Bandwidth Audio Aurora One Manuale utente
Aurora One Rev 1.0 2
WARNING
FAILURE TO READ OWNER’S MANUAL BEFORE FIRST USE CAN
VOID YOUR WARRANTY
CONTAINS LETHAL VOLTAGES
High voltage can be lethal. Do not remove cover while preamplifier is connected to the
Mains power source. For service, contact Bandwidth Audio.
HIGH VACUUM TUBE TEMPERATURES
Vacuum tubes can get extremely hot with bulb temperatures capable of reaching 200ºC. Do
not touch or attempt to remove the tubes while they are hot.
DO NOT ENCLOSE
This preamplifier will get warm from use. Make sure to place the equipment in a non-
enclosed area with good ventilation and air flow.
Aurora One Rev 1.0 3
1.0 Aurora One Connections and Setup ............................................................................................. 4
1.1 Preamplifier Placement ..................................................................................................................................... 4
1.2Mains AC Grounding.......................................................................................................................................... 4
1.3 Powering ON & OFF .......................................................................................................................................... 5
1.4 Input Connections ............................................................................................................................................... 5
1.5 Output Connections ........................................................................................................................................... 5
2.0 Gain Selection ......................................................................................................................................... 6
2.1 Manual Controlled Gain ................................................................................................................................... 7
2.2 Pre-Programmed Gain.................................................................................................................................... 10
2.1.1. Setting the DIP Switches .................................................................................................................................................................................................11
2.1.2 Gain Setting Examples ......................................................................................................................................................................................................13
3.0 Controls and Layout.......................................................................................................................... 14
3.1 Front Features..................................................................................................................................................... 14
3.2 Back Features ...................................................................................................................................................... 16
4.0 Typical Specifications........................................................................................................................ 18
5.0 Notes:....................................................................................................................................................... 20
Figure 1: Positions of Gain and Bypass switches.................................................................................................... 8
Figure 2: DIP Switches for Pre-Programmed Gain Control.............................................................................. 11
Figure 3: Pre-Programmed Gain Example.............................................................................................................. 13
Aurora One Rev 1.0 4
1.0 Aurora One Connections and Setup
From the factory, the Aurora One is configured in High Gain Mode for all inputs, unless the
front gain and bypass toggle switches are used.
•To learn about selecting and programming the gain modes, see section 2.0
1.1 Preamplifier Placement
For best operation and longest life of components, the preamplifier should be set up and used in a
well-ventilated area with good air circulation. Do not use the amplifier in enclosed furniture as
overheating can damage the amplifier, diminish tube life, and cause risk of fire.
It is always recommended to place the preamplifier on a sturdy substantial shelf to help minimize
vibrations coupled in from the floor.
Radiating electromagnetic noise (EMI) from sources such as large transformers, cellphones and Wi-
Fi routers can also cause audible noise from the speakers if this equipment if placed too close to
the preamp. It is best to have this equipment located far away.
1.2 Mains AC Grounding
Always share the same AC mains ground circuit with all other audio equipment.
For lowest noise, it is always recommended to share the same AC mains ground circuit between all
audio equipment in a system. The easiest and best way to achieve this is to share a common outlet
or known common circuit and use a high-quality power strip to power all pieces of equipment. This
is most desirable to ensure the ground reference of all audio equipment is at the same potential.
Ground is used as a safety voltage reference and should not have any current flowing. However, it
is likely that any 2 ground circuits in a building’s wiring will have a small voltage differential
between them. If these grounds are shared by audio equipment, a ground loop is formed, and the
small voltage differential can now drive a current through the audio ground, causing noise.
Faulty equipment on the AC line can also be a source of ground noise.
Aurora One Rev 1.0 5
1.3 Powering ON & OFF
The Aurora One is designed with a time delay start sequence to ensure all operating voltages are
stabilized and the preamplifier is ready to play audio before the output is active. This removes the
chance of any pop and noise during power on and off. The Aurora One can be turned on and off
without any need for power sequencing with other equipment. The “Active” indicator on the front
panel shows the status of the power-on sequence. The preamp output will be active approximately
25 seconds after power-on.
The power on sequences is as follows:
The Aurora One “Power” indicator will illuminate. The “Input”, “Gain”, “Bypass” and “Mute”
settings will also illuminate with their status. After a delay of approximately 25 seconds, the
“Active” indicator will illuminate, indicating that the preamp is ready for use and music will
play.
1.4 Input Connections
Input connections are made by connecting analog audio sources to the Aurora One using
the RCA inputs on the back of the unit. Up to 6 stereo inputs can be connected at a time.
