Aztech DSL7002GRV(S) Manuale utente
Contents
STEP 1: Equipment Check
STEP 2: Setting Up Your BroadBand Connection
STEP 3: BroadBand Connection Settings for Fibre (Optional)
STEP 4: Logging in to Your SingNet BroadBand
STEP 5: Connecting Wirelessly to SingNet BroadBand (Optional)
STEP 6: Setting Up Your mio Voice
Technical Support Contact Numbers
1
STEP 1: Equipment Check
Dear Customer, this guide has been prepared to help you to install
SingNet BroadBand service and mio Voice services.
The following items are pre-packaged in your Residential Gateway.
Note: Existing Singnet BroadBand, mio Plan or mio Home subscribers should
already have these items connected to their Residential Gateway.
STEP 2: Setting Up Your BroadBand Connection
Using the Telephone Cable
(RJ11), connect the Residential
Gateway’s“DSL” Port to the DSL
Microfilter’s “DSL” port.
Insert the head of the DSL
Microfilter into your Telephone
the wall socket.
Note:
You can connect your telephone into the
DSL Microfilter’s “Phone” port to use
your fixed Phoneline.
Connect Power Adapter to your
Residential Gateway “POWER”
port and the nearest electrical
outlet. Turn “On” the power
at the electrical outlet and the
Residential Gateway
Please wait for approximately 5 minutes.
The “POWER” and the “BROADBAND”
LEDs should now be stable GREEN (not
blinking), except the “ETHERNET” LED,
it should be GREEN and blinking. If not,
please check connections 2.1 to 2.3. Do
NOT proceed to the next section until
you have done so.
LED Check:
2.1
2.2
2.3
3
Using an Ethernet Cable (RJ45),
connect your PC’s “ETHERNET”
port to any of the available
Residential Gateway’s “LOCAL
ETHERNET” ports.
Verify that the “ETHERNET” and
“BROADBAND” LEDs found in
front of the Residential Gateway
are light up in GREEN.
Note:
If the LEDs mentioned in 2.5 are not light
up, please check your connections again
based on 2.1 to 2.4. You may now proceed
to Step 3 once the LEDs are light up.
Optional: If you have subscribed
to mio TV service, please connect
the Set-Top-Box to the Residential
Gateway using the blue ethernet
cable (RJ45) provided.
2.4
2.5
2.6
STEP 3:
Connect the Residential Gateway’s
“BROADBAND” Port to the ONT’s
“LAN 1” Port highlighted in Yellow
using the Ethernet Cable (RJ45).
Note:
Switch off the ONT’s power before you do
the set up.
For mio TV Set-Top-Box, personal
computer or laptop, please connect
it to the “LOCAL ETHERNET” Port
highlighted in yellow.
For mio Voice service, please
connect your phone using a Phone
Cable (RJ11) to the Residential
Gateway’s “VOICE 1&2” Port.
3.1
3.2
3.3
Once Power Adapter is connected,
follow the power up sequence as
below.
Power up the Optical Network Terminal
(ONT). Wait for “POWER” and “PON”
LEDs to turn to stable green light.
Power on the Residential Gateway.
Wait for the “POWER”, “ETHERNET”,
“BROADBAND”, “INTERNET” and “IPTV”
(if applicable) to turn to stable green
light.
Power up you mio TV Set Top Box and
your computer.
Note:
For exStream service, there is no need to
key in user ID and password. All service
credential will be auto push down to your
Residential Gateway.
3.4
BroadBand Connection Settings
for Fibre (Optional)
1.
2.
3.
5
STEP 4: Logging in to Your Singnet BroadBand
Please confirm that you have the following item on hand before attempting
this step.
>> SingNet BroadBand Service Letter - This contains your Username and
Password which will be used for setting up the SingNet BroadBand.
Open your web-browser (e.g. Internet
Explorer). You should now see the
following screen on the left. Click on
“SET UP NOW”.
4.1
Type your User ID and Password as
stated in your Service Letter in the
“Username” and “Password” fields and
click the “Connect” button.
