Avanti 57568 Istruzioni per il montaggio
RETURNS NOT ACCEPTED
& WARRANTY VOID
if Sprayer is not properly cleaned
immediately after every use.
Clean Sprayer immediately after
use to prevent permanent damage.
Visit our website at: http://www.harborfreight.com
Email our technical support at: [email protected]
Owner’s Manual & Safety Instructions
Save This Manual Keep this manual for the safety warnings and precautions, assembly,
operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the
back of the manual near the assembly diagram (or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference. 21d
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
Copyright© 2020 by Harbor Freight Tools®. All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly an d se rv ic e may n ot b e in cl uded.
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Page 2 For technical questions, please call 1-888-866-5797. Item 57568
RETURNS NOT ACCEPTED & WARRANTY VOID
if Sprayer is not properly cleaned immediately after every use.
Clean Sprayer immediately to prevent permanent damage.
SAFETY OPERATION MAINTENANCESETUP
Table of Contents
Safety .......................................................................2
Specifications ...........................................................8
Setup ........................................................................9
Operation .................................................................11
Maintenance ............................................................16
Parts List and Diagram ............................................22
Warranty ..................................................................24
WARNING SYMBOLS AND DEFINITIONS
This is the safety alert symbol. It is used to alert you to potential
personal injury hazards. Obey all safety messages that
follow this symbol to avoid possible injury or death.
Indicates a hazardous situation which, if not avoided,
will result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury.
Addresses practices not related to personal injury.
IMPORTANT SAFETY INSTRUCTIONS
1. SAVE THESE INSTRUCTIONS – To reduce the
the injury to persons, read and understand all
instructions included in this manual. Be familiar with
the controls and the proper usage of the equipment.
2.
a.
as cigarettes, motors, and electrical equipment.
b. For units intended for use with only
water-based or mineral spirit-type materials
– Do not spray or clean with liquids having
c.
is able to result in static electricity. Static
in the presence of paint or solvent fumes.
All parts of the spray system, including
the pump, hose assembly, spray gun, and
objects in and around the spray area shall be
properly grounded to protect against static
discharge and sparks. Use only conductive or
grounded high-pressure airless paint sprayer
d. Verify that all containers and collection systems
are grounded to prevent static discharge.
e. Connect to a grounded outlet and use grounded
f. Do not use a paint or a solvent
containing halogenated hydrocarbons.
See operating instructions for examples
of these types of materials.
g. Keep spray area well ventilated. Keep a good
supply of fresh air moving through the area.
Keep pump assembly in a well ventilated
area. Do not spray pump assembly.
h. Do not smoke in the spray area.
i. Do not operate light switches, engines, or similar
spark producing products in the spray area.
j. Keep area clean and free of paint or solvent
For technical questions, please call 1-888-866-5797.Item 57568
RETURNS NOT ACCEPTED & WARRANTY VOID
if Sprayer is not properly cleaned immediately after every use.
Clean Sprayer immediately to prevent permanent damage.
SAFETYOPERATIONMAINTENANCE SETUP
k. Know the contents of the paints and solvents
being sprayed. Read all Material Safety Data
Sheets (MSDS) and container labels provided
with the paints and solvents. Follow the paint
l. Fire extinguisher equipment shall
be present and working.
a. Do not aim the gun at, or spray
any person or animal.
b. Keep hands and other body parts away
from the discharge. For example, do not try
to stop leaks with any part of the body.
c. Always use the nozzle tip guard. Do not
spray without nozzle tip guard in place.
d.
by the manufacturer.
e. Use caution when cleaning and changing nozzle
tips. In the case where the nozzle tip clogs while
for turning off the unit and relieving the pressure
before removing the nozzle tip to clean.
f. Do not leave the unit energized or under
pressure while unattended. When the unit is not
in use, turn off the unit and relieve the pressure in
g. High-pressure spray is able to inject toxins
into the body and cause serious bodily
injury. In the event that injection occurs,
seek medical attention immediately.
h. Check hoses and parts for signs of damage.
Replace any damaged hoses or parts.
i.
Only use replacement parts or accessories
j. Always engage the trigger lock
when not spraying. Verify the trigger
lock is functioning properly.
k. Verify that all connections are secure
before operating the unit.
l. Know how to stop the unit and bleed pressure
quickly. Be thoroughly familiar with the controls.
