AVOCOR AVE-7510 Manuale utente
AVE Series
Quick Start Guide
AVE-6510, AVE-7510, AVE-8610
v.08_08_2018 2
E Series Quick Start Guide Table of Contents
3. Contents of Packaging
4. The Display at a Glance
7. Display Input Sources
9. The Remote Control
10. Switching the display on and off
Source Selection
Connecting to the Display
11. Connecting to an external PC using a HDMI connection
12. Connecting to an external PC using a DisplayPort connection
13. Enabling the Touch System
14. Installing an OPS Module
15. Warranty Support
v.08_08_2018 3
Contents of Packaging
1. Accessory Carton
•Quick Start Guide
•Remote Control & Batteries
•2x Touch Stylus – 1x3mm & 1x6mm
•Eraser
•Power Cables - UK Cable 2m & European Cable 2m
•2x 3m HDMI Cable
•2x 3m USB-A – USB-A Cable
•Cleaning Cloth
•Pen Holder
Please visit www.avocor.com to download the full E-Series user manual
and the Pen Aware Touch Drivers.
v.08_08_2018 4
The Display at a Glance
Front View
Rear View
v.08_08_2018 5
v.08_08_2018 6
Front Buttons
Button
Operation
Function
Power Short Press
Power on/off Indicator
LED status:
● Solid Red : Sleep mode
● Solid Green : Working state
● Blinking Red and Green : Standby mode
Menu Short press Open the Settings menu
Source
Short press
Open the Source menu
Mute Short press Mutes the audio
VOL -
Short press
Decrease the audio volume in steps
Long press - more than 1 sec Decrease the sound volume continuously
VOL+ Short press Increase the audio volume in steps
Long press - more than 1 sec Increase the sound volume continuously
v.08_08_2018 7
E-Series Display Inputs
Front Ports
v.08_08_2018 8
Rear Ports
v.08_08_2018 9
Remote Control
Label
Description
Turns the display on and off.
Select the OPS PC source.
Blanks the display. Press again to restore.
Freezes the display. Press again to restore.
Navigates through menus and settings.
Selects highlighted menu choice
When the menu system is already open, pressing
this button will close the on screen menu.
Opens the display menu system.
Mutes the audio. Pressing Mute again restores the
audio
Decreases the Volume by pressing the - key
Increases the Volume by pressing the + key
Opens the Source Menu.
Selects DisplayPort
Selects the HDMI Sources
Selects each aspect ratio, in sequence: Full
Screen, Auto, Pillar Box
v.08_08_2018 10
Switching the Avocor display on and off
Switching on
1. Plug the end of the supplied power cord into side of the display
2. Connect the other end to the power source.
3. Turn on the main power switch at the side of the display. The power LED indicator lights
Red to indicate that the display is in “standby” mode.
4. Press the Power button and the power LED indicator on the left-hand side of the display
will then light up in green, which tells you that the screen is switched on.
5. After a brief warm-up period, the display will display an image
Switching off
1. Switch the display off by pressing the Power button on the display.
2. The display will then cycle and shut down.
Selecting the Source
You can access several sources on the Avocor E-Series display including, HDMI,
DisplayPort, & OPS.
The Source button is located on the Connect & Control Bar or on the Remote Control.
Once the menu has been selected, you will see the option to select the source you
require.
HDMI 1, HDMI 2, HDMI 3, DisplayPort, OPS, & Front HDMI
If there is no active signal from the chosen source, the screen will display the following
message: “No Signal”.
Connecting the Display
Proceed as follows to connect the display to your video sources, external controller.
When connecting your equipment:
1. Turn off all equipment before making any connections.
2. Use the correct signal cables for each source.
3. For best performance and to minimise cable clutter, use high-quality cables that are
only as long as necessary to connect two devices. (Don't use a cable longer than 5
metres).
4. Ensure that the cables are securely connected.
Questo manuale è adatto per i seguenti modelli
3
Indice
Altri manuali AVOCOR Pannello touch
