BARRON TRACE-LITE AXB Manuale utente

IMPORTANT SAFEGUARDS

READ AND FOLLOW ALL SAFETY INSTRUCTIONS.

When using electrical equipment, basic safety precautions should always be followed including the following:

•DISCONNECT AC POWER SUPPLY BEFORE SERVICING.

• Installation and servicing of this equipment should be performed by qualified service personnel only.

• Ensure that the electrical wiring conforms to the National Electrical Code NEC® and local regulations

if applicable.

• Do not mount near gas or electrical heaters.

• Equipment should be mounted in locations and at heights where it will not be readily subjected to tampering

by unauthorized personnel.

•The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition.

• Any modification or use of non-original components will void the warranty and product liability.

• Do not use this equipment for other than intended use.

SAVE THESE INSTRUCTIONS!

Technical Support ■ (623) 580-8943 ■ [email protected]

AXB

Installation Instructions

20070157 REV 1 P-3 12/19 1 800-533-3948 www.barronltg.com

1. Insert anchor bolts in concrete with approximately 2” of exposed

threads in a 2” x 2” square pattern (Fig. 1 & 2) use base plate

template for alignment (see page 3 of instructions).

2. Run the electrical wires (4ft minimum) through bollard base.

3. Slide bollard base over anchor bolts after concrete cures (Fig. 3).

4. Using the washers and nuts provided; loosely tighten the nuts on

the anchor bolts.

5. Level bollard base as needed, leveling screws are not provided.

6. Tighten all four bollard bolts after leveling the bollard base (Fig. 3).

7. Remove lamp assembly from bollard tube (Fig. 4).

8. Slide wires through bollard tube.

9. Slide bollard tube over bollard base and tighten set screws.

10. Make electrical connections to the lamp assembly see Wiring

Connections section.

11. Re-install the lamp assembly to the bollard tube and tighten

set screws.

AXB

Installation Instructions

20070157 REV 1 - 12/19 2 800-533-3948 www.barronltg.com

0.331in

5.28in

2.00in

2.84in

1.161in

2.00in

30°

Anchor Bolt Dimensions

Fig. 1

Spring

Washer

Round

Screw

Washer

Round

Bollard

M8x16

Set Screws

M8 SS

Nuts

Leveling

Screws

(by others)

Bollard

Base

Concrete

Conduit

Fig. 2

Bollard Base

Anchor Bolts

Leveling screws

(by others 1/4-18 UNC)

Fig. 3 Lamp Assembly

Set Screws

Bollar Tube

Set Screws

Bollard Base

Anchor Bolts

Fig. 4

Anchor Bolts

(Approximately

2” exposed)

AXB

Installation Instructions

20070157 REV 1 - 12/19 3 800-533-3948 www.barronltg.com

Wiring Connections

Make electrical connections per Wiring Diagram.

If dimming is not used. Separate the purple and gray wires and cap

individually.

This fixture auto adjusts for voltages between 120VAC-277VAC.

a. Connect the line fixture lead to the black supply lead.

b. Connect the common fixture lead to the white supply lead.

c. Connect the ground lead from the service to the grounding screw?

Troubleshooting

If the unit does not turn “ON”.

1. Check incoming voltage to the LED driver. On the Switch/Un-switch line it must be at lease a minimum of 120VAC and

no greater than 277VAC.

2. Are all LEDs on the light engine “OFF”? If so, the LED driver may be defective. Using a voltmeter, check to see if the

voltage is present at the output of the power supply. If low or no voltage is found, replace the power supply.

3. If any individual LEDs are “OFF” the LED light engine may be defective. Please have the serial number off the light

engine available when you contact technical support.

Base Plate Template

Print actual size

Wire Diagram

Black

White Common

Green/Yellow Green

Ground

Line

Purple

Gray

Note: Two dimming wires are in the driver box.

SCALE 1:1

2”

3”

2”

3”

Altri manuali BARRON Apparecchio di illuminazione

BARRON

BARRON Exitronix NY900U Series Manuale utente

BARRON

BARRON EXITRONIX VEX Series Manuale utente

BARRON

BARRON Exitronix NXFX Series Manuale utente

BARRON

BARRON Exitronix CP-EX Series Manuale utente

BARRON

BARRON Trace-Light LHB Manuale utente

BARRON

BARRON Trace-Light RxA Manuale utente

BARRON

BARRON Trace-Lite TL205 Manuale utente

Manuali Apparecchio di illuminazione popolari di altre marche

Emos

Emos CLASSIC ZY1431T Manuale utente

Westinghouse

Westinghouse Outdoor Lighting Fixture Manuale utente

Hedler

Hedler C 12 silent Manuale utente

Blizzard Lighting

Blizzard Lighting Puck: CSI Manuale utente

Energetic Lighting

Energetic Lighting ELYSL-5004 Series Manuale utente

Lightmaxx

Lightmaxx Shaft 5R Manuale utente

Triarch

Triarch 31083 Manuale utente

Philips

Philips 32614 Series Manuale utente

IKEA

IKEA TIVED Manuale utente

Lightolier

Lightolier LP200 Manuale utente

Chauvet Professional

Chauvet Professional ROGUE R1 BEAM WASH Manuale utente

Martin

Martin MAC 250 Krypton Manuale utente

Cooper Lighting

Cooper Lighting Halo L3232E Manuale utente

Stageline

Stageline ODW-2410RGBW Manuale utente

Light Sky

Light Sky Tornado Series Manuale utente

Lightolier

Lightolier Paralyte 2424 PLA2G9LS26U Manuale utente

Lightolier

Lightolier Lytespan 83ED17S Manuale utente

Lightolier

Lightolier Calculite CS8226 Manuale utente