AV-GAD EasyLoader AV-706 Manuale utente
AV-706 & AV-701 Keypads
INSTALLATION INSTRUCTIONS Item 4713 (A5DS)
Description
The AV-706 and AV-701 are 4-wire Remote Control Station and Programmer Keypad compatible
with EasyLoader Control Panels. AV-706 fits the Dublo & PRO alarm panels.
The AV-706 and AV-701 keypads are easy to install and operate. Large 7-Segment (AV-701) and
high-contrast LCD (AV-706) display provides vivid readout for all control panel’s information and
zone identification. For AV-706 model refer to the programming and setup manual.
Installation Instructions Press Down firmly on both tabs and pull
Handle keypad with clean hands
Do not use unnecessary force in opening
and closing the keypad
Pill off the protective sheet from upper
panel after the installation is complete
Step One: Opening the keypad
Locate the two rectangular tabs on the top
of the keypad (about 35 mm / 1.5 inches
from each side). Press down on both tabs
firmly and pull front panel of keypad
toward you from the top (see Figure 1.)
Step Two: Mounting onto Wall Fi gu r e 1: Open i ng t h e k eypad
Place the keypad on wall, at 1.5-1.8 meters height. Make sure the two “UP” arrows word,
are upwards. Attach housing to wall with flat-head screws (use screws that are suitable for
the wall material).
Before affixing to wall, make sure all wires have been inserted through the opening in the
rear housing. If wires come up from the floor, they may be inserted through the square
slot on the left side of the rear housing. (Use a small screwdriver for opening the slot with a
twisting action.)
Step Three: Wiring
Disconnect AC and Battery power before wiring. Insert wires through the opening in the
rear housing. (Note maximum wire lengths in the following table. The AV-706 keypad
maximum wiring length is 200 meters.) Make sure keypad wires are as far away as possible
from telephone and high power radio transmitter or other electrically “noisy” wires or
appliances. For longer run distance use thicker wire, e.g. 1 mm2.
It is recommended to run keypad wires separately in a 4 or 6 wire cable. Do not run
telephone, sensors or main electric wires in the same cable or electric pipe.
Keypad
Function
Alarm Panel Wire Terminals
Terminal
AV-2016
AV-2004/48
AV-3004/48
AV-2008
OR
Data
OR
OR
OR
OR
YE
Strobe
YE
YE
YE
YE
+12V
+ Power
+12V
+12V
+12V
+12V
-12V
- Power
-V
-V
-V
-V
Max. Cable (6 x 0.5 mm) length
150 meters
100 meters
100 meters
150 meters
*
7
4
1
0
8
5
2
#
9
6
3
Siren
Shunt
Display Status
Delay
Delete Chime
Test Program Reset
Shunt
Telephone
ARMED STATUS SHUNT FIRE
ZONE
DISPLAY
EASYLOADER AV-701
AV-GAD
Wire Terminal
Cut to disable buzzer
Installation Instructions AV-706 & AV-701
Step Four (optional): Connecting more than one keypad
For connecting more than one keypad to the same control panel, first refer to the “Control
Panel Manual” for maximum keypads allowance. Connect all keypads in parallel to the
control panel, by running wires from each keypad directly to control panel. Don’t run wires
from one keypad to another and then to control panel – this wiring way cause problems.
Step Five: Closing the keypad
Before closing, check the keypad(s) to make sure they operate properly, arrange wires to be
compact as possible at the rear housing, left side.
To connect the front keypad to mounted part, fit the two lower slots (note 2 at fig.2) onto the
two protruding tabs on the mounted bottom part, push front part forward and press firmly
until top slots and tabs snap together. Make sure that all sides are securely closed.
Note: There are two additional small tabs on upper and lower inner sides of the housing. These
tabs ensure tighter closure. However, if you encounter difficulty in closing the unit,
you can cut off the tabs (note 1 at fig. 2). This will release the closure.
Note 1: Two additional small tabs for tighten closure
Note 2: Fit the two slots onto the two protruding tabs
Back Illumination
The 706 and 701TI/701TIP keypads feature timed back
illumination. Two LED’s backlight dimly illuminates
the keypad’s key when keys are not active.
Pressing any key will increase brightness of backlight,
which will remain bright for about 10 seconds for
701TI/TIP and 60 seconds for all 706 keypads (after
last key is pressed). This feature requires no additional
wiring.
When keys are fully lit, current consumption rises
by 50 mA. AV-701TI current consumption with
dim lighting: 90 mA, AV-706 consumption: 130 mA.
Tamper Switch Fi gu r e 2: C l o s i n g t he k e yp a d
The models AV-701TIP and AV-706TP feature a tamper switch, which requires one additional
wire. Connect to TMP and -V on the wire terminal.
Wire the tamper to any zone programmed as Tamper, Day or 24H zone type. Upon opening the
keypad housing the tamper switch will activate the connected zone.
Ordering Information
AV-701TS: Semi - Illuminated keypad AV-706: LCD Illuminated keypad
AV-701TI: Timed Illuminated keypad AV-706TP: LCD Illuminated keypad + tamper
AV-701TIP: Timed Illuminated keypad + Tamper
Item 4713/W6/701INS_E4/ All rights reserved to Av-Gad Systems Ltd. May 2011
For operating and programming instructions,
please refer to your “Easyloader” operating and
installation manual.
AV-706 keypads are compatible only with PRO
& Dublo control panels.
Altri manuali per EasyLoader AV-706
1
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali AV-GAD Sistema di sicurezza
Manuali Sistema di sicurezza popolari di altre marche
EDM
EDM Solution 6+6 Wireless-AE Manuale utente
Highway Safety Group
Highway Safety Group EA401 Manuale utente
Siren
Siren LED GSM Manuale utente
Detection Systems
Detection Systems 7090i Istruzioni per il montaggio
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 Manuale utente
Siemens
Siemens FDM273 Manuale utente