Balanced Audio Technology VK-P5 Manuale utente

VK-P5

WARRANTY REGISTRATION FORM

Unit Serial Number: _______________________________________

Customer Name: _______________________________________

Address: _______________________________________

_______________________________________

Date of Purchase: _______________________________________

Purchased From:

Dealer Name: _______________________________________

Address: _______________________________________

_______________________________________

IMPORTANT NOTE:

In order to receive the full five year product warranty, please mail this

completed form together with a copy of your sales receipt to Balanced Audio

Technology at the address below, within thirty days of purchase.

Failure to do so will result in the product being warrantied for one year

from the date of manufacture.

1300 First State Blvd. Suite A Wilmington, DE 19804

Tel: 302-999-8855 Fax: 302-999-8818

VK-P5

Balanced Phono Stage

Owner's Manual

1300 First State Blvd. Suite A Wilmington, DE 19804

Tel: 302-999-8855 Fax: 302-999-8818

NOTE:

Your VK-P5 Phono Preamplifier was preset at the factory to the following

configuration:

Gain: High

Input Resistive Loading: 47kΩ

Input Capacitive Loading: None

Please refer to the chapter on configuration switch setting for information on

optimizing the unit parameters.

Introduction

Thank you for your purchase of the Balanced Audio Technology VK-P5 balanced phono

stage. Please read this owner's manual to obtain the full benefit of the VK-P5 in your system. It

will provide you with the needed safety information and operating procedures for this exceptional

unit.

WARNINGS

To prevent the possibility of serious injury, electrical shock or fire:

DO NOT operate with the cover removed.

DO NOT expose to rain or moisture.

DO NOT defeat the ground power-plug.

DO NOT replace fuse with anything other than the same type and rating as supplied by the factory.

Package Contents

Included in the box should be the following:

Description Quantity

VK-P5 Balanced Phono Stage 1

Power Cord 1

Male Connector Pins 10

Spare 6922 tube 1

Spare Fuse (See Fuse Protection) 1

Torx Wrench (T-10) 1

Spare Top Cover Screws 5

User’s Manual 1

Optional Accessories (as ordered)

Save all the packaging material in a safe dry area for the unlikely event that you need

to return the VK-P5 to the factory for service.

Reseating Tubes

Normally, reseating tubes upon delivery is not required. However, if any tubes have

noticeably drifted out of position due to unusually high transportation stress, it will be

advisable to reseat the tubes. Use the supplied Torx wrench to remove the top cover.

Reseat the tubes in their sockets and reinstall the top cover.

NOTE: When using the Torx wrench, make sure it is fully inserted so that the screw head is

not stripped.

Physical Placement

It is recommended that you provide for at least 6" of free space around the unit for proper

ventilation.

Mount the unit on a hard surface with proper ventilation underneath.

Do not stack the VK-P5 phono stage on top of other units, nor vice versa.

General Description of VK-P5 Phono Preamplifier

The VK-P5 balanced all-tube phono stage is designed to provide the maximum possible

performance while operating in conjunction with the wide verity of phono cartridges available

today. The unit offers high degree of versatility in system configuration by providing the

following features:

- User-selectable gains of 50dB and 56dB

- Selectable cartridge loading for both resistance and capacitance

Please refer to the Configuration Switches section of this manual for information on how to

configure the VK-P5 phono stage for optimal performance in your system.

Connecting the VK-P5 to Your System

Cartridge Input

The back panel of the VK-P5 phono stage is equipped with one set of RCA cartridge input

connectors.

Output Connection

The VK-P5 is equipped with XLR output connectors. Any high quality set of balanced

interconnects can be used to connect the VK-P5 to your balanced preamplifier.

Single-ended preamplifiers can be connected to the VK-P5 output through the use of XLR-

to-RCA adapters, available from BAT.

Description of Controls

Power Switch

The power switch has two positions: OFF and ON. Putting the switch in the OFF position

(even for a short period of time) will reset the soft start and mute circuits. The VK-P5 will

then require about 45 seconds to return back to normal operation.

When you turn the unit ON, the VK-P5 will automatically go through a gentle power-on

sequence. At the end of this sequence the unit will automatically unmute. However, since the

source volume may be unknown at this time, it is advisable to turn the volume control on your

preamplifier fully counterclockwise and place the mute switch in "Mute" position before

turning the VK-P5 ON.

Output Muting

The output of the VK-P5 phono stage has a mute relay that disables it for about 45 seconds

every time the unit is turned ON.

When the unit is powered up it automatically self-mutes until the proper operating points of

the circuitry are reached. It will then go into normal play mode.

Changing the power switch position from ON to OFF even for short time, will make the unit

reset its power sequencing circuit and mute its output. It will then require about 45 seconds

for the unit to become operational again.

Configuration Switches

WARNINGS:

Please make sure that the VK-P5 is turned OFF and your preamplifier is in MUTE

before changing the state of any internal configuration switches in VK-P5.

Hazardous voltages are present on the unit’s printed circuit board. DO NOT operate

the VK-P5 with its top cover removed.

This section describes the setting of internal configuration switches that are located inside the

VK-P5 phono preamplifier. In order to access these switches, do the following:

1. Turn the VK-P5 OFF and disconnect the power cord from the power line

receptacle.

2. Remove the top cover, using the supplied Torx T-10 wrench.

Figure 1 depicts the locations of the VK-P5 internal configuration switches. These include:

1. Left and right channel cartridge loading switches S101 and S201

2. Gain switch S2

3. Gain potentiometers R130 and R230

The following section describes the operation of these controls.

