Aveo Systems VISCA Pan Manuale utente

VISCA Pan, Tilt, Zoom Cameras

PTZ Camera

Pan, Tilt, Zoom (PTZ) cameras can be controlled by Mira Connect™, Aveo

Systems’ smart control appliance. Mira Connect uses Sony’s VISCA (Video

System Control Architecture) camera protocol to control pan, lt, and zoom,

for VISCA-compable cameras.

In addion to camera pan, lt, and zoom control, Mira Portal supports saving

camera presets, making it easy to restore presets with Mira Connect to

re-posion the camera to predened locaons.

To integrate a PTZ Camera with Mira Connect, add a ‘Universal VISCA

Camera’ to the room in Mira Portal (hps://mira.aveosystems.com)

and enter the IP address of the camera and the TCP port number. If

you don’t have an actual PTZ camera while conguring Mira

Connect, you can choose to simulate the PTZ Camera by checking

the ‘Simulate equipment’ box.

If the camera is to be controlled directly over its Ethernet

interface, the port number to use will be described in the camera’s

documentaon. If the camera will be controlled over RS-232 using a

Global Caché IP2SL interface, the port number should be set to 4999

(the default).

Next, navigate to the Camera Conguraon tab and enter the

camera’s ID (typically 1) and enter a name for the camera and press

‘add equipment’.

If you have more than one camera daisy-chained over RS-232, click

ADD DAISY-CHAINED RS-232 CAMERA to enter addional cameras.

The camera names will be visible on Mira Connect on the Cameras

menu.

Once the cameras have been added, Mira Connect will connect to

the devices and show the status of the connecon. Mira Portal will

show the equipment status as a green circle with a check mark if the

equipment was detected at the specied IP address and network

port and is controllable by Mira Connect.

If the camera cannot be connected to by Mira Connect, a warning icon ! will appear on the equipment list. If this

happens, rst check the RS-232 baud rate used by the Global Caché IP2SL (most VISCA cameras operate at 9600

bps while the Global Caché IP2SL defaults to 19,200), and then edit the camera sengs and conrm the IP address,

port number, and camera IDs used for the cameras.

On each camera, ensure the camera ID is set to the desired value (or set automacally), the VISCA protocol is

enabled, and the RS-232 baud rate sengs match the Global Caché IP2SL RS-232 sengs. Adjusng sengs on

the camera may requires access to the camera’s infra-red (IR) controller.

Step

Mira Connect Integraon

SYSTEMS

CAMERA PRESETS

RESET TO DEFAULT

CAMERA CONFIGURATIONCONNECTION

192.168.100.192

5678

Add Equipment

Equipment Type*

Simulate equipment

Universal VISCA Camera

Didn’t ﬁnd your equipment? Request it!

IP Address or Hostname *

Port Number * Default port 4999 is for use with Global Caché iTach IP2SL

ADD EQUIPMENTCANCEL

Update Equipment

UPDATE EQUIPMENTCANCEL

CONNECTION CAMERA CONFIGURATION

Equipment Type*

Camera ID * Camera Name *

Simulate equipment

Universal VISCA Camera

1 ClearOne Unite 200

Didn’t ﬁnd your equipment? Request it!

Camera ID * Camera Name *

2 Another Camera

ADD DAISY-CHAINED RS-232 CAMERA

REMOVE

Add any VISCA cameras that are daisy-chained via RS-232.

CAMERA PRESETS

192.168.100.192

Universal VISCA Camera

Equipment

ADD

Firmware: 00 01 04 02 01 15 02

192.168.100.192

Universal VISCA Camera

Equipment

ADD

Edit equipment to complete additional configuration

Aveo Systems, Inc. • 1791 West Oak Parkway • Suite 8 • Mariea, GA 30062 • Phone: +1.678.653.7090 Fax: +1.844.fax.aveo

• Email: info@aveosystems.com • www.aveosystems.com

SYSTEMS

Successful connecon to the camera.

Camera can not successfully communicaon with

Mira Connect.

Enter the camera ID and camera name. VISCA daisy-chained

cameras are supported.

Enter the IP address and port number.

Mira Connect Integraon with PTZ Cameras

To add Camera Presets, press the Camera icon,

CAMERA

, on Mira Connect and select a camera from the camera pull

down box on Mira Connect. Next, manually posion the camera using Mira Connect (or use the remote control

capabilies from Mira Portal) to the desired locaon and zoom level.

Next, edit the equipment in Mira Portal and navigate to the Camera Presets tab. Select the desired camera from

the pull down list, and click ADD PRESET. Select an icon, and enter a preset name and oponal descripon.

Once the camera is in the desired locaon, press SAVE PRESET to save that camera posion. Repeat the process for

saving mulple camera presets. When nished saving presets, click Update Equipment to store the preset

informaon and update the user interface on Mira Connect. Presets will appear in Mira Connect as shown on the

right of the following gure.

