Baoding Longer Precision Pump LEAD-2 Longer Manuale utente

LEAD-2 Longer Peristaltic Pump

Baoding Longer Precision Pump Co.,Ltd.

BaodingLongerPrecisionPumpCo.,Ltd

ADD: Building A,Chuangye Center Baoding

National High - Tech Industrial Development Zone

Baoding,Hebei,China 071051

TEL: 86 - 312 - 3110087 3138553

FAX: 86 - 312 - 3168553

E - mail: longer@longerpump.com

Www.longerpump.com

LEAD-2PERISTALTICPUMP

OPERATING MANUAL

TableofContents

IMPORTANT INFORMATION：

Please read operation manual carefully before operation.

WARNINGS：

Tubing breakage may result in fluid being sprayed from

pump. Use appropriate measures to protect operator and

equipment. Please check the tubing frequently and

changethetubingintime.

If the power line or the plug is worn or damaged please

pull out the plug (Hold the plug not the power line when

pulling out).

Please shut down the power supply and pull out the plug

when meet below circumstances (Hold the plug not the

power line when pulling out).

Thefluidssplashonthebodyofthepump.

You think the pump needs to be maintained or repaired.

Please shut down the power supply before install the

external control equipments.

LEAD-2OPERATINGMANUAL

Introduction

Operation Panel

Basic Operation

Running Interface

Menu Frame Work

Function Setting

Acceptable Pump Heads and Tubing

Pump Head Mounting

Tubing Loading

Remote Control Function

Optional Accessories

Maintenance

Warranty

Technical Specifications

Start/Stop Key

Direction Key

Adjusting Knob

Prime Key

Calibration

System Setting

Control Mode

Exit

TableofContents

IMPORTANT INFORMATION：

Please read operation manual carefully before operation.

WARNINGS：

Tubing breakage may result in fluid being sprayed from

pump. Use appropriate measures to protect operator and

equipment. Please check the tubing frequently and

changethetubingintime.

If the power line or the plug is worn or damaged please

pull out the plug (Hold the plug not the power line when

pulling out).

Please shut down the power supply and pull out the plug

when meet below circumstances (Hold the plug not the

power line when pulling out).

Thefluidssplashonthebodyofthepump.

You think the pump needs to be maintained or repaired.

Please shut down the power supply before install the

external control equipments.

LEAD-2OPERATINGMANUAL

Introduction

Operation Panel

Basic Operation

Running Interface

Menu Frame Work

Function Setting

Acceptable Pump Heads and Tubing

Pump Head Mounting

Tubing Loading

Remote Control Function

Optional Accessories

Maintenance

Warranty

Technical Specifications

Start/Stop Key

Direction Key

Adjusting Knob

Prime Key

Calibration

System Setting

Control Mode

Exit

Introduction

Lead-2 peristaltic pump is an accurate flow rate pump. Its acceptable

pump heads are 15-48, 15-88, 15-24 and 15-44. 2, 4 and 8 channels

are available. It offers flow rates of 0.001 300 mL/min. It has flow

rate and speed adjusting function. Lead-2 has other functions like

start/stop, cw/ccw, prime (fast filling and empting), flow rate

calibration, tubing selection, RS485 communication and remote

control, etc.

Operation Panel

LCD Screen

Prime Key

Direction Key

Start/Stop Key

Adjusting Knob

ID 0.5 INT

100.0 RPM

▲

LEAD-2OPERATINGMANUAL LEAD-2OPERATINGMANUAL

S Standard Configuration

S1 Pump Head

S2 Driv

PParts

P1 Power Switch

P2 Remote Control Interface

P3 Power Socket

Reference:

For detail information about external control function please see

page 13.

Basic Operation

Start/Stop Key

Pressthe tostartorstopthepump.

Direction Key

Press the to change the rotation direction of the

pump. This key is valid when the pump is running.

Adjusting Knob

Function 1: Adjust the flow rates or speed in running state.

Function 2: In menus selection state when the pump is idle, press

the for confirmation and turn the

for selecting and setting the menus.

Prime Key

In common state, press the to enter prime state when

the pump runs at full speed for empting, filling and rinsing

operation; Press the again to return to common state.

In prime state, other keys are invalid except .

Prime state interface is shown as below:

Start/Stop Key

direction key

adjusting knob adjusting

knob

Prime Key

Direction Key

Introduction

Lead-2 peristaltic pump is an accurate flow rate pump. Its acceptable

pump heads are 15-48, 15-88, 15-24 and 15-44. 2, 4 and 8 channels

are available. It offers flow rates of 0.001 300 mL/min. It has flow

rate and speed adjusting function. Lead-2 has other functions like

start/stop, cw/ccw, prime (fast filling and empting), flow rate

calibration, tubing selection, RS485 communication and remote

control, etc.

