avantec PH658N Manuale utente
Monday, 2 December 2013 PH658N - User Manual v1.1 1 15
Telephony I.P.
User Guide
PH658N
Trimline VoIP Telephone
General
-Standard configuration of 1 VoIP account. Maximum of 2 VoIP accounts
-Wideband G.722 Codec
-IPv / IPv6
-WAN port and LAN port
-Headset connectivity (check with your distributor for this option before order)
-PoE (check with your distributor for this option before order)
Server Compliance
-Asterisk / Broadsoft / Alcatel / NEC / Avaya basic call features supported
Codecs and Voice Features
-Wideband codec: G.722
-Narrowband codec: G.711µ/A, ILBC
-G.729
-VAD, CNG, AEC, PLC, AJB, AGC
-Full-duplex speakerphone with AEC
Monday, 2 December 2013 PH658N - User Manual v1.1 2 15
Installation
1. Unpack the box and check for the following items enclosed:
a. Main unit with built-in magnetic hook switch
b. Handset
c. Handset cord
d. RJ45 Ethernet cable
2. Connect the handset to the base unit using the coiled handset cord provided
3. Connect one end of the Ethernet cable to the WAN port of the main unit, and the other end
to the wall Ethernet outlet
To discover the IP address of the handset
1. Lift the handset
2. Hear the dial tone
3. Press * 1 2 3 4 5 #
4. Listen to the IP address being announced by the handset receiver
Keypad Mapping
Figure 1 – PH658N Keypad & LED mapping
Monday, 2 December 2013 PH658N - User Manual v1.1 3 15
Call Operation
A. Initiating a Call
1. Lift the handset.
2. Listen to dial tone.
3. Press the desired number on the keypad and wait for 5 second or press “#” to dial out.
4. To end the call, place the handset back on the cradle in the base unit.
B. Answering a Call
An incoming call to the phone.
An audible ringing sound to alert the user.
LED on the top right corner flashes.
1. Lift up the handset to answer the call.
2. To end the call, place the handset back on the cradle. The LED will turn off.
C. Redial
There is no redial function on this model
D. Speakerphone Volume
1. Press speakerphone button
2. Press the Vol+ or Vol- button to increase or decrease the speakerphone volume
3. Observe the volume bar shown on the LCD
Alternatively, go on to the Web Portal, go to Phone Settings page and adjust the volume
settings (see Figure 2).
E. Ringer Volume
1. Go on to the Web Portal, go to Phone Settings page and adjust the volume settings (see
Figure 2).
Figure 2 - Phone Settings Page on Web Portal
Monday, 2 December 2013 PH658N - User Manual v1.1 4 15
F. Call Flash
1. During a conversation using the handset, press the FLA H button.
2. The previous conversation is automatically put on-hold.
3. Listen for dial-tone coming from the handset receiver.
4. To place another call, simply press the desired number on the keypad and wait for 5
seconds or press "#" to dial out immediately.
G. Call Hold
1. During a conversation using the handset, press the HOLD button.
2. The other end of the call is now put on-hold. Hold music is generated by the PBX to the
other end.
3. To deactivate the call-hold, press the HOLD button again.
H. Mute
1. During a conversation, press the MUTE button
2. The other end is not able to hear you but you can continue to hear from the other end.
3. To deactivate Mute, press the MUTE button again.
Monday, 2 December 2013 PH658N - User Manual v1.1 5 15
I. Programmable Memory Button and Emergency Call Number
PH658N has 2 programmable memory buttons:
1) The first one is the one-touch memory button on the faceplate.
To activate, lift the handset and simply press it once. The number will be dialed out
immediately.
2) The other corresponds to the preconfigured number for emergency call.
To activate, lift the handset and wait for a predetermined number of seconds. The number
will be dialed out automatically
Storing a number for hotkey and emergency call
1. Access the Web Portal, go to the Configuration page
2. Fill in the entries for Memory key, Emergency Call Number and Emergency Call Timeout
(see below)
3. Remember to press save, at the bottom of the page, when you are done.
Figure 3 - Memory Key and Mailbox Key setting on Web Portal
Monday, 2 December 2013 PH658N - User Manual v1.1 6 15
J. Message Light LED (MWI)
When a message is received at the voicemail box, the LED on the back of the handset goes up
and flashes periodically.
The mailbox access number can be programmed to the memory key. Refer to Section I -
Programmable Memory Key and Emergency Call. When it is configured properly, users can lift up
the handset and press the memory key to access the mailbox.
K. Call Waiting
1. During a conversation, when there is another incoming call, press flash to receive that call.
2. The previous party is put on-hold automatically.
3. To end the second call, place the handset back on the cradle.
4. The LED on the back of the handset stays ON to remind users that the previous call is still on
the line.
5. To retrieve the previous call, lift up the handset and press Line 1 or Line 2 (depending on
which line is used in Step 1).
Monday, 2 December 2013 PH658N - User Manual v1.1 7 15
Web Portal
The Web Portal of PH658N can be accessed by Google Chrome, Internet Explorer and Mozilla
Firefox.
A. To Log in
Enter http://< IP Address of the handset > on the browser.
Login name and password are as follows,
username : avantec
password : 1234
The welcome page shows the hardware version and firmware date code of the model (see below).
Figure - Welcome page of the Web Portal
(A.1) Logout
When done, remember to logout completely.
Clear the cache / cookie of your web browser so that the previous login is not re-cycled by the next
user.
Monday, 2 December 2013 PH658N - User Manual v1.1 8 15
B. To set login password for Web Portal
It is recommended for administrators to change login name and password to enhance security.
1. Click on the “Admin” link at the top right corner of the page
2. On the left panel, find the "Set Password" link and press on it.
3. Enter username for login name
4. Enter password and re-enter for confirmation purpose
5. When the mask password box is checked, both password entries are masked. To un-mask,
simply un-checked the mask password box.
Figure 5 - Set Password for accessing the Web Portal
Monday, 2 December 2013 PH658N - User Manual v1.1 9 15
C. Network Settings
Administrators may choose to operate in either dynamic IP environment and static IP environment.
1. Go to Configuration page.
2. On the left panel, click on the "Network / Print Log Settings" link
3. After making changes, click save at the bottom of the page
4. A pop-up window appears, you may choose between "back" and "restart"
5. In order to have the changes take effect immediately, click "restart"
6. You can always perserve the changes and decide to restart the phone at a later time
Figure 6 - Network Settings page on Web Portal
Monday, 2 December 2013 PH658N - User Manual v1.1 10 15
D. SIP Account Settings
Parameters for Session-initiation-protocol (SIP) such as registrar address, proxy address, port etc.
can be found in the "SIP Accounts" section on the Configuration page.
1. Go to Configuration page
2. On the left panel, under "SIP Accounts", click on the "Account 1" link
3. Enter the SIP registration particulars for Account 1
Note that you have the flexibility of registering to one server per account
4. When done, click Save
5. The changes take effect immeidately
6. Proceed to complete the entries for Account 2 and Account 3
Figure 7 - Account Settings page on Web Portal
Parameters for Call settings for each account can be found under the title, "Call Settings", on the
left panel.
Such parameters include:
-Call Forward Mode
-Call Waiting activation / deactivation
-DND activation / deactivation
-Auto-Answer activation / deactivation
Parameters for Audio settings for each account can be found under the title, "Audio Settings", on
the left panel.
Such parameters include:
-DTMF mode (in-band / RFC2833 / SIP INFO)
-Audio Codec preference (PCMU / PCMA / G.722 / G.729 / iLBC)
-ToS
-Jitter
Indice
Altri manuali avantec Telefono IP