4.
a. Always wear appropriate gloves, eye protection,
and a respirator or mask when painting.
b. Do not operate or spray near children. Keep
children away from equipment at all times.
c. Do not overreach or stand on an
unstable support. Keep effective
footing and balance at all times.
d. Stay alert and watch what you are doing.
e. Do not operate the unit when fatigued or
f. Do not kink or over-bend the hose.
g. Do not expose the hose to temperatures
or to pressures in excess of those
h. Do not use the hose as a strength
member to pull or lift the equipment.
Work Area
1. Keep the work area clean and well lighted.
Cluttered benches and dark areas increase the
risks of electric shock, fire, and injury to persons.
2. Operate only in a well-ventilated area.
Paint thinners and solvents may
be harmful if inhaled.
Do not operate the sprayer in explosive
atmospheres, such as in the presence of
flammable liquids, gases, or dust.
The sprayer is able to create sparks resulting
in the ignition of the dust or fumes.
4. Keep bystanders, children, and visitors away
while operating the tool. Distractions are
able to result in the loss of control of the tool.
Page 4 For technical questions, please call 1-888-866-5797. Item 57568
RETURNS NOT ACCEPTED & WARRANTY VOID
if Sprayer is not properly cleaned immediately after every use.
Clean Sprayer immediately to prevent permanent damage.
SAFETY OPERATION MAINTENANCESETUP
Electrical Safety
1. Sprayer plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with grounded sprayers.
Unmodified plugs and matching outlets
will reduce risk of electric shock.
2. Avoid body contact with grounded surfaces
such as pipes, radiators, ranges and
refrigerators. There is an increased risk of
electric shock if your body is grounded.
Do not expose sprayers to rain or wet
conditions. Water entering a sprayer will
increase the risk of electric shock.
4. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the sprayer.
Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled
cords increase the risk of electric shock.
5. When operating a sprayer outdoors, use
an extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use
reduces the risk of electric shock.
6. If operating a sprayer in a damp location
is unavoidable, use a Ground Fault Circuit
Interrupter (GFCI) protected supply.
Use of a GFCI reduces the risk of electric shock.
Personal Safety
1. Stay alert. Watch what you are doing and
use common sense when operating the tool.
Do not use the tool while tired or under the
influence of drugs, alcohol, or medication.
A moment of inattention while operating the
tool increases the risk of injury to persons.
2. Dress properly. Do not wear loose clothing
or jewelry. Contain long hair. Keep hair,
clothing, and gloves away from moving parts.
Loose clothes, jewelry, or long hair increases
the risk of injury to persons as a result
of being caught in moving parts.
Avoid unintentional starting. Be sure the
trigger is off before connecting to the
power supply. Do not carry the sprayer with
your finger on the trigger or connect the sprayer
to the power supply with the trigger on.
4. Do not overreach. Keep proper
footing and balance at all times.
Proper footing and balance enables better
control of the tool in unexpected situations.
5. Use safety equipment.
Wear protective paint spraying
gloves and a NIOSH-approved
respirator during use.
Non-skid safety shoes and a hard
hat must be used for the applicable conditions.
6. Always wear eye protection.
Wear ANSI-approved safety goggles.
Tool Use and Care
1. Do not force the tool. Use the correct tool
for the application. The correct tool will do the job
better and safer at the rate for which
it was designed.
2. Do not use the sprayer if the switch does
not turn it on and off. Any sprayer that cannot
be controlled with the switch is dangerous and
must be repaired.
Disconnect the tool from the power
source before making any adjustments,
changing accessories, or storing the tool.
Such preventive safety measures reduce the
risk of starting the tool unintentionally.
4. Store the tool when it is idle out of reach
of children and other untrained persons.
A tool is dangerous in the hands of untrained users.
Page 5For technical questions, please call 1-888-866-5797.Item 57568
RETURNS NOT ACCEPTED & WARRANTY VOID
if Sprayer is not properly cleaned immediately after every use.
Clean Sprayer immediately to prevent permanent damage.
SAFETYOPERATIONMAINTENANCE SETUP
5. Check for misalignment or binding of moving
parts, breakage of parts, and any other condition
that affects the tool’s operation. If damaged,
have the tool serviced before using. Many accidents
are caused by poorly maintained tools. There
is a risk of bursting if the tool is damaged.
