Avaya G860 Manuale
Why the Avaya G860 Media Gateway
Avaya G860 Media Gateway Setup 03-601863, Issue 1, November 2007 1
Avaya G860 Media Gateway Setup
Why the Avaya G860 Media Gateway
The Avaya G860 Media Gateway allows call center customers to consolidate facilities and
reduce communications costs. The media gateway concentrates incoming PSTN traffic over
several DS3 lines while supporting VoIP telephony in the call center itself.
The use of voice over IP (VoIP) and conversion from DS1 to DS3 lines eliminate the large
number of DS1 interfaces required to support the same amount of call traffic. The Avaya G860
Media Gateway supports up to 6000 channels of session IP (SIP) VoIP telephony. It uses N+1
redundancy of media gateway, Ethernet switch, shelf controller, and power supply modules to
achieve high availability in mission critical applications.
In the sample call center configuration shown here, a simulated PSTN delivers customer calls
using a DS3 interface to the Avaya G860 Media Gateway. The media gateway establishes calls
with the Avaya S8720 Media Server via SIP signaling and routes all Real-time Transport
Protocol (RTP) traffic to the appropriate media resources within the Avaya G650 Media
Gateway or Avaya endpoints. Avaya Communication Manager delivers the calls to an agent
phone.
Sample configuration using the Avaya G860 Media Gateway
Customer
Phones
cyg860d1 LAO 091207
IP
Network SYSTEM
CRITICAL
MAJOR
MINOR
SHELF
ACO
PSU-5/30/DC
POWER
FAULT
HSR
POWER
SWAP
READY
FMR-5
PSU-5/30/DC
POWER
FAULT
PSU-5/30/DC
POWER
FAULT
ALARM
CONSOLE
CPC6600
24PORT
10/100/1000M
SWITCH
LINK SPEED
10/100M
RESET
ACT/LINK
SYSTEM FAULT
SPEED
ACT/LINK
SPEED
12
34
56
78
910
11 12
13 14
15 16
17 18
19 20
21 22
23 24
MGMT(MDI)
CompacIPCI
CONSOLE
CPC6600
24PORT
10/100/1000M
SWITCH
LINK SPEED
10/100M
RESET
ACT/LINK
SYSTEM FAULT
SPEED
ACT/LINK
SPEED
12
34
56
78
910
1112
13 14
15 16
17 18
19 20
2122
23 24
MGMT(MDI)
CompacIPCI
FAIL
ACT
LINK/
ACT
1 2
GBE PSTN
ABC
LINK
ALARM
LINK
ALARM
LINK
ALARM
ATM
1A
RX/TX
ALRM
2A
RX/TX
ALRM
3A
RX/TX
ALRM
1B
RX/TX
ALRM
2B
RX/TX
ALRM
3B
RX/TX
ALRM
IOIO
PWR
SWAP
READY
6310Series
FAIL
ACT
LINK/
ACT
1 2
GBE PSTN
ABC
LINK
ALARM
LINK
ALARM
LINK
ALARM
ATM
1A
RX/TX
ALRM
2A
RX/TX
ALRM
3A
RX/TX
ALRM
1B
RX/TX
ALRM
2B
RX/TX
ALRM
3B
RX/TX
ALRM
IOIO
PWR
SWAP
READY
6310Series
PMC
233
P
M
C
-
B
ACTIVITY
COM
RESET
READY
ALARM
USER
ABORT
HOT
SWAP
P
M
C
-
A
CP2300S-650
PMC
233
P
M
C
-
B
ACTIVITY
COM
RESET
READY
ALARM
USER
ABORT
HOT
SWAP
P
M
C
-
A
CP2300S-650
FANOR POWER FAIL
FANAND POWER OK
ACINPUT
DCINPUT
ACTIVERING
FANOR POWER FAIL
FANAND POWER OK
ACINPUT
DCINPUT
ACTIVERING
103 4 56 8 9Power 2711 12 13 Power114
Simplex Duplexch ch2
0
1
1
1
0
3
23
2
5
45
4
disc
COMPACT
UID
2
1
Simplex Duplexch ch2
0
1
1
1
0
3
23
2
5
45
4
disc
COMPACT
UID
2
1
Avaya S8720
Servers
Avaya G650
Media Gateway
Agent
Phones
EMS
Client
EMS
Server
Avaya G860
Media Gateway
SIP SIP T3
PRI
SNMP
PSTN
Management Platform
CD-RW
DVD
Avaya G860 Media Gateway Setup
2Avaya G860 Media Gateway Setup 03-601863, Issue 1, November 2007
Agents can also make outbound calls using the same network. In the sample configuration,
multiple TN799DP C-LAN circuit packs support alternate routing and permit load sharingof calls
delivered by the Avaya G860 Media Gateway.