Cartridge loading switches S101 and S201

Resistance:

The 47K load resistor is permanently connected to the cartridge input. If a different loading

value is desired, it can be obtained by switching in additional resistors, installed on the

VK-P5 PC board. This is accomplished by using the two DIP switches, S101 and S201,

which allow multiple choices for resistive and capacitive cartridge loading. Four positions are

reserved for the choice of resistance and four for capacitance. Out of each group of four, one

position is loaded with female pins and allows the user to install any desired value component

(this position is marked “USER”). Gold-plated solderable pins are supplied with the VK-P5

accessory kit, that should be attached to either resistors or capacitors supplied by the user.

This allows for easy installation and upgrade of user-supplied components.

The following resistors can be added in parallel with the 47K load:

Switch position Resistor Value

1 100 Ohm

2 1K

3 10K

4 User-Defined

Any parallel combination of the these values is also allowable.

Capacitance:

Various values of capacitors can be connected in parallel to the input via switches S101 and

S201. With these switches in the OFF position, there is no capacitive loading to the cartridge.

The capacitance choices include:

Switch Position Capacitor Value

5 100pF

6 470pF

7 1000pF

8 User-Defined

Any possible parallel combination of these values is also allowable.

Gain Switch

By moving the switch S2 from High to Low position, the amplifier’s gain is reduced by about

6dB. While the High gain position provides the most universal setting, it may be desired to

reduce the overall system gain when using some high output phono cartridges.

Gain Potentiometers

Gain potentiometers R130 and R230 allow the user to optimize the VK-P5 performance when

using very high output cartridges. It is recommended that for the cartridges with a nominal

output of 3mV or lower these controls be set fully clockwise.

Some high output cartridges (those with nominal output of over 3mV) may benefit from a

reduction in overall gain of the VK-P5 preamplifier and a corresponding increase in its input

overload margin. Moving the R130 and R230 controls fully counterclockwise will reduce the

overall preamplifier gain by approximately 6dB and increase the overload margin.

The fully clockwise position provides the most universal setting and is recommended for most

cartridges.

Balance Adjustment: The R130 and R230 controls can also be used to compensate for

system balance shift, such as when using cartridges exhibiting output voltage differences

between the left and right channels.

Indice

Altri manuali Balanced Audio Technology Amplificatore

Balanced Audio Technology

Balanced Audio Technology VK-3i Manuale utente

Balanced Audio Technology

Balanced Audio Technology REX II Manuale utente

Balanced Audio Technology

Balanced Audio Technology VK-150 Manuale utente

Balanced Audio Technology

Balanced Audio Technology VK-51SE Manuale utente

Balanced Audio Technology

Balanced Audio Technology VK-200 Manuale utente

Balanced Audio Technology

Balanced Audio Technology VK-31 Manuale utente

Balanced Audio Technology

Balanced Audio Technology REX Manuale utente

Balanced Audio Technology

Balanced Audio Technology VK-220 Manuale utente

Balanced Audio Technology

Balanced Audio Technology REX II Manuale utente

Balanced Audio Technology

Balanced Audio Technology VK-300x Special Edition Manuale utente

Balanced Audio Technology

Balanced Audio Technology VK-42SE Manuale utente

Balanced Audio Technology

Balanced Audio Technology VK-5i Manuale utente

Balanced Audio Technology

Balanced Audio Technology VK-250M Manuale utente

Balanced Audio Technology

Balanced Audio Technology Phono Module Manuale utente

Balanced Audio Technology

Balanced Audio Technology VK-75 Manuale utente

Balanced Audio Technology

Balanced Audio Technology VK-40 Manuale utente

Balanced Audio Technology

Balanced Audio Technology VK-250 Manuale utente

Balanced Audio Technology

Balanced Audio Technology VK-P10 Manuale utente

Balanced Audio Technology

Balanced Audio Technology VK-3 Manuale utente

Balanced Audio Technology

Balanced Audio Technology VK-5 Manuale utente

Balanced Audio Technology

Balanced Audio Technology VK-6200 Manuale utente

Balanced Audio Technology

Balanced Audio Technology VK-50SE Manuale utente

Balanced Audio Technology

Balanced Audio Technology VK-1000 Manuale utente

Balanced Audio Technology

Balanced Audio Technology VK-75SE Manuale utente

Manuali Amplificatore popolari di altre marche

ASTRO

ASTRO HVO V40 P Manuale utente

Marantz

Marantz SUPERSCOPE BLA-545 Istruzioni per il montaggio

NAD

NAD CI980 Manuale utente

Technics

Technics SE-CH770 Manuale utente

Harman Kardon

Harman Kardon HK6300 Manuale utente

NAD

NAD T975 Manuale utente

McIntosh

McIntosh MA6850 Manuale utente

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manuale utente

Viatron

Viatron Autrix Manuale utente

GME

GME GA9800 Manuale utente

Atlas

Atlas CP700 Manuale utente

Roland

Roland KC-1000 Manuale utente

Pyle

Pyle PFMRA350BW Manuale utente

Advantage

Advantage S-250 Manuale utente

IRT Electronics

IRT Electronics DVA-3007 Manuale utente

Dimavery

Dimavery BA-100 Series Manuale utente

Sony

Sony XM-S400D Manuale utente

Schertler

Schertler ROY X Manuale utente