Backyard YardLine ASTON Manuale utente
BEFORE YOU BEGIN
IMPORTANT!
READ INSTRUCTIONS THOROUGHLY PRIOR TO BEGINNING ASSEMBLY.
- CUSTOMER SERVICE -
Call: 1-800-844-9273 email: customerservice@backyardproductsllc.com
•BUILDINGRESTRICTIONSANDAPPROVALS
Be sure to check with local building department and homeowners association for specic restrictions and/ or requirements before building
.•ENGINEEREDDRAWINGS
Contact our Customer Service Team if engineered drawings are needed to pull local permits.
•SURFACEPREPARATION
To ensure proper assembly you must build your shed on a level surface. Recommended methods and materials to level your shed are
listed on page 7.
•CHECKALLPARTS
Inventory all parts listed on pages 4 - 6. Contact our Customer Service Team if any parts are missing or damaged.
•ADDITIONALMATERIALS
You will need additional materials to complete your shed. See page 3 for required and optional materials and quantities.
10-30-2017
KEEP THIS MANUAL FOR FUTURE REFERENCE
ACTUAL FLOOR SIZE IS 120" x 90" (304,8 x 228,6 cm)
16572
ASTON 10' x 7'-6" (304,8 x 228,6 cm)
ASSEMBLY MANUAL
ABackyardProductsCompany
2
TOOLS
Safety! Always use approved safety glasses during assembly.
OptionalRequired
HELPFUL REMINDER SYMBOLS
Look for these symbols for helpful reminders throughout this manual.
ORIENT LUMBER AND TRIM FOR BEST APPEARANCE
= Assistance Required; two or more people.
= Ensure squareness.
= Important required step or operation.
= Helpful assembly hint.
= Mark part with pencil.
= Beginning of steps for assembly or installation.
= You have nished the assembly or installation.
= Level
❑Gloves
Framing lumber is graded for structural strength and not appearance. Exterior trim is graded for one good side.
Always install the material leaving the best edge and best surface visible. Please remember that these blemishes in no way
negatively affect the strength or integrity of our product. (See Fig. A, B, C.)
A
❑Safety Glasses
❑Tape Measure
❑Paint Tools
❑Ladder
❑Caulk Gun
❑Hammer
❑Level
FINISH
BEGIN
❑Pencil
❑Phillips
Screwdriver
❑ Drill / Driver
❑ 1/4" Drill Bit
❑ 3/8" Drill Bit
❑ 1/2" Drill Bit
❑#2 Philips Drive Bit
❑ Tool Belt/
Nail Pouch
❑Chalk Line
❑Nail Gun
• gun nails
❑Tin Snips
(for drip edge)
❑ Square or
❑Utility Knife
❑Shingle Blades
B C
3
COMPLETING YOUR SHED
You will need these additional materials:
TO VALIDATE YOUR WARRANTY YOU MUST USE THE FOLLOWING:
FOUNDATION OR FLOOR MATERIALS
ADDITIONAL MATERIALS
DRIPEDGE.....................50Feet #15ROOFINGFELT
To cover 99 Sq. Ft. of roof area.
1"GALVANIZEDROOFINGNAILS.........1/4Lb
For roong felt.
REFER TO THE BACK OF THIS MANUAL AND THE MANUFACTURER’S INSTRUCTIONS
FOR INSTALLATION OF SHINGLES, DRIP EDGE AND FELT.
3-TABSHINGLES............................4Bundles
PAINTFORSIDING..........................2Gallons
Use 100% acrylic latex exterior paint. (2) coats recommended.
CAULK.................................................3Tubes
Use acrylic latex exterior caulk that is paintable.
1"GALVANIZEDROOFINGNAILS....3Lbs
For shingles.
PAINTFORTRIM.............................1Quart
Use 100% acrylic latex exterior paint.
WOODGLUE.......................ExteriorRated
REINFORCED WOOD FLOOR FRAME (OPTIONAL)
IMPORTANT! The included oor has been designed for general use. Depending on your specic use you may want to construct a
heavy duty oor frame by adding additional oor joists (shown below). Below is a list of additional materials (not included):
x2
x8
2 x 4 x 87" (5 x 10 x 221 cm) Treated Lumber
ea. 3" (7,6 cm) Hot Dipped Galvanized Nails
• This shed kit includes a complete wood oor system.
• This shed kit does not include ANY leveling materials.
•SeetheFLOORLEVELINGsectiononpage7forrecommendedmethodsandsuggestedmaterialstoproperlylevelyour
oor,asthiswillvarydependingonyourspecicsite.