What this document covers
This document focuses on the required equipment and the following administration steps for
configuring:
●A SIP trunk between the Avaya G860 Media Gateway and Avaya Communication
Manager
●Inbound and outbound call routing
●Load balancing of inbound traffic among multiple TN799DP C-LAN circuit packs.
●Alternate routing of inbound traffic when the C-LANs become inaccessible or are busied
out
●SNMP trap receivers to which the Avaya G860 Media Gateway reports alarms.
Needed equipment
The Avaya G860 Media Gateway is shipped with the following equipment:
●Avaya G860 Media Gateway, which at a minimum includes the following components:
-
Avaya G860 chassis
-
2 system controllers (Slots 1 & 2)
-
ES6600 Ethernet modules (Slots 3 & 4)
-
Console cable for system controller administration.
-
CD-ROM - Mediant 5000/8000 & EMS documentation.
●A Solaris UNIX-based Sunfire server for the Element Management System (EMS) server
software.
-
Preinstalled Solaris OS Version 9.0
-
1 Console cable for network administration
-
2 CD-ROMs - Solaris 9 Installation for EMS Server CD 1 & 2
-
1 DVD software Installation & Documentation 3.2.113 (media gateway software, EMS
client and server software).
Why the Avaya G860 Media Gateway
Avaya G860 Media Gateway Setup 03-601863, Issue 1, November 2007 3
In addition, the following equipment is also required:
●A Windows 2003 server for the EMS client software that is used for operations,
administration, management, and provisioning functions. This server is connected to the
Solaris server. A Windows 2000/XP computers are possible platforms for the EMS client.
Avaya Services has chosen the Windows 2003 server as its standard platform.
●Management platform to handle secure access and control if customer has a maintenance
contract with Avaya. For information on how to install and setup this computer, see Secure
Access and Control at http://support.avaya.com/sac/.
The customer supplies the following equipment:
●A standard 19-in. (48-cm) 4-post equipment rack that is properly installed and solidly
secured to EIA-310D or equivalent standards. A rack cabinet must have adequate
ventilation.
●DC power supply
●Power cable from gateway to DC power supply. Wiring needs to be stripped and
connectors attached on site.
●CAT5 Ethernet cable (gigabit)
●T3 cable to connect the Trunk Processing Modules (TPMs [TP6310]). This cable requires
a female SMB connector.
●Avaya S8720 Server with a DAL2 board installed, configured, and operating. Only
hardware duplication supports the Avaya G860 Media Gateway.
●Avaya G650 Media Gateway installed and operating. The media gateway must have an
adequate number of TN799DP C-LAN circuit packs and TN2302AP IP Media Processors
or TN2602AP IP Media Resource 320 circuit packs.
The Avaya G860 Media Gateway comes with
●Trunk Processing Modules (TPMs [TP6310])
●2 Shelf (system) control cards (SCCs)
●2 Ethernet switch boards
●Active and standby Rear Transition Modules (RTMs), DS-3 interfaces for TPMs
●2 SA/RTM for System Controllers, 2 RTM for TP6310 (Active/Redundant type depending
on configuration. The active TPM RTM has PSTN interfaces, and the redundant TPM does
not.
●Cable to DS3 line (50-ft [15 m] comes standard.