Operation Panel

LCD Screen

Prime Key

Direction Key

Start/Stop Key

Adjusting Knob

ID 0.5 INT

100.0 RPM

▲

LEAD-2OPERATINGMANUAL LEAD-2OPERATINGMANUAL

S Standard Configuration

S1 Pump Head

S2 Driv

PParts

P1 Power Switch

P2 Remote Control Interface

P3 Power Socket

Reference:

For detail information about external control function please see

page 13.

Basic Operation

Start/Stop Key

Pressthe tostartorstopthepump.

Direction Key

Press the to change the rotation direction of the

pump. This key is valid when the pump is running.

Adjusting Knob

Function 1: Adjust the flow rates or speed in running state.

Function 2: In menus selection state when the pump is idle, press

the for confirmation and turn the

for selecting and setting the menus.

Prime Key

In common state, press the to enter prime state when

the pump runs at full speed for empting, filling and rinsing

operation; Press the again to return to common state.

In prime state, other keys are invalid except .

Prime state interface is shown as below:

Start/Stop Key

direction key

adjusting knob adjusting

knob

Prime Key

Direction Key

ID 0.5 INT■

123.4mL/min

▲

Running Interface

Display running interface after initialization.

ID 0.5 INT■

90.5 rpm b.

Flow Rate Display Speed Display

Menu Frame Work

ID 0.5 INT■

123.4mL/min

Running interface

1.Calibration

2. ystem SettingS

3.Control mode

4. xitE

Act Vol 1234：μL

Press to exit

a.Tubing ID

0.5mm

：

b.Test time

0.5min

：

c.Remote

Control:on

d. ump I.D.#.P

e.Footswitch

Gated

f. ackB

Select

RPM Flow

Function Setting

ID 0.5 INT■

123.4mL/min

In running interface, press the to enter the

calibration interface. Turn the to select 4

function setting interfaces.

Adjusting Knob

Calibration Setting

Calibration is needed in below situations:

1.Use the pump the first time; 2. Change the pump head; 3.

Change the tubing; 4. Setting new flow rate; 5. Operating

condition changes.

ID 0.5 INT■

123.4mL/min Tes t ti me

0.5min

：

Cal Vol: 1234 μL

Press to begin

Enter calibration function setting interface:

Note:

In speed Display, the calibration function is forbidden. In Running

Interface, press the , it will display:Adjusting Knob

LEAD-2OPERATINGMANUAL LEAD-2OPERATINGMANUAL

1.Calibration 2. ystem SettingS

3.Control mode

4. xitE

1.Calibration

a. Running direction.

b. Current flow rate and speed.

c. Tubing inner diameter. “ID0.5” means the inner diameter of the

tubing is 0.5 mm.

d. Start/Stop state: “Start” state displays “ ”, “Stop” state

displays “ ”.

Control mode: “INT” means the pump is controlled by internal

control; “shut” means remote control is in “off” state; “V” means

the pump is controlled by remote control analog voltage signal;

“mA” means the pump is controlled by remote control analog

current signal.

■

Running interface

To switch to “Speed Display”

please see page 9 “Control

Mode” for setting method

Press

the Knob

Turn the

Knob

Turn the

Knob

Turn the

Knob

Running interface Press

the Knob

Press

the Knob

Display the

next screen

automatically

after 2 seconds

To switch to “Speed Display”

please see page 9 “Control

Mode” for setting method

Press to exit

In RPM mode

Press the to exit.Adjusting Knob

ID 0.5 INT■

123.4mL/min

▲

Running Interface

Display running interface after initialization.

ID 0.5 INT■

90.5 rpm b.

Flow Rate Display Speed Display

Menu Frame Work

ID 0.5 INT■

123.4mL/min

Running interface

1.Calibration

2. ystem SettingS

3.Control mode

4. xitE

Act Vol 1234：μL

Press to exit

a.Tubing ID

0.5mm

：

b.Test time

0.5min

：

c.Remote

Control:on

d. ump I.D.#.P

e.Footswitch

Gated

f. ackB

Select

RPM Flow

Function Setting

ID 0.5 INT■

123.4mL/min

In running interface, press the to enter the

calibration interface. Turn the to select 4

function setting interfaces.

