BAFANG FM G312.250.D Manuale utente
1
DEALER MANUAL FOR MOTOR
BF-DM-C-FM G312-D-EN December 2022
6.1 Introduction
6.2 Specifications 3
6.2.1 Outline and geometric size 3
6.2.2 Surface 3
6.2.3 Storage Information 3
6.3 Drive Unit Installation 4
6.3.1 List of Tools to be used 4
6.3.2 Motor Installation 4
6.4 Maintenance 5
CONTENT
6 DEALER MANUAL FOR H400
(FM G312.250.D)
2BF-DM-C-FM G312-D-EN December 2022
6.1 INTRODUCTION
•Product Model
FM G312.250.D
•Scope
Applies only to electrically powered pedelecs
developed or licensed by Bafang. It is suitable
for city and trekking bikes, which have been
developed for road use. The engine is not
suitable for sport competitions.
•Identification
The following graphic, is the identification
numbers of the product, which are shown on
the housing:
Note: Content in the label is important informa-
tion about this product. Please do not remove
the information from the motor.
3
DEALER MANUAL FOR MOTOR
BF-DM-C-FM G312-D-EN December 2022
6.2 SPECIFICATIONS
Motor model: FM G312.250.D
Rated power (W) 250
Rated voltage (V) 36
Waterproof IPX5
Certification CE-EMC
Outdoor Temperatures -20℃~45℃
6.2.1 Outline and geometric size
OLD: 100mm
Shaft length: 142mm
Motor cable length: L=250mm (Optional)
6.2.2 Surface
Shockproof black and silver coating
6.2.3 Storage Information
The pedelec should be stored in a ventilated dry room. Avoid storing the pedelec near strong magnetic
objects.
4BF-DM-C-FM G312-D-EN December 2022
6.3 DRIVE UNIT INSTALLATION
6.3.1 List of Tools to be used
Use of the Tools Tools
To fasten BC3/8 cap lock nuts Open-end wrench
To fasten the screws on disk brake Internal hex wrench
6.3.2 Motor Installation
1. First fix the disc brake on to non-cable side
of the motor and insert the stop pin on to
the shaft.
2. Insert the motor into the frame.
3. Mount one 2mm washer on both sides of
the frame.
4. Fasten clockwise BC3/8 cap lock nut with
open-end wrench at both ends of the mo-
tor. Torque requirement: 30-36N.m.
5
DEALER MANUAL FOR MOTOR
BF-DM-C-FM G312-D-EN December 2022
6.4 MAINTENANCE
• Maintenance must be carried out by autho-
rized personnel with the correct equipment.
• Do not disassemble the motor.
• Do not use thinners or other solvents to
clean the components. Such substances can
damage the surfaces.
• Avoid water submerging, to keep the com-
ponents protected.
• Avoid using high-pressure cleaning jets.
• For prolonged storage, turn off the battery
and avoid storing near heat sources.
Indice
Altri manuali BAFANG Motore
BAFANG
BAFANG H600 Manuale utente
BAFANG
BAFANG FM G320.250.R Manuale utente
BAFANG
BAFANG MAX Drive System Manuale utente
BAFANG
BAFANG H610 Manuale utente
BAFANG
BAFANG H620 Manuale utente
BAFANG
BAFANG H300 Manuale utente
BAFANG
BAFANG H400 Manuale utente
BAFANG
BAFANG MM G532.250.C Manuale utente
BAFANG
BAFANG MM G510.750.C Manuale utente
BAFANG
BAFANG MM G333.250.C Manuale utente