Other equipment and items:
●DS-3 broadband patch panel with associated monitoring patch panel jacks and cables
(recommended). The patch panel, collocated with the G860 Media Gateway, allows the
unobtrusive observation of incoming and outgoing traffic on the DS3 connection. Contact
your Avaya representative for details.
Avaya G860 Media Gateway Setup
4Avaya G860 Media Gateway Setup 03-601863, Issue 1, November 2007
●Laptop computer with EMS client installed for staging.
●Filled-out planning form with IP addresses. A blank planning form is available on http:/
support.avaya.com within the product documentation for G860 Media Gateway. IP
addresses are required for several items, including certain TN circuit packs, such as
C-LANs, MedPros, and VAL; network servers, such as DNS, NTP, and NMS; and certain
components on the G860 Media Gateway. The following table provides guidance on which
G860 items need IP addresses:
Laptop access for staging
If you are staging the Avaya G860 Media Gateway, make sure you have the following
equipment and applications available. For detailed information on staging, refer to the internal
Job Aid: Requirements for Staging G860 High Density Trunk Gateway R1 G860 HDTG.
●Laptop computer running Windows XP, service pack 2
●Internet Explorer, version 6.0 or higher.
●EMS client software
●Console cable for EMS server (Cable and serial adapter is shipped with EMS Sunfire
Server.)
●Console cable for the system controller (Cable and serial adapter is shipped with G860
Media Gateway)
G860 Slots Module IP Address/Mask
10 TP 6310-R
9 TP 6310
8 TP 6310 (optional)
7 TP 6310 (optional)
6N/A
5N/A
4 Eth Switch (ES)
3 Eth Switch (ES)
2 Sys Controller (SC)
1 Sys Controller (SC)
GLOBAL Logical Sys Controller (SC)
Avaya G860 Media Gateway configuration
Avaya G860 Media Gateway Setup 03-601863, Issue 1, November 2007 5
●Ethereal, version 0.10. 12 or higher, or Wireshark, version 0.99.4 or higher, with a specific
AudioCodes plug-in (provided with DVD that ships with G860 Media Gateway)
●ACSyslog093 Server (provided with DVD that ships with G860 Media Gateway)
●Boot-up server (provided with DVD that ships with G860 Media Gateway).
Pre-configuration tasks
Before beginning the configuration, you need to make sure that you have all the equipment and
it is setup to simulate the customer’s environment as much as possible, including using the
customer’s timezone.
In addition, make sure that the
●Avaya G860 Media Gateway has power. Refer to Installing and Operating the Avaya G860
Media Gateway (03-601918).
●AudioCodes EMS server software is installed on the Sun server. Refer to EMS Server
Installation, Operation, and Maintenance Manual (LTRT-94108) and EMS User’s Manual
(LTRT-91006)
●AudioCodes EMS client software is installed on the laptop. Refer to EMS Server
Installation, Operation, and Maintenance Manual (LTRT-94108) and EMS User’s Manual
(LTRT-91006)
●EMS server has the latest software version, available from AudioCodes Web site.
●SC and TP boards have the latest firmware version, available from AudioCodes Web site.
●TPM has the right feature key file. See Determining feature key file on page 6 for
procedure.
Avaya G860 Media Gateway configuration
The following sections describe how to configure the SIP and PSTN trunks and call routing for
the Avaya G860 Media Gateway. You configure the media gateway using the GUI-based
Element Management System (EMS). If configuring in a staging area, the EMS client software
is installed on the staging laptop. If configuring at the customer’s site, the EMS client software is
installed on the customer’s client computer.
The first part covers configuring the network support parameters. The second part covers
configuring the Trunk Processing Module (TPM [TP6310]) board, which controls the call
signaling for and routing between the SIP and DS3 interfaces to which it is connected.
Avaya G860 Media Gateway Setup
6Avaya G860 Media Gateway Setup 03-601863, Issue 1, November 2007
!Important:
Important: You must lock the TPM board before configuring it and unlock it once you are
done. While the board is locked, it is out of service.
Logging into the EMS
Before starting this procedure, the Element Management System (EMS) server software must
be installed and configured on the Sun server and the EMS client software must be installed on
the Windows 2003 server.
