Barco UST Manuale utente
ENABLING BRIGHT OUTCOMES
Installation manual
UST lens for F-series
Registered office: Barco NV
President Kennedypark 35, 8500 Kortrijk, Belgium
www.barco.com/en/support
www.barco.com
Barco NV
Beneluxpark 21, 8500 Kortrijk, Belgium
www.barco.com/en/support
www.barco.com
R5912118 /01 UST lens for F-series4
1.1 Preparation of the lens
Overview
This lens can be mounted on 4 different projectors and in different position for each projector. E.g. facing up,
facing to the left or facing to the right. For each position the lens has to be rebuild according the its use and
projector type. The motor housing must be turned to the correct position before the lens is mounted in the
projector.
The following positions for the lens are possible:
•For F40: facing up, to the left and to the right (not indicated on drawing)
Image 1-1
•For F70: facing up and to the left
Image 1-2
Do not use for projection to the left when mounted in a frame.
•For F80: facing up and to the left
General
R5912118 /01 UST lens for F-series6
Image 1-6
Be aware that the position for Up and left for F80 is not the same as for the other projector models.
Required tools
Allen key 2 mm with long shaft (delivered with the kit)
How to prepare the lens for all F-series
1. Place the lens on a table. Turn out the 6 screws (1). Use an Allen key with a long shaft so that you do not
damage the screw head. These screws will not be reused.
Note: Always use the correct tool (delivered with the kit) to avoid damage to the screw heads !
1
Image 1-7
General
R5912118 /01 UST lens for F-series 7
1
Image 1-8
2. Slide the motor housing a few mm to the backside of the lens (2) to disengage focusing gear and motor gear.
Motor unit
Focusing gear Motor gear
Disengage
Slide range: 5mm max
Image 1-9
5mm
2
3
A
Image 1-10
Areference marking
3. Rotate the motor housing until the chosen marker on the housing corresponds with the reference marking on
the lens body (steps of 30°). See if the mounting holes matches the holes in the lens body.
E.g. for an FS40 projector, you want to project to the left, then turn the motor housing until the left marking on
the motor housing corresponds with the reference marking on the lens housing.
General
R5912118 /01 UST lens for F-series8
A B C
D E
Image 1-11
AProject LEFT, for F40 and F70
BProject RIGHT for F90 and F40
CProject UP for F40, F70 and F90
DProject LEFT for F80
EProject UP for F80
4. Slide the motor housing back to the front of the lens to re-engage focusing gear and motor gear.
5. Turn in 6 new Allen screws with glue (screws are delivered with the kit). These screws can be multiple times
reused. The turned out old screws can be thrown away.
Use again a tool with a long shaft (Allen key 2 mm, delivered with the kit).
The lens is ready to be mounted on the projector.
How your image is displayed
Projection to the side for any projector:
A B
Image 1-12
ASide view
BTop view
General
R5912118 /01 UST lens for F-series 9
Up projection for any projector:
C D
Image 1-13
CSide view
DBottom view
Extra preparation for F80
1. Slide the lens adaptor on the lens input until it matches the motor housing (1). Make sure the contacts are on
the left top of the adaptor.
1
2
Image 1-14
2. Secure the adaptor by turning it to the right (bayonet fitting) (2).
General
Altri manuali per UST
1
Indice
Altri manuali Barco Lente
Barco
Barco TLD Manuale utente
Barco
Barco UST-Lens Manuale utente
Barco
Barco UST Manuale utente
Barco
Barco QCLD (1.1 - 1.3:1) IRIS Manuale utente
Barco
Barco TLD HB 1.6 Manuale utente
Barco
Barco R9829790 Manuale utente
Barco
Barco R9849975 Manuale utente
Barco
Barco TLD HB (0.8:1) Manuale utente
Barco
Barco QVD (7:1) Manuale utente
Barco
Barco R9849975 Manuale utente
