Axesstel AXW-D1900 Manuale utente
1xEV-DO Wireless Broadband Modem AXW-D800/D1900
Axesstel 1
Axesstel 1xEV-DO Wireless Modem
User Manual
Rev: 0.01.01
Axesstel, Inc.
1xEV-DO Wireless Broadband Modem AXW-D800/D1900
Axesstel 2
Table of Contents
Introduction ____________________________________________________ 3
Features _______________________________________________________ 3
Safety Precaution________________________________________________ 4
Contents _______________________________________________________ 5
Desktop Installation______________________________________________ 6
Wall Mount Installation ___________________________________________ 6
Getting to know the modem _______________________________________ 7
Connecting Axesstel EVDO Wireless Modem_________________________ 8
Configuring Your Wireless Modem _________________________________ 9
USB Driver Installation __________________________________________ 14
TCP/IP Settings ________________________________________________ 16
Troubleshooting________________________________________________ 18
SPECIFICATIONS_______________________________________________ 19
1xEV-DO Wireless Broadband Modem AXW-D800/D1900
Axesstel 3
Introduction
Axesstel's 1xEv-DO Broadband Wireless Modem allows users to "get
connected" to high speed data services with unprecedented ease. Powered by
QUALCOMM's MSM6500 processor, these modems provide high speed data
service through USB and Ethernet interfaces at rates of up to 2.4Mbps
download and 153.6 Kbps upload. With RJ-45 Ethernet connection, the users
can enjoy true plug and play connection without driver installation.
Features
zCDMA 1xEV-DO data service with speed up to 2.4Mbps download and
153.6Kbps upload
zBackward compatible to CDMA2000 1xRTT Data service (153.6 Kbps
max)
zReceive diversity (2 antennas) for enhanced RF performance
z4 LED indicators (Power, Signal Strength, Connection, and Ethernet)
zRJ-45 Ethernet and High Speed USB 1.1 data port
zWeb based Admin tool
zDesktop or Wall-Mountable
zOptional Range-extending Patch Antenna
1xEV-DO Wireless Broadband Modem AXW-D800/D1900
Axesstel 4
Safety Precaution
1. Avoid placing the unit in a dusty location, or near a source of gas or fire.
2. Do not shake, hit or drop the unit.
3. To clean the unit, use only a soft, dry cloth. The chemicals in alcohol,
benzine or acetone can damage the surface of the unit.
4. Do not twist or pull the cord out of the unit.
5. Do not disassemble the phone.
6. DO NOT use the power adapter if the power cord is damaged or the unit has
been dropped or damaged in any way.
7. Only use the power adaptor provided by Axesstel. Do not use the
AXESSTEL adapter for any other purpose.
8. Use only the antenna provided with the unit. Do not use the antenna for
any other purpose.
9. Do not use the unit near water, for example, near a bathtub, sink, wet
basement, or swimming pool.
NOTE: The input voltage and the shape of the plug on this phone may vary
from country to country.
1xEV-DO Wireless Broadband Modem AXW-D800/D1900
Axesstel 5
Contents
After opening the package, check to make sure that you have all the parts
shown below. If any piece is missing or broken, please call your agent or
customer service. Items marked optional may be available only on select
models.
1. Main Unit 4. User’s Manual
2. Antenna (2) 5. USB Cable (Optional)
3. AC/DC Adapter and AC Cord 6. Ethernet Cable (Optional)
1xEV-DO Wireless Broadband Modem AXW-D800/D1900
Axesstel 6
Desktop Installation
The 1xEV-DO Modem operates by receiving electricity from an electrical outlet.
1 Connect the antennas on the connectors of each side of the unit..
2 Connect the Modem to computer using RJ-45 Ethernet Cable (CAT 5) or USB
cable.