1. Double-click the desktop icon on the computer screen.
2. Type in the login, password, and the server IP address of the EMS server.
Determining feature key file
1. On the menu on the left, click Quick Setup.
Avaya G860 Media Gateway configuration
Avaya G860 Media Gateway Setup 03-601863, Issue 1, November 2007 7
2. Look in the upper right-hand corner and make sure it says 6310.
Configuring network support parameters
The main provisioning screen is the logical/geographical area where the media gateway
resides. This procedure configures the IP addresses to be used to access an NTP server and
SNMP trap receivers.
1. On the right pane under Regions List, double-click the first row entry.
Avaya G860 Media Gateway Setup
8Avaya G860 Media Gateway Setup 03-601863, Issue 1, November 2007
2. In the right pane under the MGs List, select the entry corresponding to the Avaya G860
Media Gateway to be configured.
3. Under the Media Gateway pane, click Properties.
4. Click Network Services.
5. In the NTP server field, type in the IP address for the NTP server.
Avaya G860 Media Gateway configuration
Avaya G860 Media Gateway Setup 03-601863, Issue 1, November 2007 9
6. In the EMS IP Address field, type in the IP address of the trap receiver.
Note:
Note: You can designate 2 SNMP trap receivers by filling in the NMS and OSS sections.
7. In the EMS Trap port field, type in the trap port number (default 162).
8. In the EMS Security Profile field, select EMSSecurityProfile(1).
9. Click Apply and then Close.
Locking the TPM
1. In the right pane under the MGs List, select the entry corresponding to the Avaya G860
Media Gateway to be configured.
Avaya G860 Media Gateway Setup
10 Avaya G860 Media Gateway Setup 03-601863, Issue 1, November 2007
2. 2. Click on the MG Status tab to display a replica of the front panel.
Board slots are numbered from 1 to 10 from bottom to top, as displayed on the left side of
the front panel. The Trunk Processing Modules (TPM) are in slots 9 and 10.
3. 3. Right-click on the active TPM (TP6310) shown in black and select Maintenance > Lock
4. 4. Click Yes in the confirmation window.
Configuring the TPM parameters
The Trunk Processing Module (TPM [TP6310]) must be locked before starting these steps. SeeLocking the
TPM on page 9.
1. Double-click on the locked TPM shown in black.
2. Click Properties.
Altri manuali per G860
2
Indice
Altri manuali Avaya Portale
Avaya
Avaya G150 Istruzioni operative e di manutenzione
Avaya
Avaya G450 Manager Manuale utente
Avaya
Avaya G450 Manager Manuale utente
Avaya
Avaya MCC1 Manuale utente
Avaya
Avaya G700 Guida all'installazione
Avaya
Avaya Media Gateway G250 Guida all'installazione
Avaya
Avaya G700 Manuale di istruzioni
Avaya
Avaya Media Gateway G350 Manuale utente
Avaya
Avaya RAD IPmux-14 TDMoIP Supplemento
Avaya
Avaya Media Gateway G250 Manuale utente
Avaya
Avaya G700 Guida rapida
Avaya
Avaya G450 Manager Manuale operativo e di manutenzione
Avaya
Avaya G450 Manager Guida all'installazione
Avaya
Avaya CMC1 Guida rapida
Avaya
Avaya Media Gateway G350 Manuale utente
Avaya
Avaya G700 Guida rapida
Avaya
Avaya G700 Guida rapida
Avaya
Avaya G450 Manager Manuale di istruzioni
Avaya
Avaya Media Gateway G350 Manuale utente
Avaya
Avaya G860 Schema elettrico
Manuali Portale popolari di altre marche
LST
LST M500RFE-AS Manuale utente
Kinnex
Kinnex Media Gateway Manuale utente
2N Telekomunikace
2N Telekomunikace 2N StarGate Manuale utente
Mitsubishi Heavy Industries
Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuale utente
ZyXEL Communications
ZyXEL Communications ZYWALL2 ET 2WE Manuale utente
Telsey
Telsey CPVA 500 - SIP Manuale utente
