W
Cold Start Inrush Current 23.6 A
Maximum Inrush Current (Hot Start) 25.6 A
Input Fuse Protection (Internal) Micro fuse 250V, 1A
Non-replaceable
Efficiency 75%
Output
UL Rated:
24VDC, 0.85 A
3.3 VDC, 3.81 A
Maximum Output Power 29W Combined
Heat Dissipation 8.4 W
Isolated User 24VDC Output None
Output Protection for Over Current,
Over Voltage, and Over Temperature Self resetting for both voltage outputs to base
Under Input Voltage Lock-out 55-65 VAC
Over Input Voltage Lock-out 265-280 VAC
Input Transient Protection Varistor, plus input choke and filter
Operating Design Life 10 years at full load at 40°C ambient and
5 years at 60°C ambient
*Meets EMC and Safety requirements. See the D.O.C. for details.
IMPORTANT! Important Hot-Swap Information
Note: This device cannot be Hot Swapped.
4Tech Support 770-844-4200www.productivity2000.com
Document Name Edition/Revision Date
P2-01AC-DS 1st Ed., Rev A 4/27/2016
Copyright 2016, AutomationDirect.com Incorporated/All Rights Reserved Worldwide
Altri manuali Automationdirect.com Alimentazione elettrica
