Axxess AX-DSP-X Manuale utente
AXDSP-X
INSTALLATION INSTRUCTIONS
AxxessInterfaces.com © COPYRIGHT 2020 METRA ELECTRONICS CORPORATION REV. 1/30/2020 INSTAXDSP-X
Google Play Store Apple App Store
iOS 12.1 or higher
INTERFACE FEATURES
INTERFACE COMPONENTS
TOOLS & INSTALLATION ACCESSORIES REQUIRED
• Crimping tool and connectors, or solder gun,
solder, and heat shrink • Tape • Wire cutter
• Zip ties • Multimeter
TABLE OF CONTENTS
Preface ....................................................................2
Installation Options ...............................................2
Installation .............................................................3
Connections ........................................................ 4-7
AXDSP-X app .....................................................8-17
Pinout ....................................................................18
Specifications ....................................................... 19
Axxess 10-Channel Digital Signal Processor
• 31 Band graphic EQ
• 6 Inputs, 10 individually assignable outputs
• Independent equalization on each of the 10 outputs
• Independent high pass, low pass, and bandpass filters
• Each channel can be delayed independently up to 10ms
• Chime control for GM/Chrysler vehicles
• Clipping detection and limiting circuits
• Bass knob included
• Retains OE voice prompts (SYNC® and OnStar®)
• Retains factory chimes including parking sensor and cross path
detection alerts
•
Settings adjusted via Bluetooth® in a smart device application (tablet
or mobile phone), compatible with both Android and Apple devices
• Read, write, and store configurations for future recall
• Password protect feature available in the mobile app
• Micro-B USB updatable
• AXDSP-X interface
• AXDSP-X harness (16-pin & 20-pin)
2
Aftermarket radio system:
The AXDSP-X can be used with an aftermarket radio to improve the overall listening
experience for car audio enthusiasts. Installers will connect the RCA inputs from the AXDSP-X
to the outputs from the aftermarket radio; Front, Rear, Sub (sub is optional).
(refer to page 4)
Adding a subwoofer to an existing radio:
This feature offers the Installer the ability to add an aftermarket subwoofer to an existing
radio. (refer to page 5)
Full range system to an existing radio:
This option allows the Installer to wire the AXDSP-X directly to the speaker outputs from an
existing radio for a full range audio signal (high-level).
(refer to page 6)
PREFACE INSTALLATION OPTIONS
In the following section, Installation Options, choose the installation type, then either click on
the hyperlink, or reference the page number.
The AXDSP-X provides a 12v 1-amp output to turn on an aftermarket amplifier. If installing
multiple amplifiers, an SPDT automotive relay will be required if the current exceeds that
amount. Use Metra part number E-123 (sold separately) for best results.
The AXDSP-X can also grow as your stereo system grows. Start off by adding a subwoofer, then
add on from there. Simply reference the Installation Options page to change the AXDSP-X to the
new system. All 10 channels of the AXDSP-X can be assigned however needed for the installation
at hand. If 10 channels of a subwoofer signal is needed, the AXDSP-X can do it.
3
REV. 1/30/2020 INSTAXDSP-X
I N S TAL L AT IO N
1. Complete all necessary connections to the radio and vehicle, but leave the amp turn-on
wire disconnected.
2. Plug the 20-pin AXDSP-X harness into the AXDSP-X.
3. Plug the 16-pin AXDSP-X harness into the AXDSP-X.
4. Download and install the AXDSP-X app from the Google Play Store or Apple App Store.
5. Using the app, select the vehicle.
6. Connect the amp turn-on wire from the AXDSP-X.
7.
Adjust the DSP settings in the app as desired. Refer to the instructions starting on (page 7)
for an explanation of each tab in the app. (refer to page 7)
4
FrontRearSub
Bass Knob
(included)
RCA Jacks
(sold separately)
Aftermarket Radio
AXDSP-X
(included)
Do not use amp turn-on
from aftermarket radio!
Any remaining wires
tape off and disregard
Blue/White - Amp Turn-On Wire
Assignable Outputs Labeled CH 6-10
INPUT 5
INPUT 6
INPUT 5
Optional
An SPDT relay, Metra part number
E-123, must be used if more than
one amplifier will be installed
Black - Chassis Ground
Yellow - Battery Power
Red - Accessory Power
Orange - Control Wire
AFTERMARKET RADIO SYSTEM
5
REV. 1/30/2020 INSTAXDSP-X
ADDING A SUBWOOFER TO AN EXISTING RADIO
RCA Jacks
(sold separately)
Blue/White - Amp Turn-On Wire
Bass Knob (included)
Factory Radio
These outputs can be used for
additional sub amps, or for adding
onto the system at a later date
INPUT 5
Orange - Control Wire
INPUT 6
AXDSP-X (included)
Wire information on page 17
(RCA Jacks shown cut off)
6
FULL RANGE SYSTEM TO AN EXISTING RADIO
Blue/White - Amp Turn-On Wire
Bass Knob (included)
Factory Radio
INPUT 5
Orange - Control Wire
INPUT 6
An SPDT relay, Metra part number
E-123, must be used if more than
one amplifier will be installed
RCA Jacks
(sold separately)
Assignable Inputs Labeled CH 6-10
AXDSP-X (included)
Wire information on page 17
(RCA Jacks shown cut off)
7
REV. 1/30/2020 INSTAXDSP-X
AXDSP-X APP
Setup Instructions
• General information tab for installing the AXDSP-X.
Continued on the next page
8
AXDSP-X APP (CONT.)
Bluetooth Connection
• Scan - Press this button to start the Bluetooth pairing process, then
select the AXDSP-X from the mobile device. The AXDSP-X must be
powered during this process. Confirmation that you are connected
will show in the top left corner of the app.
• Disconnect - Disconnects the AXDSP-X from the app.
Continued on the next page
9
REV. 1/30/2020 INSTAXDSP-X
Continued on the next page
AXDSP-X APP (CONT.)
Configuration
• Identify - Click this button to confirm that the AXDSP-X is connected
properly. If so, a chime will be heard from the front left speaker.
• Reset to Defaults - Resets the AXDSP-X to factory settings. During the
reset process the amplifiers will shut off for 5-10 seconds.
•
Vehicle Type - Select the vehicle type from the drop down box, select either
Without OE Amplifier or With OE Amplifier, then click the apply button
.
• Lock Down - Click this button to save the selected settings.
Attention! This button must be selected before closing the app or cycling
the key otherwise all settings will be lost.
•
Save Configuration - Saves the current configuration to the mobile device
.
• Recall Configuration - Recalls a configuration from the mobile device.
10
Continued on the next page
AXDSP-X APP (CONT.)
Configuration (Cont.)
• Apply Configuration - Allows a recalled configuration to the AXDSP-X.
The AXDSP-X will need to be locked down to save the recalled
configuration. This process will shut the amplifier off between 5-10
seconds while the configuration is uploaded to the AXDSP-X.
• About - Displays information about the app, vehicle, AXDSP-X,
and mobile device.
• Set Password - Assign a 4-digit password to lock the AXDSP-X. If no
password is desired, use “0000”. This will clear out any currently set
password. It is not necessary to lock down the AXDSP-X when setting a
password.
Note: A 4-digit only password must be chosen otherwise the interface
will show “password not valid for this device”.
Altri manuali per AX-DSP-X
1
Indice