Optional 12" (30,1 cm) spacing.
• Standard spacing is 16" (40,7 cm).
WOODSIZECONVERSIONCHART
NominalBoardSize ActualSize
1" x 4".................3/4" x 3-1/2" (1,9 x 8,9 cm)
2" x 4"..............1-1/2" x 3-1/2" (3,8 x 8,9 cm)
2" x 3"..............1-1/2" x 2-1/2" (3,8 x 6,3 cm)
1" x 3".................3/4" x 2-1/2" (3,8 x 6,3 cm)
PARTS IDENTIFICATION AND SIZES
RS RS
Part identication
letters are stamped on some parts.
Check these locations for
part stamp.
Treated lumber is stamped:
Alltreatedlumber
isstamped:
WALLS
x4 2 x 4 x 86" (5,1 x 10,2 x 218,4 cm)
BLA
x2 2 x 4 x 79-1/8" (5,1 x 10,2 x 201,3 cm)
BJA
x2 2 x 4 x 74-1/4" (5,1 x 10,2 x 188,6 cm)
BNA
x2 2 x 4 x 72-5/8" (5,1 x 10,2 x 184,5 cm)
BFA
x3 2 x 4 x 72" (5,1 x 10,2 x 91,4 cm)
TM
x2 2 x 4 x 68" (5,1 x 10,2 x 172,7 cm)
UM
PARTS LIST
INVENTORY YOUR PARTS before you begin.
We suggest sorting parts by the category they are listed in.
RAFTERS
x2 1 x 3 x 72" (2,5 x 7,6 x 182,8 cm)
x1 1 x 3 x 5" (2,5 x 7,6 x 12,7 cm)
TRIM
x2 19/32 x 3-1/2 x 48" (1,5 x 8,8 x 121,9 cm)
x1 19/32 x 3-1/2 x 52 - 3/8" (1,5 x 8,8 x 133 cm)
x2 2 x 3 x 33-1/8" (5,1 x 7,6 x 84,1 cm)
x1
x4 19/32 x 2 - 1/2 x 9" (1,5 x 6,3 x 22,9 cm)
x9 2 x 3 x 10-1/2" (5,1 x 7,6 x 26,7 cm)
x2 1 x 3 x 33 - 1/8" (2,5 x 7,6 x 84,1 cm)
BPA
x1 19/32 x 3-1/2 x 35-1/4" (1,5 x 8,8 x 89,5 cm)
BYA
x6
x3
x2
x2
2 x 4 x 64" (5,1 x 10,2 x 162,5 cm)
2 x 4 x 48" (5,1 x 10,2 x 121,9 cm)
2 x 4 x 28" (5,1 x 10,2 x 71,1 cm)
2 x 4 x 45 - 5/8" (5,1 x 10,2 x 115,8 cm)
UX
SP
RR
BUA
BQA
FS
EY
x2 2 x 4 x 85-1/2" (5,1 x 10,2 x 217,2 cm)
BKA
2 x 4 x 16 - 1/2" (5,1 x 10,2 x 41,9 cm)
x4
3/4"
(1,9 cm)
RD
BMA
GAA
BRA
HJ
x9 2 x 4 x 93-3/16" (1,5 x 10,2 x 236,7 cm)
BOA
2 x 3 x 35-1/4" (5,1 x 7,6 x 89,5 cm)
ZT
x1 19/32 x 3 - 1/2 x 59 - 1/4" (1,5 x 8,8 x 150,4 cm)
BXR
x1 19/32 x 3 - 1/2 x 59 - 1/4" (1,5 x 8,8 x 150,4 cm)
BXL
x1 UN 2 x 4 x 94-1/2" (5,1 x 10,2 x 240 cm)
4
FLOOR
x2
2 x 4 x 87" (5,1 x 10,2 x 220,9 cm)
x2 2 x 4 x 48" (5,1 x 10,2 x 121,9 cm)
x9
2 x 4 x 72" (5,1 x 10,2 x 182,8 cm)
SOFFIT
DOOR
PARTS LIST continued...