Note:
If you are unable to view the page type the URL
http://192.168.1.254
Note:
The text behind @ maybe different. Please
ensure that you have entered the correct
one as stated in your service letter before
proceeding.
Please wait while SingNet verifies
your account. If you have entered your
“Username” and “Password” correctly,
you will be redirected to the “Setup
Successful” page.
4.2
4.3
The “POWER”, “BROADBAND”,
“ETHERNET” and “INTERNET”
LEDs should now be stable
GREEN (not blinking), except the
“ETHERNET” LED, it should be
GREEN and blinking. If not, please
re-do STEP 4 and ensure that you
enter your USER ID and Password
correctly.
LED Check:
Congratulations! You can now use SingNet BroadBand!
7
Please take note of two numerical codes which are your Network name
and Key with this diagram as a guide.
You may fill in these details on the box below for future references.
Section A: Your Network Name and Key
IMPORTANT!
You will need a wireless adapter (wireless PC card or wireless USB adapter)
or a wireless-enabled Notebook before you can proceed to the next section.
Please refer to your operating system’s instructions:
Section B. if you are using Window’s XP
Section C. if you are using Windows Vista
Section D. if you are using Windows 7
Section E. if you are using Windows 8
Section F. if you are using another wireless manager other than Windows
Network Name (SSID):
Singtel7002(5G)-_____
Singtel7002 - ______
Network Key:
____________________
STEP 5:
Note: The default wireless encryption option is Mixed WPA2/WPA-PSK.
Write the last 4 numbers of your Network
Name here.
Write the 10 digit of your Wireless
Key here.
Connecting Wirelessly to SingNet
BroadBand (Optional)
Section B: If you are using Windows XP
Double click on the wireless icon
on your task bar.
You should see the available
wireless networks, if you are
prompted to use another wireless
manager, please refer to section
E.
Double click the Network Name
of your wireless network (e.g.
SINGTEL-0110) and wait for the
network to be detected.
Note:
Please refer to section A if you are unsure
of your Network Name and try refreshing
your Network List if you do not see it.
Type the 10-Digit Network Key into
the “Network Key” and “Confirm
Network Key” fields. Click on the
“Connect” button to complete the
setup and wait for the network
address to be acquired.
Note:
Please refer to section A if you are unsure
of your Network Key.
4
3
2
1
Indice
Altri manuali Aztech Router di rete
Aztech
Aztech DSL5068EN(1T1R) Manuale utente
Aztech
Aztech HW550-3G Manuale utente
Aztech
Aztech DSL8800GR Istruzioni per l’uso
Aztech
Aztech DSL605E Istruzioni per l’uso
Aztech
Aztech 4-Port Wireless N Router Manuale utente
Aztech
Aztech DSL5008EN Istruzioni per l’uso
Aztech
Aztech DSL5005EN Istruzioni per l’uso
Aztech
Aztech WMB260AC Manuale utente
Aztech
Aztech DSL5029EN(1T1R) Istruzioni per l’uso
Aztech
Aztech DSL1000EW L Guida
Aztech
Aztech HW831 Manuale utente
Aztech
Aztech WL830RT4 Istruzioni per l’uso
Aztech
Aztech na8300 Scheda informativa del prodotto
Aztech
Aztech SDSL Bridge & Router Manuale utente
Aztech
Aztech 700WR-3G Guida utente
Aztech
Aztech ADSL 4 Port Ethernet Router Scheda informativa del prodotto
Aztech
Aztech DSL906 1DA Series Scheda informativa del prodotto
Aztech
Aztech WL730RT4 Manuale utente
Aztech
Aztech HW550-3G Foglio di istruzioni
Aztech
Aztech ADSL2+ Ethernet Router Manuale utente
Manuali Router di rete popolari di altre marche
NETGEAR
NETGEAR FS526T - Switch Manuale utente
Korenix
Korenix JetNet 5710G Series Manuale utente
Automated Logic
Automated Logic ZN551 Manuale del proprietario
Cisco
Cisco ASR 1000 Series Manuale dell'operatore
EnGenius
EnGenius ESR-9710 Manuale utente
Cisco
Cisco 805 Series Istruzioni operative e di sicurezza