B-52 MP 5712B Manuale utente
MOBILE ENTERTAINMENT SYSTEM
INSTRUCTIONS MANUAL
MP 5712B
CAR CD/ MP3 PLAYER / RECEIVER
USB /SD /MMC /SLOT/ BLUETOOTH
www.b52audio.com
INSTRUCTIONS MANUAL 02 - 20
MANUAL DE INSTRUCCIONES 21 - 40
MANUAL DE INSTRUÇÕES 41 - 61
ENGLISH
MUTE
LOUD
MP 5712B
Installation
Additional information
General operations
Radio operations
CD/SD/MMC/USB Operations
MP3 WMA overview
Remote control layout
Specification
Before playing discs
Trouble shooting
Bluetooth
INDEX
2
03
05
06
09
11
14
15
17
18
19
20
PRECAUTIONS
Choose the moun ting location where the unit will not interfere with the normal driving function
of the driver.
Bef ore final ly installing the unit, connect the wiring tempor arily and make sure it is all
connected up properly and the unit and the system work properly.
Use only the parts included with the unit to ensure proper installation. The use of unauthorized
parts can cause mal functions.
Con sult with your nearest dealer if installation requires the drilling of holes or other
modifications of the vehicle.
Install the unit where it does not get in the driver’s way and cannot injure the passenger if there
is a sudden stop. Like an emergency stop.
If installation angle exceeds 30 from horizontal, the unit might not give its optimum
performance.
Avoid installing the unit where it would be subject to high temperature, suchas from direct
sunlight, or from hot air, form the heater, or where it would be subject to dust, dirt or excessive
vibration. Do not expose this equipment to rain or moisture.
DIN FRON T-MOU NT (Method A)
Installing the unit
1. Dashboard
2. Holder
After inserting the holder into
the dashboard, select the
appropriate tab according to
the thickness of the dashboard
material and bend them
inwards to secure the holder in
(Fig. 1) place.
3. Screw
INSTALLATION
30
0
(Fig. 1)
12
3
3
1. Dashboard
2. Nut (5mm)
3. Spring Washer
4. Screw (5 x 25mm)
5. Screw
6. Strap
Be sure to use the strap to
secure the back of the unit in
place. The strap can be bent by
hand to the desired angle.
7. Plain Washer
INPUT THE SD CARD
The SD oblique angle keeps
rightward exposure, put into
the SD slot and press it again
to eject.
1. Frame
2. Insert fingers into the groove in the front
of frame and pul l out to remove the frame.
(When reatt achi ng the frame, point the
side with a Groove dow nwards and attach
it. )
3. Lever
Insert the levers supp lied with the
unit into the grooves at both sides of
the unit and shown in figure until they click.
Pulling the levers makes posible to remove
the unit from the dashboard.
DIN REAR-MOUNT (Method B)
Installation using the screw holes on
the sides of the unit.
INSTALLATION
1
2
3
4
5
6
7
(Fig.2)
2
1
3
(Fig.3)
Removing
the
uni t
2
3
2
4
ADDITIONAL INFORMATION
SPEAKER CONNECTION
HOW TO INSTALL AND REMOVE THE FRONT PANEL
INSTALLING THE FRONT PANEL
To install the front panel, insert the panel into the housing and make sure the panel is properly
installed, otherwise, abnormalities occurs on the display or some keys will not function properly
1
2
3
5
GENERAL OPERATIONS
FRONT PANEL LAYOUT
1. POWER BUTTON
2. RELEASE BUTTON
3. VOLUME/ SEL BUTTON
4. MUTE BOTTON
5. MODE SWITCH
6. DISPLAY BUTTON
7. LCD DISPLAY
8. FLASHING LED
9. RESET BUTTON
10. BAND SWITCH
11. TUNE SEEK Y TRACK FORWARD BUTTON
12.TUNE SEEK Y TRACK REVERSE BUTTON
13. AUTOMATICALLY MEMORY STORING
14. PLAY/PAUSE Y PRESET BUTTON 1
15. INTRO Y PRESET BUTTON 2
16. REPEAT Y PRESET BUTTON 3
17. RANDOM Y PRESET BUTTON 4
18. PRESET BUTTON 5
19. PRESET BUTTON 6
20. ST/MO BUTTON
21. LOC/DX BUTTON
22. LOUDNESS BUTTON
23. EJECT KNOB
24. CD SLOT
25. REMOTE CONTROL SENSOR
26. USB CONNECTER
27. SD/MMC SLOT
28. AUX IN JACK
29. SCN BUTTON
6
MUTE
LOUD
MP 5712B
POWER ON/OFF
Press any button to turn the unit on. Press and hold POWER button to turn off the unit.
Note: After the unit is off, the volume level and radio current settings will be memorized, and
when you turn the unit on it will resume the stored status, which you set.
FRONT PANEL RELEASE
Press REL button (2) to detach the removable front panel
SOUND ADJUSTMENT
Turn on (3) can adjust the desired volume quality.
A).Press SEL button (3)will change in the following order.
Option:
VOLUME CONTROL /SELECT
Rotating this knob, you can adjust VOL/BASS/TREB/BAL/FAD . To select the functions, press the
VOL knob shortly until the desired functions are shown on the display.
Increase or decrease the volume by turn the VOL knob right or left. These buttons can be used
to adjust the BASS, TREBLE, BALANCE and FADER.
BASS
Press VOL/ SEL button(3) one time. Adjust bass level by using VOL/ SEL(3)Knob.
