Baha Auto-Lock Arm Awning Manuale di istruzioni
!
!
!
!
!
!
!
!
Installing)Auto-Lock)Arm)Awning)
!
"#$%!&'$()*+,#!
--$.$#+/.!0*+.1!
-02/()$#,!3!4(2$5,!
!
677*,!8$9:+2$1!
-&721*$,,!;2+**!<5+#'!=/%%$2!
(/>/?+*+#@!+A!%/,7.2@!5/**B!
-CD!E'+**+>,!=$/1!12+**!?+#F!!
-G$#/*!6/>$!G$/,:2$!
-E$.(+*!
!
Fixing)Type)
!
H+?27!
6+%?$2!
&7.(2$#$I!02+()!72!4#7.$!
-J,$!#'$!>27K+1$1!
,(2$5,!
!
-J,$!#'$!>27K+1$1!
,(2$5,!!
!
-J,$!#'$!>27K+1$1!
,(2$5,!!
-LM%%!N2$$.!O/**!
E*:P,!
-QFL%%!G/,7.2@!
;2+**!0+#!
-=/%%$2!
<6'$,$!+#$%,!.$$1!#7!?$!
>:2('/,$1!,$>/2/#$*@B!!
!
!
!
Start by using your
template on the left
side of your window
to mark the holes of
your hood and side
arms. Once you
have marked the
holes, pre drill them
and insert the wall
plugs.
Now insert the top
hood tab screw, but
do not fully tighten
the screw and hang
the awning on this
screw. This will allow
you to then mark
the opposite hood
tab holes. Ensure
that your hood is
level by using a
spirit level prior to
marking out. Take
the hood down.
Take your template
and mark the
remaining screw
holes including your
side arms.
Pre- drill your holes,
ensuring that the
holes are deep
enough and insert
wall plugs provided.
Insert your top hood
screw and hang your
hood. Now insert
each of your four
hood screws. Finally
tighten each of the
four screws, to finish
mounting your
awning hood
!
!
Proceed to mount
the Side Rails to the
wall using the lower
pre drilled screw
holes
!
!
Mounting)the)Awning)
To mount your
Awning, insert the
"pin end" first and
drop the flat end
from the top of the
bracket.Take your
base rail arms and
attach them to the
base rail of your
awning. The screws
will already be
within the base rail.
Ensure that the arms
are facing up. Then
simply slide the base
rail arms up the side
arms.
!
!
!
R7:2!S5.+.P!+,!.75!>27A$,,+7./**@!+.,#/**$1!/.1!@7:!T:,#!,/K$1!7.!#'$!+.,#/**/#+7.!
$U>$.,$V!
0S=S!7AA$2!/!LW@$/2!5/22/.#@!7.!@7:2!.$5!?*+.1,F!E*$/,$!,$$!A:2#'$2!1$#/+*,!7.!7:2!
5$?>/P$F!
H72!A:2#'$2!+.A72%/#+7.!>*$/,$!(7.#/(#!7:2!(:,#7%$2!,$2K+($!#$/%!G7.1/@!#7!H2+1/@!
X/%!#7!L>%!!
E'7.$Y!Z[MM!M\X!Z]Z!72!^%/+*Y!,/*$,_?/'/F(7%F/:!!
!
Now pull the blind
down along the rails
and ensure side rails
are vertical. Place
the U-Brackets
approx 100mm from
the bottom of the
side rails and screw
into place on both
sides (you can raise
the blind again once
you have positioning
for the U- Brackets).
!
!
!
Indice
Altri manuali Baha Accessori