6. Use only accessories that are identified by the
manufacturer for the specific tool model. Use of
an accessory not intended for use with the specific
tool model, increases the risk of injury to persons.
Service
1. Tool service must be performed only
by qualified repair personnel.
2. When servicing a tool, use only identical
replacement parts. Use only authorized parts.
Use only lubricants supplied with the
tool or specified by the manufacturer.
Specific Safety Instructions
1. INJECTION HAZARD!
Although this paint gun is airless,
it still puts out paint at a very high
pressure. Through improper use,
paint can be injected through a person’s skin, leading
to serious injury, possibly amputation. If paint is
accidentally injected into someone’s skin, contact a
doctor immediately. Do not treat an injection injury
as a simple cut. Injection can lead to amputation
and requires immediate surgical treatment.
2. Do not direct spray at people or animals. Do
not place your hand in front of Spray Gun’s
nozzle or attempt to deflect paint spray
with your hand during use. Gloves and
clothing don’t offer adequate protection
from toxic paints, sealers, or stains.
Do not spray flammable materials in vicinity
of open flame or near ignition sources.
Motors, electrical equipment, and controls
can cause electrical arcs that will ignite a
flammable gas or vapor. Do not store flammable
liquids or gases in vicinity of this unit.
4. Do not come into contact with a fluid stream
created by a leak in the paint hose.
5. Do not leave Paint Sprayer pressurized
while unattended.
6. Do not clean Spray Gun tip while it
is still connected to paint hose.
7. Keep the trigger and the electrical
cord plug clean and paint-free.
8. Do not run Paint Sprayer while empty.
Damage to the unit may occur.
9. Do not use Paint Sprayer to spray
asbestos, metallic paints, glazes, red lead,
cement, ground chalk, abrasive grainy
paints containing lime, or bleach.
These will damage the spray gun
and void the warranty.
10. Read all of the information concerning coating
products and cleaning solvents. Do NOT use
bleach, low-flash naphthalene, acetone, alcohol or
toluene when cleaning Paint Sprayer equipment.
11. Do not use bleach or halogenated hydrocarbon
bromine, carbon tetrachloride, and ethyl iodide).
Long term exposure to many chlorinated
hydrocarbons through inhalation can result in liver
and kidney toxicity. Exposure of unprotected skin
to the solvents used can cause defatting of the
skin resulting in dermatitis. Methylene chloride
and vinyl chloride have also been shown to be
human carcinogens. Some of these solvents are
flammable. Welding operations near the these
materials can create phosgene, a highly toxic gas.
12. Many spray guns contain aluminum,
which reacts strongly to chlorinated solvents.
Contact the solvent or coating manufacturer as
needed regarding potential chemical reactions.
Industrial applications must follow
OSHA requirements.
14. Spraying hazardous materials may result in serious
injury or death. Do not spray pesticide, acid,
corrosive material, fertilizer, or toxic chemicals.
Page 6 For technical questions, please call 1-888-866-5797. Item 57568
RETURNS NOT ACCEPTED & WARRANTY VOID
if Sprayer is not properly cleaned immediately after every use.
Clean Sprayer immediately to prevent permanent damage.
SAFETY OPERATION MAINTENANCESETUP
15. Paints and solvents may be harmful or fatal if
swallowed or inhaled. Avoid prolonged skin
contact with solvents or paints as they will
irritate skin. After any contact, immediately
wash off exposed area with hot, soapy water.
16. Keep paint hose away from sharp objects.
Bursting hoses may cause injury.
Examine hoses regularly and replace if damaged.
17. When flushing Paint Sprayer system,
use lowest possible pressure setting.
18. All hoses and spray gun accessories
used with Paint Sprayer must be pressure
19. The Paint Sprayer must be plugged into
an outlet that is grounded in accordance
with all local codes and ordinances.
20. Use caution while spraying on windy days.
21. Do not use Paint Sprayer without the
Spray Gun’s nozzle guard in place.
22. Paint Sprayer’s housing may become
hot during use. Do not touch housing
until it has completely cooled.
Remove Spray Tip or turn to cleaning position
BEFORE cleaning or flushing Paint Sprayer system.
