AXC HALO Manuale utente
HALO –FVP Frame - Assembly Manual V1.1
Designs, Images and Content Copyright © Aeroxcraft Ltd. 2012 –2016
Page 1
Assembly Manual
Micro FVP Frame
HALO –FVP Frame - Assembly Manual V1.1
Designs, Images and Content Copyright © Aeroxcraft Ltd. 2012 –2016
Page 2
Notes
It is the owner’s responsibility to ensure this model is assembled and fitted out correctly and
safely. Ensure that your model is capable of safely and reliably lifting the payload you are
asking it to. This model is dangerous if used in an incorrect manner. Ensure you seek
assistance from an experienced flyer if you are unsure. Do not fly near people, property or
highways. Do not fly over people, property or highways. There may be laws and regulations
governing the use of this model in your area, seek advice from your authorities if you are
unsure.
Planning your build and installation is key to building a safe and reliable multi rotor. Make sure
all wiring is of the correct gauge, properly connected, neat and protected from wear/tear and
radio/electrical interference. Make sure all the components you use are suitable for the size
and weight of your multi rotor.
Do not over tighten screws. Use of thread-lock is recommended.
Check this product for damaged hardware, loose joints, missing parts or sharp edges before
and after assembly and frequently during use. Do not use unless all components are correctly
fitted and adjusted. Do not use if any parts are missing, damaged or broken.
Assembly is required. Take care when unpacking and assembling; contains small parts and
sharp edges.
If you require any replacement parts they are all available from Aeroxcraft.
http://www.aeroxcraft.com/
Contact details
Email
Website
www.aeroxcraft.com
HALO –FVP Frame - Assembly Manual V1.1
Designs, Images and Content Copyright © Aeroxcraft Ltd. 2012 –2016
Page 3
Document Contents
Page No
Notes.............................................................................................2
Contact details ..............................................................................2
Document Contents.......................................................................3
Package Contents.........................................................................4
Introduction ...................................................................................6
Step 1 - Assemble Flight Components..........................................7
Step 2 - Assemble Upper Structure...............................................8
Step 3 - Attach Upper Structure ....................................................9
Step 4 - Attach Camera...............................................................10
Step 5 - Attach Battery Straps.....................................................11
Step 6 - Attach Props & Fly!........................................................12
Flight Controller Setup.................................................................13
Useful Links.................................................................................13
HALO –FVP Frame - Assembly Manual V1.1
Designs, Images and Content Copyright © Aeroxcraft Ltd. 2012 –2016
Page 4
Package Contents
Carbon and G10 parts
Qty
Item
Part No
4
Carbon Hoop
1
Main Plate
2
Camera Supports
2
Antenna Protector
Aluminium Parts
Qty
Item
Part No
4
Spacer Blocks
4
Hoop Supports
1
Camera Mount
HALO –FVP Frame - Assembly Manual V1.1
Designs, Images and Content Copyright © Aeroxcraft Ltd. 2012 –2016
Page 5
Hardware Bag
Qty
Item
24
M2 x 4 Socket Screws
16
M2 x 3 Socket Screws (For mounting Motors)
8
M2 x 5 CSK Pozi Screws
4
M2.5 x 20 CSK Pozi Screws
4
M2.5 Nuts
8
1.6mm Spacers
8
3.2mm Spacers
8
4.8mm Spacers
2
Washers
1
200mm x 10mm Velcro Strap
1
100mm x Self Adhesive Velcro (Hook)
1
100mm x Self Adhesive Velcro (Loop)
6
Cable Ties
HALO –FVP Frame - Assembly Manual V1.1
Designs, Images and Content Copyright © Aeroxcraft Ltd. 2012 –2016
Page 6
Introduction
This is a basic assembly manual for the construction of the AXC Halo. It does
not explain how to connect and setup the Flight controller, ESC, Motors, VTX,
RX etc.
We are working on more detailed assembly instruction that we will release
soon.
We recommend the following components for the AXC Halo:
Flight Controller: (1x) FuriousFPV PIKO BLX (20x20mm mounting
holes)
ESC: (2x) FuriousFPV SILKY 2in1 ESC BLHELI_S (20x20mm
mounting holes)
Props: (4x) FuriousFPV 1935
Motor: (4x) DYS BE1104 - 6500KV / RotorX RX1105B - 6500kv
Battery: (1x) 400-500mah 3S Lipo
RX: (1x) Furious Mini RX for Frsky
Camera/VTX: (1x) FX798T 5.8G 25mW 40CH Mini FPV Transmitter
Camera Combo
USB: For connecting the PIKO flight controller to your computer a
90deg USB lead will be very useful.
HALO –FVP Frame - Assembly Manual V1.1
Designs, Images and Content Copyright © Aeroxcraft Ltd. 2012 –2016
Page 7
Step 1 - Assemble Flight Components
Assemble and setup all the flight components at this stage. Cut wires to
length and solder in place. Make sure all the wiring is clear of the propellers.
Being neat and tidy at this stage will help ensure your success!
Mount the ESC, Flight Controller, etc
(1x) Main Plate
(4x) M2.5 x 20mm CSK
(4x) M2.5 Nuts
Plastic spacers as required
Make sure the screws and nuts do not cause any electrical short outs.
The arrow in the Main Plate is to point forwards. It helps to avoid confusion
later!
Mount the Motors
(16x) M2 x 3mm Socket screws
Make sure the screws do not damage the internal wire inside the
motors.
Do not overtighten the screws as it will damage the motor screw
threads.
Thread-lock will stop screws becoming loose and falling out when there
are vibrations. Excessive vibrations can occur if you damage a
propeller.
HALO –FVP Frame - Assembly Manual V1.1
Designs, Images and Content Copyright © Aeroxcraft Ltd. 2012 –2016
Page 8
Step 2 - Assemble the Upper Structure
(4x) Carbon Hoops
(4x) Spacer Blocks
(4x) Hoop Supports
(2x) Camera Supports
(12x) M2 x 4 Socket Cap Screws
(8x) M2 x 5mm CSK (Countersunk) Pozi Screws
Assemble the parts as per the diagram below.
Use M2 x 5mm CSK (Countersunk) Pozi Screws in the upper holes. This
allows the props to clear the screws if the props deform upwards at full
throttle.
HALO –FVP Frame - Assembly Manual V1.1
Designs, Images and Content Copyright © Aeroxcraft Ltd. 2012 –2016
Page 9
Step 3 –Attach Upper Structure
(8x) M2 x 4mm Socket Cap Screws
Attach the upper structure to the Main Plate with the 8 screws.
HALO –FVP Frame - Assembly Manual V1.1
Designs, Images and Content Copyright © Aeroxcraft Ltd. 2012 –2016
Page 10
Step 4 –Attach Camera
The camera attaches to the rear of the aluminium camera mount with the pre-
attached self-adhesive foam tape.
Make sure that no electrical parts of the camera can touch the aluminium to
avoid electrical short out. This includes sharp solder points that can pierce the
self-adhesive foam tape. Carefully file down any sharp solder points that may
be affected
Check your camera is supplied with the correct voltage from your power
distribution.
Attach the aluminium camera mount and antenna protectors to the camera
supports.
(1x) Aluminium Camera Mount
(4x) M2 x 4mm Socket Cap Screws
(2x) Antenna protectors
The angle of the camera is adjustable. Slacken the screws, change the
camera angle and retighten the screws.
Indice
Altri manuali AXC Quadricottero
