Bamo MAGTOP 801 Manuale utente
LE EL INDICATORS
LE EL INDICATORS
MAGTOP 801, 803, 806
19-03-2014 560 M0 06 C
MES
560-06/1
WARNING
Level indicator installation and using must be done outside from any magnetic field zone. Use non magnetic connection (Brass, Stainless
Steel or plastic). Any iron device must be installed at 10 cm minimum distance fare. Ensure chemical compliance between liquid and
level indicator. To get easy mounting and dismounting, a valve can be placed between tank and level indicator flange. Those valves may
be used, also, for liquid regulation to avoid strong float up movement (which may damage it). Inlet tank pressure, then in level indicator,
must not be over specified in technical features (6 bar as a maximum).
INTRODUCTION
Those level indicators allow instantaneous liquid level reading, even they are opaque.They are installed on tank side, by flanges.
Measurement on communicating vessels principle. The Float, equipped with magnet, moves bi-colours flaps which keep their positions
until the float is coming back. Their colours (red and yellow on black back side) ensure instantaneous and easy reading. Equipped with
graduated rule (in option) reading accuracy will be higher.
INSTRUCTIONS MANUAL
Level indicators
MAGTOP
801, 803, 806
560 M1 06 C 19-03-2014 Page 2
1. MOUNTING
Verify tank flanges compatibility with MAGT P flanges.
Install level indicator on tank side.
Do not forget to set seals (not furnished).
It is highly suggested to set insulation valves, between tank and level indicator, in
order to be able to remove the float in case of jamming.
Insert the float by removing union 7.
H is indicating float top.
During installation, bi-colours flaps may not be goodly set.
They will get right position on float movement.
They must be red when float is going up, and yellow when float is going down.
In case of bad level reading, flaps rule can be turned around the tube by unlocking
fixing collars.
After re-positioning, lock smoothly collars to avoid damaging this rule.
MAGT P can be equipped with different options which are:
- Graduated ruler, done with agreement, with requested measure unit (cm, % or volume)
- Continuous level output rule with potentiometric or 4-20mA analogic output (RTM)
- Level switches: BRK-60 MAG ; BRT-60 MAG
(To set a level switches or other options, see specific starting up notice.)
2. STARTING UP
It is suggested to install level indicator on atmospheric pressure, to avoid to quick
up float movement, which may damage it.
n magnet passage, flaps turn of 180° passing from yellow to red.
Exact level is indicting by flaps which turned only of 90°.
Indicator drain has to be done by unscrewing nut 9.
3. MAINTENANCE
For wast liquids with particles, float might be stopped. Drain level indicator and
tank to eliminate dusts. If the float is steal keep stopped, dismount the MAGT P
for full cleaning.
4. TECHNICAL FEATURES
MAGT P 801
Process connection: PVC flange,
ND 25 or ND 32 (PN 10)
Material: PVC
Max. temperature of fluid: 50°C
Pressure /MAGT P: 6 bar at 20°C as a maximum
Density: 1
MAGT P 803
Process connection: PPH flange,
ND 25 or DN 32 (PN 10)
Material: PPH
Max. temperature of fluid: 90°C
Pressure /MAGT P: 6 bar at 20°C as a maximum
Density: 1
MAGT P 806
Process connection: PPH steel reinforced flanges,
ND 25 or DN 32 (PN 10)
Material: PVDF
Max. temperature of fluid: 110°C
Pressure /MAGT P: 6 bar at 20°C as a maximum
Density: 1
It. Description
1PVC, PPh or PVDF
guiding tube Ø 63
2MAKR L N magnet ruler
3PVC, PPh or PVDF float
4Supplementary support
5PVC or PPH steel reinforced
flanges, ND 25 or ND 32
6PVC, PPh or PVDF
sealing surface
7Magnet ruler fixing collar,
stainless steel 304
8Union (3 pieces) for maintenance
9Drain tap
10 Draining valve (option)
11 Level switches (option)
Questo manuale è adatto per i seguenti modelli
2
Altri manuali Bamo Pannello touch
