banks Derringer Manuale utente
Banks
Derringer®
Tuner
All Derringer Applications
THIS MANUAL IS FOR USE WITH SYSTEM P/N:
66575, 66545, 66577, 66547, 66571, 66541, 66572, 66582, 66552
Gale Banks Engineering
546 Duggan Avenue • Azusa, CA 91702
(626) 969-9600 • Fax (626) 334-1743
Product Information & Sales: (888) 635-4565
Customer Support: (888) 839-5600
Installation Support: (888) 839-2700
bankspower.com
8/06/2018 PN 97671 v.1.1
©2018 Gale Banks Engineering
Owner’sManual
with Installation Instructions
297671 v.1.1
General Installation Practice
Dear Customer,
If you have any questions
concerning the installation
of your Banks Techni-Cooler,
please call our Technical Ser-
vice Hotline at (888) 839-2700
between 7:00 am and 4:00 pm
(PT). If you have any questions
relating to shipping or billing,
please contact our Customer
Service Department at (888)
839-5600.
Thank you.
1. Before starting work, familiarize
yourself with the installation procedure
by reading all of the instructions.
2. The exploded views (Pages 8-11)
provides only general guidance. Refer
to each step and section diagram in
this manual for proper instruction.
3. Throughout this manual, the left
side of the vehicle refers to the driver’s
side, and the right side to the passen-
ger’s side.
4. Disconnect the negative (ground)
cable from the battery (or batteries, if
there are more than one) before begin-
ning work. The OEM battery clamp can
be removed using a 10mm socket or
wrench.
5. Route and tie wires and hoses a
minimum of 6" away from exhaust
heat, moving parts and sharp edges.
Clearance of 8" or more is recom-
mended where possible.
6. During installation, keep the work
area clean. Do not allow anything to
be dropped into intake, exhaust, or
lubrication system components while
performing the installation, as foreign
objects will cause immediate engine
damage upon start-up.
CAUTION! Do not use floor jacks
to support the vehicle while
working under it. Do not raise
the vehicle onto concrete blocks,
masonry or any other item not
intended specifically for this use.
7. During installation, keep the work
area clean. Do not allow anything to
be dropped into intake, exhaust, or
lubrication system components while
performing the installation, as foreign
objects will cause immediate engine
damage upon start-up.
TOOLS REQUIRED:
• Metric sockets and wrenches
• Diagonal (side cutter) Pliers
• Exacto knife or other
small bladed knife
• Drill motor*
• #31 (.1200 dia.) Drill bit*
• #1 or 7/32 (.228 dia.) Drill bit*
*Required only if mounting switch in dash
Highly recommended
tools and supplies:
• Standard and Phillips screwdrivers
• Silicon sealer (black or
clear recommended)
• Metal coat hanger
• Clip/Fastener Removal Tool
97671 v.1.1 3
THIS IS A HIGH PERFORMANCE
PRODUCT. USE AT YOUR OWN
RISK. Do not use this product
until you have carefully read
the following agreement.
This sets forth the terms and
conditions for the use of this
product. The installation of
this product indicates that the
BUYER has read and under-
stands this agreement and
accepts its terms and condi-
tions.
Disclaimer of Liability
Gale Banks Engineering Inc., and its
distributors, employees, and dealers
(hereafter “SELLER”) shall in no way
be responsible for the product’s proper
use and service. The BUYER hereby
waives all liability claims.
The BUYER acknowledges that he/ she
is not relying on the SELLER’s skill or
judgment to select or furnish goods
suitable for any particular purpose
and that there are no liabilities which
extended beyond the description on
the face hereof and the BUYER hereby
waives all remedies or liabilities,
expressed or implied, arising by law
or otherwise, (including without
any obligations of the SELLER with
respect to fitness, merchantability,
and consequential damages) whether
or not occasioned by the SELLER’s
negligence.
The BUYER is responsible to fully
understand the capability and
limitations of his/her vehicle according
to manufacturer specifications and
agrees to hold the SELLER harmless
from any damage resulting from the
failure to adhere to such specifications.
The SELLER disclaims any warranty
and expressly disclaims any liability
for personal injury or damages. The
BUYER acknowledges and agrees
that the disclaimer of any liability for
personal injury is a material term for
this agreement and the BUYER agrees
to indemnify the SELLER and to hold
the SELLER harmless from any claim
related to the item of the equipment
purchased. Under no circumstances
will the SELLER be liable for any
damages or expenses by reason of the
use or sale of any such equipment.