TREBLE
Press VOL/ SEL button(3) two times. Adjust treble level by using VOL/ SEL(3) Knob
BALANCE
Press VOL/ SEL button(3) three times. Adjust sound balance between left and right speakers by
using VOL/ SEL(3)Knob.
FADER
Press SEL button (3) four times. Adjust sound balance between front and rear speakers by using
VOL/ SEL(3)Knob.
MUTE
Press MUTE button (4) to mute down the sound. Press it again to release this mode and recover
previous volumen level.
OTHERS ADJUSTMENT
Press VOL/SEL button (3) for several seconds, it is activated as cyclical mode of following
functions for user´s selection.
VOL BAS TRE BAL FAD
7
(Volume) (Bass)(Treble) (Balance) (Fader)
Press and hold this button will go to different modes:
Press and hold will go to DSP mode automatically:
By turning this function button to chose Flat, CLASSIC, Pop and Rock.
By press the function button to select your favoryte DSP mode.
When in the DSP mode, press the function button once will to ESP mode:
By turning the function button to choose 12 seconds ESP.
Vy press the function button to select your desire ESP seconds.
When in the DSP mode, press the function button twice will go to BEEP mode
(the key pad tone) by turning the function button to choose on or off by press
The function button to selecto n or off.
VOL LAST/ADJUST
This function allows to set the volumen level of the unit after it was turned off and the turne don
again. Choose VOL LAST if you want the volumen level to be the same as it was before turning off.
VOL ADJUST allows to choose volumen level.
SEEK MODE
SEEK 1: When SEEK 1 mode is activated, AUTO SEEK SCAN is stopped when station is detected
even user still push SEEK button.
SEEK 2: Auto SEEK SCAN is not stopped even if station is detected if user pushes SEEK button.
When releases SEEK button, the stop when station is detected.
SELECT MODE
By pressing this button(5) to go to different function mode:
- Tuner (radio)
- CD (MP3 CD) to go to this mode must be have a CD in.
- Memory Card to go to this mode must be have a Memory Card in.
- USB to go to this mode USB device must be connected.
- AUX in put
DISPLAY
Press DISP button (6) to operate as the conversion of each display mode as follow:
- Time is displayed for 5 sec when DISP key is pressed, and it returns to its previous display
(Folder, File name...) unless DISP key is pressed again.
3) From the clock mode, when DISP Key is pressed for longer than 1sec, clock mode switches to
clock Adjusting mode and the clock display begins flashing. At this time clock can be changed by
pressing ( + / - ) , or the ENCODER VOLUME.
LIQUID CRYSTAL DISPLAY
Exhibit current frequency and activated functions on the display (7).
FLASHING LED
If the front panel does not install in the main unit, the LED (8) will be flashing.
8
BAND SELECTION
At tuner mode, press BAND button (10) to select the desired band. The
reception band will change in the following order:
STATION SELECTION
Press TUNE/SEEK/TRACK FORWARD button (11) or TUNE/SEEK/TRACK REVERSE button (12)
shortly for manual tuning function.
Press for several seconds the automatic tuning mode ( SEEK
mode) is selected.
AUTOMATICALLY MEMORY STORING & PROGRAM SCANNING
- Automatically Memory Storing
Press AMS(MP3) button (13) for several seconds, the radio searches from the current frequency
and checks the signal strength until one cycle search is finished.
And then 6 strongest stations are stored into the corresponding preset number Button
- Program Scanning
Press AMS(MP3) button (13) shortly to scan preset station. When the field strength level is more
than the threshold level of stop level, the radio is holding at that preset number for several seconds
with releasing mute, then searches again.
STATION STORING
Press preset button (14~19)
1) RADIO MODE. M1 ~ M6
- PRESET MEMORY is loaded when key is pressed for less than 1 second.
- PRESET MEMORY is saved when key is pressed for longer than 1 sec.
2) CD/ MP3 / FLASH MP3 PLAY / PAUSE Press preset button (14) is activated. During a PAUSE,
DISC INDICATOR flashes.
TOP - First song will play whe n Top key is pressed for longer than 0.5sec during play.
INT
Press preset button (15): During INTRO ON, INT indicator comes on and
begins playing the first 10sec of each song, until the last song is played. It begins
playing the entire track from where INT started
MO/ST SELECTOR
Press ST (20) button to select MONO or STEREO mode.
When “ST” appears in the LCD display. During the player mode, press the button to switch left
speaker / right speaker/stereo.
RADIO OPERATIONS
9
LOC/DX SELECTOR
Press LOC (21) button to select strong or weak station reception. It is set to LOC mode when LOC
(21) button is first pressed. “LOC” appears and only local station is available. It is switched to DX
mode when LOC (21) button is pressed again. Both distance and local stations can be received.
LOUDNESS ON/OFF
Press LOU (22) button to increase the low frequency. This can improve the sensitivity of your
ears. And “LOUD” appears in the LCD when the loudness mode is activated.
SCAN
Press scan button (29) to search radio station.When a station signal strength
level more than the level to stop.The radio will playing the station for 5
seconds and the frequency blinking on the LCD at the same time.
Press and hold scan button (29) more than 3 seconds to select the station which
you desired.The radio will start play the station.
AREA USA/EUR SETUP
In Radio mode. Press SEL button for several seconds. LCD with show from DSP OFF/ON AREA USA/
EUR. At AREA USA/EUR. You can use VOL +/- to select the AREA frequency.
10
Indice
Lingue:
Altri manuali B-52 Impianto stereo per auto
