AUXO CENOTE Manuale utente
CENOTE USER MANUAL
READ THIS MANUAL BEFORE USING THE PRODUCT.
FAILURE TO FOLLOW INSTRUCTIONS AND SAFETY
PRECAUTIONS IN THIS MANUAL CAN RESULT IN
SERIOUS INJURY OR DEATH.
FOR EASY FUTURE REFERENCE, DOWNLOAD AND
SAVE THIS USER MANUAL AND WARRANTY POLICY.
DOWNLOAD THIS MANUAL AT:
www.auxo-official.com/pages/download
*Each glass piece is hand blown and may vary slightly in shape and size.
What’s in the Box
Type-C to Type-C
Charging Cable x 1 Cotton Swab x 5
x 5
20W Charging
Adapter x 1 User Manual x1
Silicone Rod Seal x 2
Glass Nozzle x 1
Ceramic Nail x 5 Tweezer x 1
Loading Tool x 1
Carb Cap x 1
Cenote Base x 1 Glass Mouthpiece* x 1
QUICK START
It is recommended to fully charge the device before first use.
Twist and lift the glass mouthpiece from the Cenote base to expose the heating rod.
Place ceramic nail into the center of the heating rod. To ensure contact with the heat sensor, press nail
firmly to the bottom.
Remove the glass nozzle from the mouthpiece and fill water from the pipe. Avoid filling water while
the mouthpiece is still attached to the base
Secure the glass nozzle and twist the water-filled mouthpiece back on the base. The pipe will face
the button when seated correctly
Lift the carb cap from the mouthpiece and load concentrates into the ceramic nail with the loading
tool. Secure the carb cap back in place. For best performance, 10-20mg of material is recommended
(about the size of a lentil).
1.
2.
3.
4.
5.
6.
Fill the mouthpiece
with water from the pipe
Water line
p
Tip: Do not overfill the ceramic nail.
Turning On/Off the Device
To turn on/off the device, long press the button for 3 seconds. Cenote will make a short vibration
and illuminate in red and yellow to indicate command success.
If no activity is detected for 10 minutes or longer, Cenote will turn off automatically.
If the battery temperature is over 149±34°F(65±1°C), the light on the button will blink in red 8
times and the device will implement overheat protection and suspend usage temporarily.
●
●
●
Tip: To prevent overheating, it is recommended to wait for 5 minutes after 3 consecutive sessions before
using again.
Setting Up The Device
There are 4 settings; short-press the button to choose between temperature options 1-3. Setting 4
is the Pro Mode, a tailor-made experience for the connoisseurs, controlled via the AUXO Connect app.
It is recommended to cycle through the settings first before starting the session to get familiarized
with the setting indications. For setting details, see next section.
To start the session, select the desired setting and leave idle for 5s, it will proceed to the preheating
phase before starting the session.
When the session is over, Cenote will begin to cool down. The steady red light indication will gradually
dim out as the temperature drops.
Once the heating rod cools down to 140±34°F(60±1°C), Cenote will go into standby.
To terminate mid-session, short-press the button to exit. The device will go into standby.
1.
2.
3.
4.
5.
The current session reaches the 20s countdown, or
The session ends and goes into cool down.
●
●
*Default temperature and duration of setting 4 (Pro Mode) is identical to setting 3 until adjustments are made on the AUXO Connect app.
Session Extension
All settings are eligible for a 20s session extension; double press the button for an additional 20s of
enjoyment when:
Heat Settings
Settings 1-3 can be controlled on the device itself whereas setting 4, the Pro Mode, is controlled via the
AUXO Connect app*
Repeat action to extend again.
Temperature
3
80s
4-PRO MODE
20s-90s40s
1 2
40sSession Duration
626°F
(330°C)
392 - 644°F
(200-340°C)
518°F
(270°C)
572°F
(300°C)
Heat Settings
Lighting
LED Indications
Lighting Indications
In-Session Lighting Effect Options
Controlled via the AUXO Connect app.
Preheating
(Deck light)
Standby
(Base light)
Bluetooth
(Connected)
Cool down
Steady red, gradual dim out
Short circuit protection Nail error Low battery Overheat protection
Aurora Purple Haze
Lumino (Default) UFO Lava
Cranberry Vodka
x2 x4 x6 x8
Due to safety concerns, Cenote is not operable while charging.
To charge the device, connect one end of the charging cable to the device and the other to the charging
adapter. Cenote also supports wireless charging; any Qi-certified wireless chargers are compatible.
Charging via the AUXO 20W power adapter takes approx. 1.5 hours for a full charge. Every full charge
generates approx. 12 sessions usage (calculation based on 100s sessions).
When the battery is depleted, the button will blink in red 6 times before powering off.
*Precaution: Should there be water in the mouthpiece, avoid tilting the device when checking the battery level.
10-30% 30-60% 60-80% 80-100%
Charging & Battery Level
●
●
●
●
Battery Level Indication
To check the battery level, press the button 3 times consecutively*; the base light will indicate the
battery level. Alternatively, you can find the precise battery level in the AUXO Connect app.
10% and below: button
blinks in red 6 times before powering off.
AUXO Connect App
If you're having trouble pairing Cenote with your phone, ensure the following:
Pairing
Turn on Bluetooth on your phone and place the device near your phone.
When the device is found, select accordingly. The LED light will blink in blue when paired successfully.
If the connection is unsuccessful, restart the app and try connecting again.
1.
2.
3.
Your AUXO Connect app is up to date.
Your device is turned on (restart if necessary).
The Bluetooth on your phone is turned on.
The device is near your phone (as close as possible).
1.
2.
3.
4.
AUXO Connect
Control Panel
(Left to right)
Row 1 - heat setting,
temperature adjustment,
session duration, lighting effect.
Row 2 – Session extension,
lighting effect extension.
Heat Setting
Scroll the setting bar to select your preferred option between
settings 1-3 or Pro Mode.
Lighting Extension
To keep the lighting effect on after the session, turn on the
extension switch to activate.
Temperature Adjustment
Only available to Pro Mode. For settings 1-3, the setting’s
temperature will be displayed.
Session Duration
Only available to Pro Mode, between 20s and 90s. For settings 1-3,
the setting’s duration will be displayed; session extendable by
turning on the extension switch beneath.
Lighting Effect
Effects controlled in the control panel will reflect directly on your
device as you start your session.
Session Extension
Assess the flavor of your material after every session. Extend
session for an extra 20 seconds by turning on the session
extension switch to activate. Not applicable to Pro Mode
+20s
Indice
Altri manuali AUXO Vaporizzatore