24. Do not use pliers to tighten or loosen
high pressure connections.
25. Sparks from improper grounding
can ignite fumes!
Follow all local regulations regarding
the use of fluid supply containers
and solvent pails used with flushing the Paint
Sprayer. Use only conductive metal pails placed on
a grounded (concrete) surface. Do not place pails
on nonconductive surfaces (such as cardboard or
paper). Ground all metal pails by clamping one end
of a ground wire to the pail and the other end to a
grounded structure (such as a nearby pipe).
Maintain grounding, even when flushing or relieving
pressure from Paint Sprayer into metal pail.
The force of the spray can knock a metal pail over,
so hold down the metal pail and keep the metal
part of the spray gun set against the grounded
metal pail when pressing the spray gun trigger.
26. Maintain labels and nameplates on the sprayer.
These carry important safety information.
If unreadable or missing, contact
Harbor Freight Tools for a replacement.
27. People with pacemakers should consult their
physician(s) before use. Electromagnetic fields in
close proximity to heart pacemaker could cause
pacemaker interference or pacemaker failure.
SAVE THESE INSTRUCTIONS.
Grounding
TO PREVENT ELECTRIC SHOCK AND DEATH FROM
INCORRECT GROUNDING WIRE CONNECTION:
Check with a qualified electrician if you are in doubt as to whether the outlet is properly
grounded. Do not modify the power cord plug provided with the tool. Never remove the
grounding prong from the plug. Do not use the tool if the power cord or plug is damaged. If damaged, have
it repaired by a service facility before use. If the plug will not fit the outlet, have a proper outlet installed by
a qualified electrician.
Page 7For technical questions, please call 1-888-866-5797.Item 57568
RETURNS NOT ACCEPTED & WARRANTY VOID
if Sprayer is not properly cleaned immediately after every use.
Clean Sprayer immediately to prevent permanent damage.
SAFETYOPERATIONMAINTENANCE SETUP
Grounded Tools: Tools with Three Prong Plugs
3-Prong Plug and Outlet
1. Sprayers marked with “Grounding Required”
have a three wire cord and three prong grounding
plug. The plug must be connected to a properly
grounded outlet. If the sprayer should electrically
malfunction or break down, grounding provides
a low resistance path to carry electricity away
from the user, reducing the risk of electric
shock. (See 3-Prong Plug and Outlet.)
2. The grounding prong in the plug is connected
through the green wire inside the cord to the
grounding system in the sprayer. The green
wire in the cord must be the only wire connected
to the sprayer’s grounding system and must
never be attached to an electrically “live”
terminal. (See 3-Prong Plug and Outlet.)
The sprayer must be plugged into an appropriate
outlet, properly installed and grounded in
accordance with all codes and ordinances. The plug
and outlet should look like those in the preceding
illustration. (See 3-Prong Plug and Outlet.)
Extension Cords
1. Grounded sprayers require a three
wire extension cord. Double Insulated sprayers
can use either a two or three wire extension cord.
2. As the distance from the supply outlet increases, you
must use a heavier gauge extension cord. Using
extension cords with inadequately sized wire causes
a serious drop in voltage, resulting in loss of power
and possible sprayer damage. (See Table A.)
The smaller the gauge number of the wire, the
greater the capacity of the cord. For example,
a 14 gauge cord can carry a higher current
than a 16 gauge cord. (See Table A.)
4. When using more than one extension cord
to make up the total length, make sure
each cord contains at least the minimum
wire size required. (See Table A.)
5. If you are using one extension cord for more
than one sprayer, add the nameplate amperes
and use the sum to determine the required
minimum cord size. (See Table A.)
6. If you are using an extension cord outdoors, make
sure it is marked with the suffix “W-A” (“W” in
Canada) to indicate it is acceptable for outdoor use.
7. Make sure the extension cord is properly wired
and in good electrical condition. Always replace
a damaged extension cord or have it repaired
by a qualified electrician before using it.
8. Protect the extension cords from sharp objects,
excessive heat, and damp or wet areas.
