BAFANG DP E162.CAN Manuale utente
1
BF-DM-C-DP E162&E163-EN November 2022
DEALER MANUAL FOR DISPLAY
CONTENT
7.1 Important Notice 2
7.2 Introduction of Display 2
7.3 Product Description 3
7.3.1 Specifications 3
7.3.2 Functional Overview 3
7.4 Display Installation 3
7.4.1 Installation Position 3
7.4.2 Installation Steps 3
7.5 Display 4
7.6 Key Definition 4
7.7 Normal Operation 5
7.7.1 Power On/Off 5
7.7.2 Support Level Selection 5
7.7.3 Headlight/ Backlight 5
7.7.4 Battery Capacity Indication 6
7.7.5 Bluetooth Indication 6
7.8 Error Code Definition 7
7 DEALER MANUAL FOR
DP E162.CAN/ DP E163.CAN
2BF-DM-C-DP E162&E163-EN November 2022
7.2 INTRODUCTION OF DISPLAY
• Model: DP E162.C/ DP E163.CAN
• Appearance:
• Identification:
Note: Please keep the QR code label attached
to the display cable. The information from the
label is used for software update.
7.1 IMPORTANT NOTICE
• If the error information from the display
cannot be corrected according to the inst-
ructions, please contact your retailer.
• The product is designed to be waterproof. It
is highly recommended to avoid submerging
the display under water.
• Do not clean the display with a steam jet,
high-pressure cleaner or water hose.
• Please use this product with care.
• Do not use thinners or other solvents to
clean the display. Such substances can
damage the surfaces.
• Warranty is not included due to wear and
normal use and aging.
PD031505
DPE162CF80101.0
PD031505
DPE163CF80101.0
3
BF-DM-C-DP E162&E163-EN November 2022
DEALER MANUAL FOR DISPLAY
7.3 PRODUCT DESCRIPTION
7.3.1 Specifications
• Operating temperature: -20℃~45℃
• Storage temperature: -20℃~60℃
• Waterproof: IP65
• Storage room Humidity: 30%-70% RH
7.3.2 Functional Overview
• Battery capacity indication
• Support level indication
• Real-time speed indication
• Headlight control and indication
• Error code indication
• Automatic light sensitivity function
• Bluetooth function (only in DP E163.CAN)
7.4 DISPLAY INSTALLATION
7.4.1 Installation Position
Top tube is disconnected from down tube:
Top tube is connected to down tube:
7.4.2 Installation Steps
Place the display into the tube from the up-
per mounting hole, then tighten the M4*12
screws from the bottom mounting holes.
HMI can be mounted on
the front of top tube
If HMI is mounted on the
front of top tube, it is hard
to fix the screws.
Recommended
installation
position
4BF-DM-C-DP E162&E163-EN November 2022
1
2
3
45
Power On/Off
7.5 DISPLAY
1Battery capacity indicator
2Speed indicator
3Support level indicator
4Headlight indicator
5Bluetooth indicator
7.6 KEY DEFINITION
5
BF-DM-C-DP E162&E163-EN November 2022
DEALER MANUAL FOR DISPLAY
7.7 NORMAL OPERATION
7.7.1 Power On/ Off
Press and hold (>2.5S) on the display to turn on the system.
Press and hold (>2.5S) again to turn off the system.
7.7.2 Support Level Selection
When the display is turned on, press the (<0.5S) button to switch to the support level, the lowest
level is 1, the highest level is 3. When the support level indicator doesn't light up, there is no power
assistance.
7.7.3 Headlight/ Backlight
Double click the button to turn on the headlight, and the display interface dims.
Double click the button again to turn off the headlight and the display interface lights up.
6BF-DM-C-DP E162&E163-EN November 2022
7.7.4 Battery Capacity Indication
The battery capacity is indicated with 5 levels. When the lowest level indicator flashes that means
battery needs to charge. The battery capacity is shown as follows:
Bars Capacity Range Example
5 bars 80%-100%
4 bars 60%-80%
3 bars 40%-60%
2 bars 20%-40%
1 bar 5%-20%
1 flashing <5%
7.7.5 Bluetooth Indication
Note: Only DP E163.CAN is the Bluetooth version.
