Banda Audioparts DYNAMIC 2000.4 Manuale utente
A M P L I F I E R A N D P R O C E S S O R
P A T E N T R E Q U I R E D
> <U S E R M A N U A L
E N G L I S H
A M P L I F I E R A N D P R O C E S S O R
P A T E N T R E Q U I R E D
CONGRATULATIONS ON YOUR CHOICE!
You have just purchased an amplifier featuring the maximum innovation and
technology. We are committed to only providing you with quality products
and that assure the best performance of your sound.
All materials used in manufacturing the Banda Audioparts amplifiers have
been carefully chosen and inspected. To assure that all our products are
delivered with the highest quality standard, we conduct laboratory tests and
follow ABNT standards.
We kindly ask you to read all topics in the user's manual carefully, so you
know how to use it and its warranty period. Please remember: similar to
other warranty policies, and ours only covers workmanship defects that the
Technical Service report has confirmed.
> <F R O N T P A N E L
L5 = It displays that channel 5 Limiter is operating
L6 = It displays that channel 6 Limiter is operating
DY1 = It displays that channel 1 has reached the maximum
power set using the power output function
DY2 = It displays that channel 2 has reached the maximum
power set using the power output function
DY3 = It displays that channel 3 has reached the maximum
power set using the power output function
DY4 = It displays that channel 4 has reached the maximum
power set using the power output function
ST1-2 = It displays that channels 1 and 2 are in stereo
ST3-4 = It displays that channels 3 and 4are in stereo
BD1-2 = It displays that channels 1 and 2 are in bridge
BD3-4 = It displays that channels 3 and 4 are in bridge
ON = It displays that the amplifier is on
SHORT / LOW BATT = See page - Troubleshooting
P A T E N T R E Q U I R E D
> <I N P U T S A N D O U T P U T S
1 - Audio signal input - Left
2 - Audio signal input - Right
3 - Audio processor output #5
4 - Audio processor output #6
Outputs 5 and 6 can be set via the app
GND 12VDC
REM
P A T E N T R E Q U I R E D
> <TECHNICAL SPECIFICATIONS
Maximum Power 14.4V @ 1 ohm
Maximum Power 14.4V @ 2 ohms
Maximum Power 14.4V @ 4 ohms
Maximum Power 14.4V Bridge
Maximum Power 12.6V @ 1 ohm
Maximum Power 12,6v @ 2 ohms
Maximum Power 12,6v @ 4 ohms
Maximum Power 12,6v Bridge
Efficiency @ 8 ohms
Efficiency @ 4 ohms
Efficiency @ 2 ohms
Efficiency @ 1 ohm
Input Voltage
Input Impedance
THD+N
Input Sensitivity
Signal-to-Noise Ratio
Frequency Response (OFF Switch)
Frequency Response
Bass Boost @ 45Hz
HPF (Subsonic)
LPF (Crossover)
Recommended Fuse
Quiescent Current
Maximum Current (sinusoidal signal)
Maximum Current (musical signal)
Power Supply Cables (min. recommended)
Output Cables (min. recommended)
-
4 x 600 Wrms
4 x 400 Wrms
2 x 1250 Wrms 4 ohms
-
4 x 500 Wrms
4 x 300 Wrms
2 x 1000 Wrms 4 ohms
-
84%
76%
-
9 - 15V
100K ohms
0.10%
220mV - 4V
80dB
-
5 a 22kHz (-3dBs)
-
-
-
100A
1A
240A
100A
21mm / 4 AWG
2 x 2.5mm / 2 x 13 AWG
Parameter DYNAMIC 2000.4 @ 2 ohms
P A T E N T R E Q U I R E D
DYNAMIC | dimensions |
Weight 3.3 Kg
Depth 64mm
Height 226mm
Width 235mm
> <TECHNICAL SPECIFICATIONS
P A T E N T R E Q U I R E D
>B L U E T O O T H C O N N E C T I O N
F O R S E T - U P <
Using a didactic and intuitive interface, it is possible to make all settings to
the Banda DYNAMIC 2000.4 internal processor via smartphone or tablet, thus
making the system alignment easier, which can be done in front of the system
and in real-time.
The app can be downloaded free from Google Play Store or Apple Store.•
I N T U I T I V E A P P Available for iOS and Android
• Download the app from Google Play Store or Apple Store (DYNAMIC Power)
Activate the device location•
Activate the Bluetooth connection•
Open the app•
The app automatically recognizes the processor•
Select the processor•
PAIRING
M O D O D E M O S C A N H E L P S U P O R T S A L E S
>A M P 2 0 0 0 . 4 X A i R D C : 0 D : 3 0 : 0 3 : D B : 9 E
>C O N N E C T I N G <
S T A N D B Y
P O W E R L I N E 1 . 4 E X I T
• Enter the password (default password = 0000)
To change the default password, enter a new password, and click OK•
If you want to change the password again, you must reset the processor•
M O D O D E M O S C A N H E L P S U P O R T S A L E S
>A M P 2 0 0 0 . 4 X A i R D C : 0 D : 3 0 : 0 3 : D B : 9 E
>E N T E R T H E P R O C E S S O R P A S S W O R D <
1 2 3 4
Save Password
CA NC EL OK
P O W E R L I N E 1 . 4 E X I T
P A T E N T R E Q U I R E D
> <W I R I N G E X A M P L E
DYNAMIC 2000.4 @ 2 ohms
| channel / 4 ohms bridge |
2 loudspeakers 250 Wrms @ 4 ohms
each connected in parallel, resulting
in 500 Wrms @ 2 ohms for channel
Channels 1 and 2
4ohm single-coil subwoofer or
woofer, resulting in 1000 Wrms
@ 4 ohms for bridge
Bridge channels 3 and 4
4-ohm single coil 1000 Wrms subwoofer or woofer,
resulting in 1000 Wrms @ 4 ohms per bridge
Bridge channels 1 and 2
NOTE: These diagrams are basic ones and are only intended as an example. This device
works with several systems, provided that the minimum impedance is observed.
P A T E N T R E Q U I R E D
> <T R O U B L E S H O T T I N G
Blue and Red LEDs are on
Protection System
The amplifier
temperature has reached
its operation limit
(approximately 85°C on
the external area)
Problem
Install the device in a well-
ventilated place and check
if the ventilation system is
not clogged. The amplifier
resumes operating
normally as soon as the
temperature goes down
Solution
Blue LED on, and Red LED
flashing with no audio
at the output
Short-circuit at the
audio output or
loudspeaker impedance
below the rated
amplifier impedance
Check if the loudspeaker
connecting cables are not
short-circuited, and if there
is no shorted loudspeaker
connected to the system, or
if the loudspeaker
impedance is not lower than
the minimum amplifier
impedance
Blue LED on, and Red LED
flashing according
to the music
Clipping LED displaying
that the output
distortion exceeds 1%
The system may work with
the amplifier featuring a
flashing Clipping LED;
however, the loudspeakers
connected to the output
feature an overheated coil
due to the Clip distortion
P A T E N T R E Q U I R E D
Yellow LED flashing Amplifier input voltage
below 9V
Check the battery load to
which the amplifier has
been connected. Also, bad
contact in the power supply
cables may result in voltage
drops. Check the voltage at
the amplifier input and
battery output to confirm if
the voltage drop is not
occurring at cables or
connections
Both Red and
Yellow LEDs on
Problem with the
amplifier
Please send it to our
nearest technical service
> <T R O U B L E S H O T T I N G
Problem Solution
P A T E N T R E Q U I R E D
Protection System
Indice
Altri manuali Banda Audioparts Amplificatore