Note that presets won’t appear on Mira Connect unl Update Equipment has been selected on Mira Portal.

Camera Posioning Speed Control

VISCA cameras from various manufacturers have dierent sensivies to VISCA camera move commands - some move

quickly and some move slowly. To account for these dierences, Mira Portal supports seng camera movement speeds

for pan, lt, and zoom both when the movement buon is tapped and when it is held. To congure these sengs,

navigate to the Camera Conguraon tab in Mira Portal and increase or decrease the moon speed as shown in the

following gure. Pan speed can be adjusted from 1 to 24 (fastest), lt speed from 1 to 20 (fastest), and zoom speed from

1 to 7 (fastest).

Step

Pan/Tilt

Select camera:

Zoom

WIDE VIEW

Full Room View

Camera presets:

Smaller Meeting

Front of Room

One on One

TABLE END CLOSE UP VIEW

PRESENTER

FRONT OF ROOM

Update Equipment

CONNECTION CAMERA CONFIGURATION CAMERA PRESETS

Equipment Type*

Simulate equipment

Universal VISCA Camera

Camera

These preset items will appear on Mira Connect.

Icon Label

WIDE VIEW

ADD PRESET

SAVE POSITIONREMOVE

View of the Room

View of the Room Front of Room

Front of Room

Camera Presets Preview

Camera presets:

After adding a preset, save the current camera position

to that preset with the “Save Position” button.

Descripon (Oponal)

Label

PRESENTER

SAVE POSITIONREMOVE

Front of Room

Descripon (Oponal)

UPDATE EQUIPMENTCANCEL

Didn’t ﬁnd your equipment? Request it!

Smaller Meeng One on One

TABLE END CLOSE UP VIEW

Questions about Universal VISCA Camera?

See the integration guide.

Update Equipment

CONNECTION CAMERA CONFIGURATION CAMERA PRESETS

Equipment Type*

Simulate equipment

Universal VISCA Camera

ADD DAISY-CHAINED RS-232 CAMERA

Camera 11 8 8

Add any VISCA cameras that are daisy-chained via RS-232

Invert Pan Controls

Camera ID * Camera Name * Pan Speed *

Pan Speed (Slow) *

Tilt Speed (Slow) *

Zoom Speed (Slow) *

Tilt Speed *

Zoom Speed *

UPDATE EQUIPMENTCANCEL

Didn’t ﬁnd your equipment? Request it!

Mira Connect Integraon with PTZ Cameras

The rst row of speed controls aect when the pan, lt, or zoom buon is pressed and held. Default values are Pan

Speed: 8, Tilt Speed: 8, and Zoom Speed: 3. The second row of speed controls aect when the pan, lt, or zoom buon is

tapped. Default speed values are Pan Speed (Slow): 3, Tilt Speed (Slow): 3, and Zoom Speed (Slow): 1.

To increase the speed of camera movement, increase the speed value. To decrease the speed of movement - mostly used

when tapping the buon once moves the camera too much - lower the speed number.

Invert Pan Controls

If you’d like to reverse le and right camera movements when using Mira Connect (highlighted

in the gure on the right) when the camera navigaon buons are pressed on Mira Connect,

enable the invert pan control opon for each camera in your system.

Connecon Interface

Network connecon using default TCP port 4999 with a Global Caché IP2SL interface, or a dierent user specied port for

direct Ethernet control for cameras that support Ethernet control. See our integraon guide for conguring the IP2SL.

When using the Global Caché IP2SL interface for serial control, use Global Caché’s iHelp program to discover the IP2SL’s

IP address, then browse into the device to set the desired stac IP address. The Global Caché IP2SL with PoE (part

number 151.0010.001) is available as an accessory from Aveo Systems.

Ensure the baud rate on the Global Caché IP2SL matches the baud rate congured on the camera. Default RS-232 sengs

for most PTZ Camera are 9,600 baud, 8 data bits, no parity, 1 stop bit, no ow control.

Use a straight-through RS-232 cable that you provide as shown in the following gure to connect the Global Caché IP2SL

to the RS-232 IN connector on the camera. An example cable that is known to work is available here.

Global Cache IP2SL

Pin 1Pin 5

Pin 9 Pin 6

Pin Signal

2 RX

3 TX

5 Ground

DB9 Female

DB9 Male

DB9 Female

Pin Signal

3 TX

4 Ground

5 RX

DIN Male

Straight-Through RS-232 Control Cable DB9F - VISCA 8-pin DIN Male

RS-232 Connector

is DB9 Male

1 2

3 4 5

6 7 8

RS-232 connector

is 8-pin DIN Female

Equipment to be Controlled

345

IN OUT

VISCA

RS-232

Mulple cameras are supported on a single RS-232 interface by daisy-chaining the RS-232 OUT port of one camera to the

RS-232 IN port on the next camera. All cameras must have unique IDs ranging from 1 to 7. Typically the camera ID’s are

created automacally by the cameras as they communicate over RS-232. To connect mulple cameras using the VISCA in

and out connecons, create or purchase a cable with the following pin-out.

