Baltech ACCESS200 Manuale utente
BALTECH AG
Lilienthalstrasse 27
85399 Hallbergmoos
Germany
Phone: +49 (811) 99 88 1-0
Fax: +49 (811) 99 88 1-11
Mail: [email protected]
Website: www.baltech.de
v1.1
p 1/2
ACCESS200 installation guide
1. Install readers
Fix the base part to a single gang box or directly to the mounting surface.
Use 3 mm diameter countersunk head screws. Heads must not stand out
more than 1
mm from the base surface.
•
When using stranded wires, make sure there are no wires outside the
cages of the pluggable cage clamp.
•
To avoid rain interference, mount outdoor keypad readers upright or
at a protected spot. Otherwise, ensure large water drops are
wiped off
if readers are malfunctioning.
Connector and pins
(reader rear view)
Pigtail cable connection / Molex Pico-SPOX (outdoor/potted
versions) stranded, AWG28, power Red&Black AWG 24
Color
Connector pin #
Signal/funct.
White/Orange
1
WIE_D0/RS485A
Orange
2
WIE_D1/RS485B
White/Green
3
LEDGN
Green
4
LEDRD
Red/White
5
USB Data -
Black/White
6
USB Data +
Red
7
+VIN
Black
8
GND
White/Blue
9
GND
Blue
10
REL_WC
White/Brown
11
REL_NO
Brown
12
REL_NC
J8 Pluggable cage clamp
(indoor versions)
Pin #
Signal/funct.
J8-1
GND
J8-2
+Vin
J8-3
WIE_D0/RS485A
J8-4
WIE_D1/RS485B
J8-5
LEDGN
J8-6
LEDRD
J8-7
REL_WC
J8-8
REL_NO
J8-9
REL_NC
2. Optional: Set bus address
When using a bus protocol (e.g. OSDP), set a bus address for each reader: Place a BALTECH AdrCard
in front of the reader and wait for the signal indicating the desired address.
If readers are already configured, the reader housing (i.e. the tamper switch) must be open.
Learn more:
docs.baltech.de/bus
-address
BALTECH AG
Lilienthalstrasse 27
85399 Hallbergmoos
Germany
Phone: +49 (811) 99 88 1-0
Fax: +49 (811) 99 88 1-11
Mail: [email protected]
Website: www.baltech.de
v1.1
p 2/2
3. Optional: Deploy Prox license
To deploy a Prox license for HID Prox, Indala, or Keri card support, present a BALTECH LicenseCard
to each reader. Successful deployment is signaled by a yellow and green LED sequence.
Learn more:
docs.baltech.de/
licensecard
4. Optional: Test reader functionality
By default, the readers will now read any card’s UID (serial number) and transmit it to the host
system. You can make use of this behavior to check if the readers are up and running: Use a test
card and configure the host system temporarily to accept this card’s UID.
5. Deploy configuration
BEC2 file
Deploy via the software tool “Uploader” (part of BALTECH ToolSuite).
Option
How it works
Requirements
Wired
upload
Connect the reader to your
laptop via USB or RS-232.
•Any ToolSuite version
Wireless
upload
- Beta -
Connect a transfer reader to
your laptop to upload the
configuration wirelessly via
NFC to the target reader.
•ToolSuite: v.4.26.00 or above
•Target reader: firmware 1100 v.2.00.00 or above
•Transfer reader:
•ID-engine ZB Brick, ISO product line (10115).
LEGIC readers (10117) will not work!
Position the transfer reader on top of the target
reader and align antenna centers (i.e., card
symbols on front stickers). Tolerance is 10 mm
max. in each direction.
Create
ConfigCard
- Beta -
Load configuration onto a
ConfigCard. When created,
present the card to each
reader. Successful
deployment is signaled by
yellow and green LED
sequence.
•ToolSuite: v.4.26.00 or above
•Reader to write config to card:
ID-engine ZB Brick, firmware 11.23.01 or above
•ConfigCard: BALTECH ConfigCard v2 or blank
MIFARE DESFire card (EV1 or above)
•Target reader: firmware 1100 v.2.00.00 or above
BEC file
Deploy via wired upload only. See description in table above.
ConfigCard
Present the ConfigCard to each reader. Successful deployment is signaled by a yellow and green
LED sequence.
Learn more:
docs.baltech.de
/deploy
Beta options are not yet included in the online documentation.
6. Test configuration
Test the configured readers with a project card. The host system must be configured for live
operations.
Support
Altri manuali Baltech Controllori di accesso IP