Adjusting Knob

Calibration Setting

Calibration is needed in below situations:

1.Use the pump the first time; 2. Change the pump head; 3.

Change the tubing; 4. Setting new flow rate; 5. Operating

condition changes.

ID 0.5 INT■

123.4mL/min Tes t ti me

0.5min

：

Cal Vol: 1234 μL

Press to begin

Enter calibration function setting interface:

Note:

In speed Display, the calibration function is forbidden. In Running

Interface, press the , it will display:Adjusting Knob

LEAD-2OPERATINGMANUAL LEAD-2OPERATINGMANUAL

1.Calibration 2. ystem SettingS

3.Control mode

4. xitE

1.Calibration

a. Running direction.

b. Current flow rate and speed.

c. Tubing inner diameter. “ID0.5” means the inner diameter of the

tubing is 0.5 mm.

d. Start/Stop state: “Start” state displays “ ”, “Stop” state

displays “ ”.

Control mode: “INT” means the pump is controlled by internal

control; “shut” means remote control is in “off” state; “V” means

the pump is controlled by remote control analog voltage signal;

“mA” means the pump is controlled by remote control analog

current signal.

■

Running interface

To switch to “Speed Display”

please see page 9 “Control

Mode” for setting method

Press

the Knob

Turn the

Knob

Turn the

Knob

Turn the

Knob

Running interface Press

the Knob

Press

the Knob

Display the

next screen

automatically

after 2 seconds

To switch to “Speed Display”

please see page 9 “Control

Mode” for setting method

Press to exit

In RPM mode

Press the to exit.Adjusting Knob

Flow Rate Calibration:

Start/Stop Key

Start/Stop

Key Adjusting Knob

Adjusting

Knob

Adjusting Knob

1. For the first time flow rate calibration, “System Setting” must

be finished. Please see page 6 for setting method.

2. Press the to begin the testing. Press the

again to stop the testing. The pump stops

automatically and enter “prompt interface” as soon as the

setting time is up. In “prompt interface” press the

to repeat the testing. Press the to enter

actual volume modification interface. Turn the

to input the actual volume and then press the Adjusting

Knob to return to “1. Calibration” interface.

3. Turn the to enter “4. Exit” interface. Press the

to return to “Running Interface”. The flow

rate displayed in the “Running Interface” is actual flow rate.

Turn the to input the required flow rate.

Re-calibrate

Adjust Vol

↑

ID 0.5 INT■

123.4mL/min

System Setting

The submenus of “System Setting” menu are “a. Tubing ID”, “b.

Test time”, “c. Remote Control”, “d. Pump I.D. #”, “e. Footswitch”

and “f. Back”.

Calibration Example

Assumetherequiredflowrateis100μL/min.

ID 0.5 INT■

100.8 L/minμ

ID 0.5 INT■

120.90 L/minμ

ID 0.5 INT■

100 L/minμ

a. Tubing ID

In “System Setting” interface, press the to enter

“a. Tubing ID” interface. Press the to enter

“Select Tubing ID” interface. Turn the to select

the required tubing inner diameter. Press the to

save and return back to “a. Tubing ID” interface.

Adjusting knob

Adjusting Knob

Select Tubing ID

16.43. 4.8

↑

ID 0.5 INT■

123.4mL/min

ID 0.5 INT■

123.4mL/min

LEAD-2OPERATINGMANUAL LEAD-2OPERATINGMANUAL

1.Calibration

1.Calibration 2. ystem SettingS

2. ystem SettingS

4. xitE

Act Vol: 1234 μL

Press to exit

Tes t ti me

0.5min

：

Cal Vol: 1234 μL

Press to begin

Re-calibrate

Adjust Vol

Act Vol: 1234 μL

Press to exit

1.Calibration

a.Tubing ID

0.5mm

：

b.Test time

0.5min

：

c.Remote

Control:on

d. ump I.D.#.P

e.Footswitch

Gated

:f. ackB

a.Tubing ID

0.5mm

：f. ackB

Running interface

Press

the Knob

Press

the Knob

Press

the Knob

Turn the

Knob

Turn the knob to input

therequiredflowrate

Turn the knob to input

the actual volume

Running interface

Press

the Knob

Press

the Knob

Press

the Knob

Press

the Knob

Press

the Knob

Turn the

Knob

Display the

next screen

automatically

after 2 seconds

Turn the

Knob

To switch to “Speed Display”

please see page 9 “Control

Mode” for setting method

System Setting” must be finished

before calibration. Please see

page 6 for setting method

Press

Key

/■

Display Prompt Interface

after testing

Turn the knob to input the

actual volume

Turn the knob to input

therequiredflowrate

Press

the Knob

Press

the Knob

Press

the Knob

Press

the Knob

Press the Knob

Turn t he

Knob

Turn the

Knob

Turn the

Knob

Turn the

Knob

Turn the

Knob

Turn the

Knob

Turn t he

Knob

Running interface

To switch to “Speed Display”

please see page 9 “Control

Mode” for setting method

Running interface

To switch to “Speed Display”

please see page 9 “Control

Mode” for setting method

Press the knob

andthenturn

the knob

Turntheknobtoselect

Flow Rate Calibration:

Start/Stop Key

Start/Stop

Key Adjusting Knob

Adjusting

Knob

Adjusting Knob

1. For the first time flow rate calibration, “System Setting” must

be finished. Please see page 6 for setting method.

2. Press the to begin the testing. Press the

again to stop the testing. The pump stops

automatically and enter “prompt interface” as soon as the

setting time is up. In “prompt interface” press the

to repeat the testing. Press the to enter

actual volume modification interface. Turn the

to input the actual volume and then press the Adjusting

Knob to return to “1. Calibration” interface.

3. Turn the to enter “4. Exit” interface. Press the

to return to “Running Interface”. The flow

rate displayed in the “Running Interface” is actual flow rate.

Turn the to input the required flow rate.

Re-calibrate

Adjust Vol

↑

ID 0.5 INT■

123.4mL/min

System Setting

The submenus of “System Setting” menu are “a. Tubing ID”, “b.

Test time”, “c. Remote Control”, “d. Pump I.D. #”, “e. Footswitch”

and “f. Back”.

Calibration Example

Assumetherequiredflowrateis100µL/min.

ID 0.5 INT■

100.8 L/minμ

ID 0.5 INT■

120.90 L/minμ

ID 0.5 INT■

100 L/minμ

a. Tubing ID

In “System Setting” interface, press the to enter

“a. Tubing ID” interface. Press the to enter

“Select Tubing ID” interface. Turn the to select

the required tubing inner diameter. Press the to

save and return back to “a. Tubing ID” interface.

Adjusting knob

Adjusting Knob

Select Tubing ID

16.43. 4.8

↑

ID 0.5 INT■

123.4mL/min

ID 0.5 INT■

123.4mL/min

LEAD-2OPERATINGMANUAL LEAD-2OPERATINGMANUAL

1.Calibration

1.Calibration 2. ystem SettingS

2. ystem SettingS

4. xitE

Act Vol: 1234 μL

Press to exit

Tes t ti me

0.5min

：

Cal Vol: 1234 μL

Press to begin

Re-calibrate

Adjust Vol

Act Vol: 1234 μL

Press to exit

1.Calibration

a.Tubing ID

0.5mm

：

b.Test time

0.5min

：

c.Remote

Control:on

d. ump I.D.#.P

e.Footswitch

Gated

:f. ackB

a.Tubing ID

0.5mm

：f. ackB

Running interface

Press

the Knob

Press

the Knob

Press

the Knob

Turn the

Knob

Turn the knob to input

therequiredflowrate

Turn the knob to input

the actual volume

Running interface

Press

the Knob

Press

the Knob

Press

the Knob

Press

the Knob

Press

the Knob

Turn the

Knob

Display the

next screen

automatically

after 2 seconds

Turn the

Knob

To switch to “Speed Display”

please see page 9 “Control

Mode” for setting method

System Setting” must be finished

before calibration. Please see

page 6 for setting method

Press

Key

/■

Display Prompt Interface

after testing

Turn the knob to input the

actual volume

Turn the knob to input

therequiredflowrate

Press

the Knob

Press

the Knob

Press

the Knob

Press

the Knob

Press the Knob

Turn t he

Knob

Turn the

Knob

Turn the

Knob

Turn the

Knob

Turn the

Knob

Turn the

Knob

Turn t he

Knob

Running interface

To switch to “Speed Display”

please see page 9 “Control

Mode” for setting method

Running interface

To switch to “Speed Display”

please see page 9 “Control

Mode” for setting method

Press the knob

andthenturn

the knob

Turntheknobtoselect

c. Remote control

Set remote control function.

On: Remote control is permitted.

Off: Remote control is forbidden.

In “System Setting” interface, press and then turn the

to enter “c. Remote Control” interface. Press the

to enter remote control selection interface. Turn the

to select the remote control state. Press the

to save and return back to “c. Remote Control”

interface.