The BUYER is responsible to obey
all applicable federal, state, and
local laws, statutes, and ordinances
when operating his/her vehicle, and
the BUYER agrees to hold SELLER
harmless from any violation thereof.
The SELLER assumes no liability
regarding the improper installation
or misapplication of its products. It is
the installer’s responsibility to check
for proper installation and if in doubt,
contact the manufacturer.
The BUYER is solely responsible for all
warranty issues from the automotive
manufacturer.
Disclaimers
497671 v.1.1
Limitation of Warranty
Gale Banks Engineering Inc. (hereafter
“SELLER”), gives Limited Warranty as
to description, quality, merchantability,
fitness for any particular purpose,
productiveness, or any other matter of
SELLER’s product sold herewith. The
SELLER shall be in no way responsible
for the product’s open use and service
and the BUYER hereby waives all rights
except those expressly written herein.
This Warranty shall not be extended or
varied except by written instrument
signed by SELLER and BUYER. Please
see enclosed warranty information
card, or go to www.bankspower.com/
warranty, for warranty information
regarding your product. All products
that are in question of Warranty must be
returned shipping prepaid to the SELLER
and must be accompanied by a dated
proof of purchase receipt. All Warranty
claims are subject to approval by Gale
Banks Engineering Inc.
Under no circumstance shall the
SELLER be liable for any labor charged
or travel time incurred in diagnosis for
defects, removal, or reinstallation of
this product, or any other contingent
expense. Under no circumstances will
the SELLER be liable for any damage or
expenses incurred by reason of the use
or sale of any such equipment.
IN THE EVENT THAT THE BUYER
DOES NOT AGREE WITH THIS
AGREEMENT:
The BUYER may promptly return this
product, in a new and unused condition,
with a dated proof-of-purchase, to the
placeof-purchase within thirty (30) days
from date-of-purchase for a full refund,
less shipping and/or restocking fee.
The installation of this product
indicates that the BUYER has read
and understands this agreement and
accepts its terms and conditions.
Disclaimers, cont'd...
97671 v.1.1 5
Table of Contents
1. Installation of Wire Harness and Derringer Tuner ..............................7
1.1 Derringer Tuner System Configuration .........................................................8
1.1.1 Stand Alone/Switch Configuration .........................................................8
1.1.2 iDash 1.8 Configuration ........................................................................10
1.2 Derringer Sensor Harness Installation........................................................12
1.3 Derringer Tuner Installation ........................................................................14
1.4 Vehicle Specific Instructions.......................................................................21
1.4.1 2011-2016 F150 EcoBoost....................................................................22
1.4.2 2017-2018 GM 6.6 L5P..........................................................................24
1.4.3 2014-2017 EcoDiesel Ram/Jeep............................................................27
2. Derringer Tuner Operations ............................................................... 34
3. Troubleshooting.........................................................................................37
3.1 General troubleshooting info......................................................................38
3.2 2011-2016 F150 EcoBoost..........................................................................39
3.3 2017-2018 GM 6.6 L5P ...............................................................................40
3.4 2014-2017 EcoDiesel Ram/Jeep .................................................................42
4. Banks Power Decal ...................................................................................44
4.1 2011-2016 F150 EcoBoost..........................................................................45
4.2 2017-2018 GM 6.6 L5P................................................................................46
4.3 2014-2017 EcoDiesel Ram/Jeep .................................................................47
697671 v.1.1
This page is left blank purposely...
97671 v.1.1 7
SECTION 1
Installation of Wire Harness
and Derringer Tuner
897671 v.1.1
Bypass Plug
OR
Application
Specific Harness
PN:
*Varies based
on application
SECTION 1.1 DERRINGER TUNER SYSTEM CONFIGURATION
1.1.1: Stand Alone/Switch Config.
(Optional)
97671 v.1.1 9
(Ex: MAP, FRP, TIP, MAF,EGT..etc)
10 97671 v.1.1
Bypass Plug
OR
Application
Specific Harness
PN:
*Varies based
on application
(Optional)
SECTION 1.1 DERRINGER TUNER SYSTEM CONFIGURATION
1.1.2: iDash 1.8 Config.
Altri manuali per Derringer
1
Indice
Altri manuali banks Sintonizzatore