This display is equipped with OTA function, which can update firmware through the bluetooth.
This display can be connected to the Bafang Go APP through Bluetooth. The customer also can
develop their own app based on the SDK provided by BAFANG.
The data that can be sent to APP are as follow:
No. Function No. Function
1 Speed 8 Range
2 Support level 9 Heart beat
3 Battery 10 Calories
4 Current 11 Sensor signal
5 Headlight state 12 Battery Info.
6 Trip 13 Ststem Info.
7 ODO 14 Error code
7
BF-DM-C-DP E162&E163-EN November 2022
DEALER MANUAL FOR DISPLAY
7.8 ERROR CODE DEFINITION
The ebike system's parts are automatically monitored in real time. If a part is abnormal, the corresponding error code
is displayed on the HMI. The E162.CAN/ E163.CAN flashes the code at a frequency of 1 Hz.
The troubleshooting methods in the list are listed in order according to the fault probability and the
operability of the related parts. In practice, dealers can adjust the order based on the existing tools and
spare parts. (For detailed disassembly steps, please refer to the dealer manual of the corresponding
parts on the official website. <www.bafang-e.com>)
In order to protect the electric parts, before disassembling the parts, please switch off the system power first by pressing the
control unit of HMI and then disconnect the power cable of the disassembled part. When installing the parts, please fix the
parts first, then connect the power cable of the parts, and finnally switch on the system power by pressing the control unit
of HMI.
Please contact Bafang after-sale service personnel <[email protected]> if the above troubleshooting fails to solve the
problem or the error code is not in the above list.
Code Cause Troubleshooting
Hub Motor System Mid Motor System
Throttle not in place
1. Check whether the throttle is in place.
2. Check whether the throttle cable is con-
nected correctly or the cable (from throttle
to controller) is damaged.
3. Troubleshoot the faulty part:
1) Replace the throttle
2) Replace the controller
1. Check whether the throttle is in place.
2. Check whether the throttle cable is
connected correctly or the cable (from
throttle to drive unit) is damaged.
3. Troubleshoot the faulty part:
1) Replace the throttle
2) Replace the drive unit
System overvoltage
protection
1. Check whether the nominal voltage
of the battery is the same as the con-
troller.
2. Troubleshoot the faulty part:
1) Replace the battery
2) Replace the controller
1. Check whether the nominal volt-
age of the battery is the same as the
drive unit.
2. Troubleshoot the faulty part:
1) Replace the battery
2) Replace the drive unit
Hall signal in motor is
abnormal
1. Check whether the motor cable is
connected correctly or the cable (from
motor to controller) is damaged.
2. Troubleshoot the faulty part:
1) Replace the motor
2) Replace the controller
Replace the drive unit
8BF-DM-C-DP E162&E163-EN November 2022
Code Cause Troubleshooting
Hub Motor System Mid Motor System
Phase wire in motor abnormal
1. Check whether the motor cable is
connected correctly or the cable (from
motor to controller) is damaged.
2. Troubleshoot the faulty part:
1) Replace the motor
2) Replace the controller
Replace the drive unit
Motor overtemperature
protection
(Only occur when the
motor is equipped with the
temperature sensor.)
1. If riding for a long time, turn off the
system and let the motor cool down.
2. If no ride or riding for a short time,
troubleshoot the faulty part:
1) Replace the motor
2) Replace the controller
1. If riding for a long time, turn off
the system and let the drive unit
cool down.
2. If no ride or riding for a short
time, replace the drive unit.
Motor temperature sensor
abnormal
(Only occur when the
motor is equipped with the
temperature sensor.)
1. Check whether the motor cable is
connected correctly or the cable (from
motor to controller) is damaged.
2. Troubleshoot the faulty part:
1) Replace the motor
2) Replace the controller
Replace the drive unit
Controller curent sensor
abnormal
Replace the controller Replace the drive unit
Controller overtemperature
protection
1. If riding for a long time, turn off
the system and let the controller cool
down.