Tested Systems

ClearOne Unite 150 and 200 cameras, Sony EVI-D70, HuddleCam HC10X, HuddleCam HC3X.

Pan/Tilt

Pin Signal

3 TX

4 Ground

5 RX

DIN Male

DB9 Male

DB9 Female

Pin Signal

3 TX

4 Ground

5 RX

DIN Male

RS-232 Control Cable VISCA 8-pin DIN Male - VISCA 8-pin DIN Male

1 2

3 4 5

6 7 8

1 2

3 4 5

6 7 8

RS-232 connector

is 8-pin DIN Female

RS-232 connector

is 8-pin DIN Female

VISCA CameraVISCA Camera

345

INOUT

Mira Connect Administrators Guide

See the Mira Connect Administrators Guide for addional informaon about using Mira Portal to set up Mira Connect.

Informaon about integrang specic cameras is summarized below.

Zoom Rooms Integraon

If integrang one or more VISCA cameras with Zoom Rooms video conferencing systems, associate the VISCA camera(s)

with the Zoom Rooms using the Zoom Rooms CAMERA & AUDIO tab as shown in the following gure.

See the Zoom Room Integraon guide for addional informaon about seng up a Zoom Rooms system with Mira

Connect.

Update Equipment

UPDATE EQUIPMENTCANCEL

CONNECTION CAMERAS & AUDIO VIDEO INPUTS

Equipment Type*

Simulate equipment

Zoom Rooms

USB Camera

Camera Names and Control

A camera can be given a name that is more meaningful to a user, such as “Room Overview” or“Document Camera”. Selecting a VISCA camera

interface from the list will provide pan, tilt, and zoom controls.

OPTIONS

Build-in Input (Line In) Volume

Microphone

Built-in Output (Internal Speakers)

Unite 150 Front of Room Front of Room

Camera Name VISCA Camera Control

Speaker

Volume

Specic Camera Informaon

ClearOne Unite 200

The ClearOne Unite 200, when controlled over its Ethernet interface, uses port 5678 by

default. This port can be changed from the camera’s web interface. The default IP address

of the ClearOne Unite 200 is 192.168.100.88 with username and password “admin” and

“admin”, respecvely.

When controlled over its Ethernet interface, the camera properly supports all camera posioning, however it does not

support power on and o commands. Powering o the room using Mira Connect will not put the camera into standby

mode as the power state will remain unchanged.

If the camera is powered o via an IR remote, it cannot be powered back on via Ethernet control. If the Unite 200

camera is powered on via its IR remote, the camera’s Ethernet interface is reset upon power up, causing Mira Connect

to re-establish network communicaon. Upon power up, camera control features are briey unavailable while Mira

Connect automacally re-establishes the network connecon.

When controlled over its RS-232 interface, the ClearOne Unite 200 camera correctly supports power on and o

commands and supports going into and out of standby mode.

DS-11001-021

Version 2019_10_24

Specicaons subject to change without noce. Aveo Systems and the Aveo logo are registered trademarks.

All other trademarks are the property of their respecve owners.

For more informaon please contact our Sales Department at sales@aveosystems.com.

About Aveo Systems

Aveo Systems is a leading provider of intuive and easy-to-use soluons for audio, video, and

collaboraon, improving how systems are used and managed by customers world-wide.

SYSTEMS

Mira Connect Integraon with PTZ Cameras

Questo manuale è adatto per i seguenti modelli

Manuali Telecamera di sicurezza popolari di altre marche

Okina USA

Okina USA SIR36-870VF650LP Manuale utente

Divio

Divio NDR155PA Manuale utente

Canon

Canon VB-C500D Manuale utente

Easy Access

Easy Access EasyGuard Manuale utente

Vivotek

Vivotek FD9389-EHV-v2 Manuale utente

TUYA

TUYA COSMO W2 Manuale utente

Eusso

Eusso UNC7500-IR Guida all'installazione

urmet domus

urmet domus 1096/204 Manuale utente

VC VC20 series Manuale utente

Axis

Axis Q1614 Manuale utente

ieGeek

ieGeek DD201 Manuale utente

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuale utente

Vicon

Vicon V662-D-1 Istruzioni operative

Grundig

Grundig GCH-K0274P Manuale utente

Lorex

Lorex VANTAGE LBC7032 Manuale utente

4xem

4xem WPT Manuale utente

Samsung

Samsung SCV-3082 Manuale utente

Vitek

Vitek VTC-C544 Manuale utente