RECOMMENDED MINIMUM WIRE GAUGE
FOR EXTENSION CORDS* (120/240 VOLT)
NAMEPLATE
AMPERES
(at full load)
EXTENSION CORD
LENGTH
25’ 50’ 75’ 100’ 150’
0 – 2.0 18 18 18 18 16
18 18 18 16 14
18 18 16 14 12
5.1 – 7.0 18 16 14 12 12
7.1 – 12.0 18 14 12 10 -
12.1 – 16.0 14 12 10 - -
16.1 – 20.0 12 10 - - -
TABLE A
* Based on limiting the line volt-
age drop to five volts at 150% of
the rated amperes.
Page 8 For technical questions, please call 1-888-866-5797. Item 57568
RETURNS NOT ACCEPTED & WARRANTY VOID
if Sprayer is not properly cleaned immediately after every use.
Clean Sprayer immediately to prevent permanent damage.
SAFETY OPERATION MAINTENANCESETUP
Specifications
Electrical Input
Maximum Working Pressure
Spray Hose Outlet
TIP CHART
Oil-Based Water-Based
Tip
Size Stain Primer &
Enamel
Primer &
Stain
Interior
Paint
Exterior
Paint
Thick
Paint
X X X X
515 X X X X
517 X X X
519 X X X X
521 X
Symbology
Symbol Property or Statement
VVolts
~Alternating Current
AAmperes
PSI Pounds per square inch of pressure
CFM Cubic Feet per Minute flow
SCFM Cubic Feet per Minute flow
at standard conditions
NPT National pipe thread, tapered
NPS National pipe thread, straight
Symbol Property or Statement
WARNING marking concerning
Risk of Eye Injury.
Wear ANSI-approved eye protection.
WARNING marking concerning
Risk of Respiratory Injury.
Wear NIOSH-approved respirator.
WARNING marking concerning
Risk of Explosion.
WARNING marking concerning
Risk of Injection Injury.
Do not direct spray at hands
or body. Have injection injury
treated immediately.
WARNING marking concerning Risk
of Fire.
Do not use solvents improperly.
Page 9For technical questions, please call 1-888-866-5797.Item 57568
RETURNS NOT ACCEPTED & WARRANTY VOID
if Sprayer is not properly cleaned immediately after every use.
Clean Sprayer immediately to prevent permanent damage.
SAFETYOPERATIONMAINTENANCE SETUP
Setup – Before Use
Read the ENTIRE IMPORTANT SAFETY INFORMATION section
at the beginning of this manual including all text under subheadings therein
before set up or use of this product.
Note: For additional information regarding the parts listed in the following pages,
refer to the Assembly Diagram near the end of this manual.
Components and Controls
Spray
Hose
Outlet
Prime/Spray
Valve
Suction
Hose
Power
Cord
Hook
Priming
Hose
Power
Switch
Suction &
Priming Hose
Storage
Cup
Pressure
Knob
Page 10 For technical questions, please call 1-888-866-5797. Item 57568
RETURNS NOT ACCEPTED & WARRANTY VOID
if Sprayer is not properly cleaned immediately after every use.
Clean Sprayer immediately to prevent permanent damage.
SAFETY OPERATION MAINTENANCESETUP
Assembly
1. Attach Spray Hose
Attach Spray Hose to Spray Hose Outlet.
Tighten securely with included wrench.
Spray
Hose
Outlet
2. Install Filter in Spray Gun
a. For water-based paints, use
pre-installed 60 mesh coarse filter.
b. For oil-based paints, remove coarse filter and
install 100 mesh fine filter. Use proper Spray
Tip according to Tip Chart on page 8.
• Remove Handle from Spray Gun
with included wrench.
• Remove filter by turning it counterclockwise.
• Replace filter and reassemble Spray Gun.
Secure
wrench on
flat spots
Handle
Filter
Attach Spray Gun
Attach Spray Gun to Spray Hose. Tighten
securely with two included wrenches.
Indice
Altri manuali Avanti Spruzzatore di vernice
Avanti
Avanti 64933 Manuale utente
Avanti
Avanti 64934 Istruzioni per il montaggio
Avanti
Avanti 57042 Istruzioni per il montaggio
Avanti
Avanti 57042 Manuale utente
Avanti
Avanti 58149 Manuale utente
Avanti
Avanti AV-HVLP-5S Istruzioni per il montaggio
Avanti
Avanti 57641 Istruzioni per il montaggio
Avanti
Avanti 58056 Istruzioni per il montaggio
Avanti
Avanti 57042 Manuale utente