3 Move the connection selector switch to USB or Ethernet.
4 Connect the power adaptor to the DC 9V socket of the modem.
4 Plug the AC adaptor into an appropriate electrical wall outlet.
5 Turn on the power switch located next to the DC 9V socket.
Wall Mount Installation
1 Mark two mounting holes on the wall using the hole locator on the last page of
the manual.
2 Drill two holes at the marked locations.
3 Tighten the screws until the head is about 5mm from the wall.
4 Hang the modem on the screw using the two holes in the back.
5 Push the modem down until the unit is firmly locked into place.
1xEV-DO Wireless Broadband Modem AXW-D800/D1900
Axesstel 7
Getting to know the modem
LED indications
LED Color Meaning
Green Power is on
Power Off Power is off
Green Excellent Signal
Orange Good Signal
Red Poor Signal
Signal
Off No Signal or Service is present
Green Modem is connected to the CDMA network
Connect Off Modem is not connected
Green PC connected to the Ethernet
Blinking Indicates data activity
Ethernet
Off No PC is connected to the Ethernet
Power ON/OFF Switch
There’s power switch on the front side of the modem.
Turn on the modem by moving switch to ON position. Turn off the modem by
moving switch to OFF position.
NOTE: When you turn on the modem, it automatically searches for service
signal. When it successfully acquires service signal, the signal LED turns to
green, orange or red.
Connection Type Switch
Connection Type Switch is located between Ethernet port and USB port. Set
this switch to Ethernet or USB depending on type of connection you are using.
1xEV-DO Wireless Broadband Modem AXW-D800/D1900
Axesstel 8
Connecting Axesstel EVDO Wireless Modem
Before you start
1. Make sure that your account is active. Please contact your ISP for
account setup and activation information.
2. Configure your PC to obtain TCP/IP settings automatically from DHCP
server feature of Wireless Modem. Refer to “TCP/IP Settings” for more
information on how to set up TCP/IP settings on your PC.
3. In order to connect multiple PCs to Wireless Modem and share internet
connection, you will need a Broadband Router, Ethernet Switch, or Hub.
Please refer to instructions on your Broadband Router for information on
connecting multiple PCs.
Connection using Ethernet port
1. Connect coaxial cable to Ethernet port of Wireless Modem.
2. Connect other end of coaxial cable to RJ-45 port of your PC’s Ethernet
network adapter or a network device, such as router or hub.
3. Connect the included Power Adapter to Power connector of Wireless
Modem. Connect the other end of Power Adapter to an electrical outlet.
4. Power on Wireless Modem.
5. It will take few seconds for Wireless Modem to establish a connection.
1xEV-DO Wireless Broadband Modem AXW-D800/D1900
Axesstel 9
Connection using USB port
1. Power off your PC.
2. Connect the included USB Cable to USB port on your PC.
3. Connect other end of USB Cable to USB port on Wireless Modem.
4. Connect the included Power Adapter to Power connector of Wireless
Modem. Connect the other end of Power Adapter to an electrical outlet.
5. Power on Wireless Modem.
6. Power on your PC. During the boot up process, your PC will recognize
Wireless Modem and ask to install Wireless Modem drivers. You need to
install Wireless Modem USB driver that was supplied with Wireless
Modem. Refer to “USB Driver Installation” for more information.
Configuring Your Wireless Modem
Wireless Modem provides an embedded Web-based Management Utility.
Configure your Wireless Modem by using your Web Browser.
Log In
•Open Web browser and enter IP address of Wireless Modem. Default IP
address of Wireless Modem is 192.168.0.1
•When prompt for User name and password, enter admin/admin.
•Click on appropriate tab to access System, Network, Security, or Status
settings.
1xEV-DO Wireless Broadband Modem AXW-D800/D1900
Axesstel 10
System Window
Host Name: Name of the Wireless Modem. You may change this
name according to your network need.
Change Password: To change the password of your account, enter your old
password and new password.
System Upgrade: To download new firmware.
Restore Default: Restore all settings to factory default settings.
Reboot System: Restart Wireless Modem.
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Axesstel Modem