Input selection is made by using the rotary “Input” knob on the front of the unit. LEDs will
illuminate to show which input is selected.
1.5 Output Connections
The Aurora One is equipped with 2 pairs of stereo RCA outputs on the back of the unit.
Each output is independently buffered to prevent unwanted loading.
The signal on each output is identical which gives the ability to drive active subwoofers,
control zones in a house, or quickly change between 2 stereo setups. Each output can be
muted using the toggle switches on the front.
Aurora One Rev 1.0 6
2.0 Gain Selection
The Aurora One is designed with 3 gain level modes to improve volume level matching between
audio source. This reduces the need for constant volume control adjustments when changing the
input source.
The 3 Gain levels are:
•Bypass: 0dB
•Low Gain: 8dB
•High Gain: 14dB
Gain selection is controlled in two ways:
1. Manual Controlled Gain (Section 2.1)
Using the “Gain” and “Bypass” toggle switches located on the front to override the pre-
programmed gain.
When starting out, it is recommended to use the manual controlled gain (front toggle
switches) to help determine the best gain setting for each input connected. Once the
desired gain has been found, gain setting can be programmed using the DIP switches
located on the back of the unit. This, way the gain can now automatically be recalled as the
inputs are selected.
2. Pre-Programmed Gain (Section 2.2)
Using the DIP switches located on the back of the unit to program each input.
Aurora One Rev 1.0 7
2.1 Manual Controlled Gain
The Aurora One’s preamp gain can be manually selected using the “Gain” and “Bypass” toggle
switches located on the front of the unit. The “Gain” and “Bypass” switches each have 3 positions.
Gain Toggle Switch:
Down: Low Gain Mode (forced)
Middle: Pre-programmed control is selected
Up: High Gain Mode (forced)
Bypass Toggle Switch:
Down: Bypass Off (forced) - Gain mode always selected
Middle: Pre-programmed control is selected
Up: Bypass On (forced) - Bypass always on regardless of gain setting
Note: It is important to remember that the Bypass switch automatically takes priority over
the gain switches. With Bypass mode forced on, the gain selection is ignored. This is due to
the fact that Bypass mode has 0dB of gain. The gain selection is therefore irrelevant.
Aurora One Rev 1.0 8
* Bypass On takes priority, all gain selections are ignored
Bypass On:
When Bypass mode is ON, the LED next to the bypass switch will illuminate and the Aurora One
will enter Bypass mode with 0dB of gain.
Simultaneously, the High or Low Gain LED (whichever was selected) will turn off. This is to remind
the user that Bypass mode takes priority over the gain setting when Bypass is on.
The Aurora One
will never enter High or Low gain mode.
Bypass Off:
When Bypass mode is Off, High or Low Gain LED (whichever is selected) will illuminate.
The Aurora
One will never enter Bypass mode.
Pre-programmed
High Gain (forced)
Low Gain (forced)
Pre-programmed
Bypass On (forced)*
Bypass Off (forced)
Figure 1: Positions of Gain and Bypass switches
Aurora One Rev 1.0 9
Bypass Pre-programmed:
With the Bypass toggle switch in the middle position, Bypass mode will be determined by the Pre-
programmed setting located on the back of the unit.
High Gain:
When the Gain mode is set to “High Gain”, the “High Gain” LED will illuminate and the Aurora One
will have a gain of 14dB. This is only true if the Bypass toggle is forced Off or if the Bypass in the
pre-programmed setup is also off (bypass has priority).
Low Gain:
When the Gain mode is set to “Low Gain”, the “Low Gain” LED will illuminate and the Aurora One
will have a gain of 8dB. This is only true if the Bypass toggle is forced Off or if the Bypass in the
pre-programmed setup is also off. (remember bypass has priority).
.
Gain Pre-programmed:
With the Gain toggle switch in the middle position, the Gain will be determined by the Pre-
programmed setting located on the back of the unit.
Aurora One Rev 1.0 10
2.2 Pre-Programmed Gain
The Aurora One’s preamp gain can be pre-programmed for each audio input (1 through 6) using
the DIP switches located on the back of the unit. The gain setting is then automatically recalled
when the desired input is selected using the “Input” knob on the front.
Note: For the Pre-programmed settings to take effect, the “Gain” and “Bypass” toggle
switches must be in the middle positions (selecting pre-programmed control). Otherwise,
they will force the preamp into a different mode.
The goal is to set the gain for each input such that the volume difference between audio sources is
minimized when changing inputs. This will not only provide better matching between audio sources
with different signal levels, but also reduce the risk of destroying your speakers and your hearing
by selecting an undesired input.
Indice
Altri manuali Bandwidth Audio Amplificatore