Adjusting

Knob Adjusting

Knob

Adjusting Knob

d.Pump I.D.

When control computer controls many pumps through RS485

interface, it must identify each pump's I.D.. This pump I.D. should

be unique. It's the identification of this pump.

In “System Setting” interface, press and then turn the

to enter “d. Pump I.D.” interface. Press the

to enter pump I.D. setting interface. Turn the

to set the pump I.D. # (1 -30). Press the

to save and return back to “d. Pump I.D.” interface.

Adjusting

Knob Adjusting

Knob Adjusting Knob

Remote Control

On Off

↑

Set ump I.D.#.P

↑

b. Test time

The test time is the required time for one time flow rate

calibration.

In “System Setting” interface, press and then turn the

to enter “b. Test time” interface. Press the

to enter “Set test time” interface. Turn the to set

the test time. Press the to save and return back

to “b. Test time” interface.

Note: The time range is 0.5 25 min. The increment is 0.5 min.

Adjusting

Knob Adjusting Knob

Adjusting Knob

Set test time:

0.5 min

↑

ID 0.5 INT■

123.4mL/min

ID 0.5 INT■

123.4mL/min

ID 0.5 INT■

123.4mL/min

e. Footswitch

Set footswitch working mode.

In “System Setting” interface, press and then turn the

to enter “e. Footswitch” interface. Press the

to enter footswitch setting interface. Turn the

to select footswitch working mode. Press the

to save and return back to “e. Footswitch” interface.

Trigger: Press footswitch, the pump starts running; Press

footswitch again, the pump stops.

Gated: The pump runs as long as the footswitch is pressed.

Adjusting

Knob Adjusting

Knob

Footswitch

Gated Trigger

↑

ID 0.5 INT■

123.4mL/min

LEAD-2OPERATINGMANUAL LEAD-2OPERATINGMANUAL

2. ystem SettingS

b.Test time

0.5min

：

f. ackB

f. ackBf. ackB

f. ackB

c.Remote

Control:on

d. ump I.D.#.P

e.Footswitch

Gated

Press

the Knob

Press the Knob

Press

the Knob

Press the Knob

Press

the Knob

Press the Knob

Press

the Knob

Press the Knob

Turn the

Knob

Turn the

Knob

Turn the

Knob

Turn the Knob to select

Turn the

Knob

TurntheKnobtoselect

Press the knob

andthenturn

the knob

Press the knob

andthenturn

the knob

Press the knob

and then turn

the knob

Press the knob

andthenturn

the knob

Press the knob

andthenturn

the knob

Press the knob

andthenturn

the knob

Press the knob

andthenturn

the knob

Press the knob

andthenturn

the knob

TurntheKnobtoselect

Running interface

To switch to “Speed Display”

please see page 9 “Control

Mode” for setting method

Running interface

To switch to “Speed Display”

please see page 9 “Control

Mode” for setting method

Running interface

To switch to “Speed Display”

please see page 9 “Control

Mode” for setting method

Running interface

To switch to “Speed Display”

please see page 9 “Control

Mode” for setting method

Turn the knob

To set the tim e

Indice

Altri manuali Baoding Longer Precision Pump Pompa dell'acqua

Baoding Longer Precision Pump

Baoding Longer Precision Pump Longer BT300-1F Manuale utente

Manuali Pompa dell'acqua popolari di altre marche

Neptun

Neptun NPHW 5500 Manuale utente

Sensidyne

Sensidyne Gilian BDX-II Istruzioni per l'installazione e il funzionamento

Draper

Draper 47808 Manuale utente

Trolla

Trolla 12820 Manuale utente

Sunfab

Sunfab SVH Series Manuale utente

WilTec

WilTec 50740 Manuale utente

Fieldmann

Fieldmann FVC 5015 EK Manuale utente

Everbilt

Everbilt EFSUB5-122HD Manuale utente

Graco

Graco Husky 3300e Manuale utente

esotec

esotec 101018 Manuale utente

moyno

moyno 2000 CC Manuale utente

Becker

Becker BASIC VASF 2.80/1-0.AC230 Manuale utente

Sykes AmeriPumps

Sykes AmeriPumps GP100M Guida alla risoluzione dei problemi

DUROMAX

DUROMAX XP WX Series Manuale utente

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Manuale utente

Franklin Electric

Franklin Electric IPS Manuale utente

Xylem

Xylem e-1532 Series Manuale utente

Milton Roy

Milton Roy PRIMEROYAL Manuale utente