AzureWave AW-NM388 Manuale utente
- 1 -
AW-NM388
Wireless LAN & Bluetooth Module IC
For Mobile Phones, DSCs, PMPs and Gaming Devices
XP MFG Tool Command User Guide
Version 0.2
Document
release
Date
Modification
Initials
Approved
Ver. 0.1
2011/07/05
Initial version
Lester Huang
Ivan Chen
Ver. 0.2
2012/01/31
Add Warning Statement
Lester Huang
Ivan Chen
- 2 -
1. AW-NM388 WLAN & Bluetooth MFG Tool Command User Guide
Figur1
When you test AW-NM388, AW-NM388 module put in socket and please connect the B type
USB. It is necessary for two issues. One is for Bluetooth UART to USB interface control and
the other one is apply the voltage for 32.768KHz OSC.
1.1 Step1: Environment set up(Win XP English Ver. is necessary)
(1) Plug the USB cable in the host PC.
(2) Copy the file “sd8787.sys”from the sub folder below:
\MFG-8787-WIFI-SD-BT-SD-WIN-X86-1.2.6.22-14.0.3.p155\bin\lab_tool\drv\WinXP
(Please contact Azurewave FAE for the sub folder) and phase it into the sub folder below:
\Windows\system32\drivers
As figure 2
BT Antenna
B Type USB connector
WIFI AUX Antenna
Antenna Port
WIFI Main Antenna
SDIO Interface
- 3 -
Figure 2
Figure 3
- 4 -
(3) Connect SDIO to the host PC.
(4) Choose “Cancel”for all auto hardware detection.
(5) Install the 8787 SDIO driver following the steps below:
1. Refer to Figure 3 for the indication of the 8787 device in the Windows Device manager.
2. At this point the host PC will auto detect 3 Marvell 802.11 SDIO devices.
3. Only one Marvell 802.11 SDIO is work, others can be ignored.
4. Update Driver following the picture below
Figure 4
- 5 -
Figure 5
Figure 6
- 6 -
5. Browse the driver from the folder as below: (Figure 6)
\MFG-8787-WIFI-SD-BT-SD-WIN-X86-1.2.6.22-14.0.3.p155\bin\lab_tool\drv\WinXP
6. Installation will be successful as Figure 7 showed. WiFi is done.
Figure 7
7. Setup Bluetooth UART to USB driver. FTDI IC is used in this adapter board.
8. Please indicated the install path to the FTDI folder (Check Azurewave FAE to get this one)
9. After installing, you can find the new comport showing up in the devices manager as figure 8.
- 7 -
Figure 8
1.2 Step2: Opening MFG Tool
(1) Please make sure the AW-NM388 is enabling (check OS device manger).
(2) Opening MFG tool, please double click on the “DutApiSDUART8787.exe.” in this sub folder:
(3) \ MFG-8787-WIFI-SD-BT-SD-WIN-X86-1.2.6.22-14.0.3.p155\bin\labtool
1.3 Step3: Initial Command
As the information showed on your screen, please enter these commands below to start your test.
(Figure 9)
Command: 1 Wi-Fi testing mode
Command: 2 BT testing mode
Command: 3 FM testing mode
- 8 -
Figure 9
1.3 Step3: Generate 802.11 b/g/n Packet
(1)Command:
Select WIFI Main Antenna:
69 90000200 40
69 90000208 0
69 9000020C 8
69 80002200 FFFF
Select WIFI AUX Antenna:
69 90000200 400
69 90000208 0
69 9000020C 20
69 80002200 FFFF
(2)Command: 22 1 12 1
22: Initial transmit power in the antenna
1: Set the wanted channel (1~14 for B/G/N mode)
12: Set the wanted power, typically G mode: 12 dBm/ B mode: 15 dBm
1: Set the mode, 1G mode & N mode , 0B mode
- 9 -
(3)Command: 112 0 (only for N mode)
112: N mode HT20/40.
0: for HT20/40. 0HT20, 1HT40
(4)Command: 25 1 13
25: Set duty cycle, packet mode.
1: Data rate enable
13: Data rate set up
A mode &B mode & G mode
1Mbps
5.5Mbps
11Mbps
6Mbps
9Mbps
12Mbps
18Mbps
24Mbps
1
3
4
6
7
8
9
10
36Mbps
48Mbps
54Mbps
11
12
13
N mode
MCS0
MCS1
MCS2
MCS3
MCS4
MCS5
MCS6
MCS7
MCS8
15
16
17
18
19
20
21
22
23
After you type above command, you can measure the 802.11b/g/n packet by your RF test instrument (exp:
Agilent 4010, IQview…).
(5)Command: 25 0
Stop transmitting packet signal.
1.4 Step4: Generate 802.11b/g/n continuous symbol
(1)Please re-type the Step3 (1)~(5) commands.
(2)Command 17 1 13
17: Set continuous mode.
1: Enable data rate
13: 54 Mbps, other data rate, please refer the above table.
After you type above command, you can measure the 802.11b/g continuous symbol in your RF test
instrument.
(3)Command 17 0
Stop transmitting continuous signal
- 10 -
1.5 Step5: Test RX sensitivity
Before test RX, the Marvell standard waveform is needed. Please contact
Azurewave FAE for this issue.
(1)Command:
Select WIFI Main Antenna:
69 90000200 40
69 90000208 0
69 9000020C 8
69 80002200 FFFF
Select WIFI AUX Antenna:
69 90000200 400
69 90000208 0
69 9000020C 20
69 80002200 FFFF
(2)Command 12 1
12: Choose RX text channel
1: Channel number, (1~14 for B/G/N mode)
(3) Command: 112 0 (only for N mode)
112: N mode HT20/40.
0: for HT20/40. 0HT20, 1HT40
(4) 31: Clear all the received packets.
(6) 32: Check the received packets.
1.6 Others Commands
(1) Command 45Check the MAC
(2) Command 99Quit the test mode/ Quit the MFG tool
Indice
Altri manuali AzureWave Adattatore
AzureWave
AzureWave AW-NU231-D Manuale utente
AzureWave
AzureWave AW-NU138 Manuale utente
AzureWave
AzureWave uSD-15x15 Manuale utente
AzureWave
AzureWave AW-NU706H Manuale utente
AzureWave
AzureWave AW-AM457-D-EVB Manuale utente
AzureWave
AzureWave AW-NU221 Manuale utente
AzureWave
AzureWave AW-CU474-UNO Manuale utente