x2
TRIM
CORNER/FREIZE TRIM
OY 2 x 3 x 72" (5,1 x 7,6 x 182,8 cm)
19/32 x 3-1/2 x 96" (1,5 x 8,8 x 243,8 cm)
19/32 x 3-1/2 x 80" (1,5 x 8,8 x 203,2 cm)
19/32 x 2-1/2 x 91" (1,5 x 6,3 x 231,1 cm)
x1
x1
x2
BTA
BSA
ZX
x1 PT 2 x 3 x 96" (5,1 x 7,6 x 243,8 cm)
35-3/4 x 10-3/8 x 3/8" (90,8 x 26,3 x 1 cm)
x1
95-3/8 x 10-3/8 x 3/8" (242,2 x 26,3 x 1 cm)
x1
95-1/2 x 5-1/4 x 3/8" (242,5 x 13,3 x 1 cm)
x2
19/32 x 2-1/2 x 26-5/8" (1,5 x 6,3 x 67,6 cm)
x4 AH
x2 OO 2 x 3 x 69" (5,1 x 7,6 x 175,2 cm)
x1 3/8 x 2 x 25-3/8" (0,9 x 5,1 x 64,4 cm)
x2 3/8 x 2 x 68-3/4" (0,9 x 5,1 x 174,6 cm)
x1 3/8 x 2 x 69-1/4" (0,9 x 5,1 x 175,8 cm)
x1 3/8 x 2 x 69-1/4" (0,9 x 5,1 x 175,8 cm)
x2 3/8 x 2 x 91-1/4" (0,9 x 5,1 x 231,7 cm)
x1 3/8 x 2 x 93-1/4" (0,9 x 5,1 x 236,8 cm)
x1 3/8 x 2 x 93-1/4" (0,9 x 5,1 x 236,8 cm)
x1 3/8 x 2 x 96" (0,9 x 5,1 x 243,8 cm)
5
PANEL PARTS LIST
ROOF PANELS
FLOOR
NOTE:Panelpartsarenotstamped.
Floorpanelsare5/8"(1,6cm)thick.Roofpanelsare7/16"(1,1cm)thick.
7/16 x 11-7/8 x 96"
(1,1 x 30,2 x 243,8 cm)
x1
7/16 x 11-7/8 x 35-7/8"
(1,1 x 30,2 x 91,1 cm)
x1
7/16 x 35-7/8 x 96"
(1,1 x 91,1 x 243,8 cm)
x1
7/16 x 48 x 96"
(1,1 x 121,9 x 243,8 cm)
x2
5/8 x 23-7/8 x 90"
(1,5 x 60,6 x 228,6 cm)
x1
5/8 x 42 x 96"
(1,5 x 106,6 x 243,8 cm)
x1
5/8 x 48 x 96"
(1,5 x 121,9 x 243,8 cm)
x1
x2
3/8 x 11-7/8 x 96"
(1 x 30,1 x 243,8 cm)
WALL PANEL & DOORS PARTS LIST
x1
LEFTDOOR
x1
RIGHTDOOR
x2 BOXES
x3 BOXES
x210
x180
NAIL BOXES
VENT, DOOR HARDWARE, AND WINDOW
FASTENER/HARDWARE BAG
x2
3/8 x 48 x 72"
(1 x 113,3 x 121,9 cm)
x1
3/8 x 42 x 83-1/8"
(1 x 106,6x 211,1 cm)
x1
3/8 x 48 x 96"
(1 x 121,9x 243,8 cm)
x1
3/8 x 48 x 96"
(1 x 121,9x 243,8 cm)
x1
3/8 x 42 x 83-1/8"
(1 x 106,6x 211,1 cm)
x1
3/8 x 23-7/8 x 72"
(1 x 60,6 x 182,9 cm)
x1
3/8 x 48 x 96"
(1 x 121,9x 243,8 cm)
x1
3/8 x 48 x 96"
(1 x 121,9x 243,8 cm)
6
2" (5,1 cm)
3" (7,6 cm)
x75
x56
x88
x2 1-1/4" (3,2 cm)
3/4" (1,9 cm)
2" (5,0 cm)
3" (7,6 cm)
2" (5,1 cm)
1-1/2" (3,8 cm)
x1
x2
x8
x3
x2
8 x 16"
(20,3 x 35,6 cm)
1/2" (1,2 cm)
x12
1" (2,5 cm)
x2
1-1/2" (3,8 cm)
9 X 27" (22,8 x 68,5 cm)
7
DOOR
FLOOR LEVELING OPTIONS
There are multiple ways to level your oor frame. Our recommended leveling method is shown below.
Leveling materials are not included in this kit.
PREFERRED METHOD - 4x4 TREATED RUNNERS
Measurementsto
centerof4x4's.
• 3" Screws angled into 4x4.
• (2) at each point frame
•and 4x4 touch.
• Level under 4x4 runners only.
• Locate leveling material 12" from ends of runners and no more than 48" apart.
• Asphalt shingles should be used between 4x4 runners and blocks or treated lumber. Never use
shingles in direct contact with ground.
• For best results and aiding in water drainage use gravel under each concrete block.