2. If no ride or riding for a short time,
replace the controller.
1. If riding for a long time, turn off
the system and let the drive unit cool
down.
2. If no ride or riding for a short time,
replace the drive unit.
Controller temperature sensor
abnormal
Replace the controller Replace the drive unit
9
BF-DM-C-DP E162&E163-EN November 2022
DEALER MANUAL FOR DISPLAY
Code Cause Troubleshooting
Hub Motor System Mid Motor System
Speed sensor abnormal
1. Check whether the motor cable is
connected correctly or the cable (from
motor to controller) is damaged.
2. Troubleshoot the faulty part:
1) Replace the motor
2) Replace the controller
1. Check whether the spoke magnet
has fallen off or the clearance
between the spoke magnet and the
speed sensor is within the normal
range (10-15mm).
2. Check whether the speed sensor
cable is connected correctly or the
cable (from sensor to drive unit) is
damaged.
3. Troubleshoot the faulty part:
1) Replace the speed sensor
2) Replace the drive unit
Torque sensor abnormal
(Only occur when the drive
system is equipped with the
torque sensor.)
1. Check whether the torque sensor
cable is connected correctly or the
cable (from sensor to controller) is
damaged.
2. Troubleshoot the faulty part:
1) Replace the torque sensor
2) Replace the controller
Replace the drive unit
Communication abnormal
1. Check whether the HMI cable is
connected correctly or the cable (from
HMI to controller) is damaged.
2. Troubleshoot the faulty part:
1) Replace the controller if the HMI
turns off automatically after appear-
ing error code for 20 seconds.
2) Replace the HMI if the HMI
doesn't turn off automatically after
appearing error code for 20 seconds.
(move to the next page)
1. Check whether the HMI cable is
connected correctly or the cable (from
HMI to drive unit) is damaged.
2. Troubleshoot the faulty part:
1) Replace the drive unit if the HMI
turns off automatically after appear-
ing error code for 20 seconds.
2) Replace the HMI if the HMI
doesn't turn off automatically after
appearing error code for 20 seconds.
(move to the next page)
10 BF-DM-C-DP E162&E163-EN November 2022
Code Cause Troubleshooting
Hub Motor System Mid Motor System
Communication abnormal
3) If the BESST tool is available, con-
nect it with HMI and controller, read
the information of HMI and controller
and replace the part that cannot read
information.
3) If the BESST tool is available,
connect it with HMI and drive unit,
read the information of HMI and drive
unit and replace the part that cannot
read information.
ON/OFF Button detection
circuit abnormal
(Only occur when the drive
system is equipped with
Bafang CAN communication
protocol.)
1. If keep pressing the ON/OFF
button when the HMI powers on, the
error code will alarm. Release the
button and observe whether the code
disappears.
2. Troubleshoot the faulty part:
1) Replace the HMI
2) Replace the controller
1. If keep pressing the ON/OFF
button when the HMI powers on, the
error code will alarm. Release the
button and observe whether the code
disappears.
2. Troubleshoot the faulty part:
1) Replace the HMI
2) Replace the drive unit
WDT (Watch Dog Timer) in
controller is abnormal
Replace the controller Replace the drive unit
Discharge voltage of
battery pack is too low
1. Charge the battery
2. Replace the battery
Discharge voltage of single
cell is too low
1. Charge the battery
2. Replace the battery
c Voltage difference between
single cell
Replace the battery
The battery error codes of 42, 49, 4C only occur when the drive system is equipped with the smart BMS and Bafang CAN
communication protocol.
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali BAFANG Apparecchiature di registrazione
Manuali Apparecchiature di registrazione popolari di altre marche
Strymon
Strymon NIGHTSKY Manuale utente
Mitsubishi Electric
Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Manuale utente
Tews Technologies
Tews Technologies TPMC465 Manuale utente
Honeywell
Honeywell Excel 50 Manuale utente
SeaLevel
SeaLevel COMM+8.LPCI Manuale utente
Arturia
Arturia AUDIOFUSE STUDIO Manuale utente