LEVELINGMETHODS
• If you are building your shed on a concrete foundation see the following page.
CONCRETE
MATERIALREQUIRED
x2 4" x 4" x 10' (10 x 10 x 304,8 cm)Treated Lumber
FastenersforFrameto4"x4".
(3" Screws shown as one option.) Minimum (40) 3" screws / exterior grade.
Useonlywoodtreatedforgroundcontactandfastenersapprovedforusewithtreatedwood.
Alwayssupportframeseams.
Levelinghigherthan16"notrecommended.
LEVELINGMATERIALS
Gravel
2x4 Treated Lumber
Solid Masonry Blocks in 1", 2", 4" or 8" thickness
Asphalt Shingles
8" Block
4" Block
Gravel
Gravel
Do not exceed 16".
4x4 Runner
Shingle
Shingle
Maximum between leveling
material locations.
48"
12"
2x4 Treated Lumber
2" Block
Level
12"
12"
(30,5 cm)
12"
(30,5 cm)
8
CONCRETE FOUNDATION
Your kit contains all materials to construct a wooden oor. If you choose to install your kit
on a concrete slab refer to the diagram below.
• A treated 2 x 4" (5,1 x 10,2 cm) sill plate is required when installing your shed on concrete. Hint:Usetreatedlumberinyourkitor
purchasefulllengthtreatedlumber.
• Use a high quality exterior grade caulk beneath all sill plates.
• Fasten 2 x 4" (5,1 x 10,2 cm) sill plates to slab using approved concrete anchors (fastenersnotincluded).
• Check local code for concrete foundation requirements.
NOTES
Allow new concrete slabs to cure for at least seven (7) days.
2" x 4" x 10'-0" (5,1 x 10,2 x 304,8 cm)
2" x 4" x 7'-6" (5,1 x 10,2 x 229,6 cm)
Caulk
Requires:
x2
x2
x1
MUSTbetreatedlumber.
MUSTbetreatedlumber.
120"(243,9cm)
120"x90"(304,8x228,6cm) 83"(210,9cm)
10'x7'-6"(304,8x228,6cm) 90"(228,6cm)
AActualSize B CBuildingSize
A
B
C
4"
(10,2 cm)
3-1/2"
(8,9 cm)
DOOR
TreatedSillPlate
Caulkbetweensill
plateandconcrete.
9
DOOR
3" (7,6 cm)
x9
x2
x40
2 x 4 x 87" (5,1 x 10,2 x 221 cm)
2 x 4 x 72" (5,1 x 10,2 x 182,9 cm)
x2 2 x 4 x 48" (5,1 x 10,2 x 121,9 cm)
PARTSREQUIRED:
Center
onmarks
DOOR
FLOOR FRAME
Flush
Flush
Look for
Stamp
TREATED
HINT:
Foreasiernailing
standonframe.
2
1
Use two 3" nails at each mark.
Orient parts as shown on at surface. Measure and mark.
BEGIN
You have nished your oor frame.
Proceed to level and square frame.
FINISH
3
Notethismeasurement
TOENAILING
48"
(121,9 cm)
32"
(81,3 cm)
16"
(40,6 cm)
16"
(40,6 cm)
48"
(121,9 cm)
64"
(162,6 cm)
80"
(203,2 cm)
90"
(228,6 cm)
87"
(221 cm)
96"
(243,8 cm)
107-5/8"
(273,4 cm)
120"
(304,8 cm)
72"
(182,9 cm)
72"
(182,9 cm)
12-1/4"
(31 cm) 11-5/8"
(29,5 cm)
10
DOOR
FINISH
5
LEVEL AND SQUARE FLOOR FRAME
Before attaching oor decking, it is important to level and square the oor frame.
A level and square oor frame is required to correctly construct your shed.
BEGIN
2
3
4
1
Use level and check the frame is level before applying oor panels.
Check for frame squareness by measuring diagonally across corners. If the measurements are the
same, the frame is square. The diagonal measurement will be approximately 150" (381 cm).
When the frame is level and square secure one side of frame to the 4x4 runners using one fastener at
ends of each runner. Move to the opposite end of the frame. Secure the frame to 4x4 runners with one
fastener at ends of each runner making sure the frame remains square (Fig.A).
Once the oor frame is level and square fasten the frame to the 4x4 runners at each point the frame
contacts the 4x4 runners.
See page 7 for the preferred oor leveling method.
First,secure
atendswith
onefastener.
Second,secure
atendswith
onefastener.
150"
(381 cm)
150"
(381 cm)
Fig.A
Indice
Altri manuali Backyard Deposito all'aperto
