Basler CXP-12 Manuale utente
QUICK INSTALL GUIDE
BASLER BOOST CXP-12
Basler AG
An der Strusbek 60–62
22926 Ahrensburg
Germany
All material in this publication is subject to change without notice and is
copyright Basler AG.
本出版物中的所有材料如有更改，恕不另行通知，且版权归
Basler AG
所有。
本文書のすべての内容は予告なしに変更される場合があります。また Basler AG
がその著作権を有します。
3
TABLE OF CONTENTS
EN
ZH
JA
TABLE OF CONTENTS
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
About this Document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Important Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Additional Accessories and Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
HARDWARE INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Overview of the Components (Example Installation) . . . . . . . . . . . . . . . . 6
Prerequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Step 1: Installing the Interface Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Step 2: Installing the Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Step 3: Providing Camera Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
ACQUIRING YOUR FIRST IMAGES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Prerequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Acquiring Images Using the pylon Viewer . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4
INTRODUCTION
INTRODUCTION
About this Document
This document provides information about how to install a Basler
boost CXP-12 camera and a Basler CXP-12 Interface Card (referred to here
as "interface card").
It also provides step-by-step instructions that help you to connect the
camera and the interface card and acquire your first images.
Important Documentation
Before installing the hardware, Basler strongly advises reading the
precautions and safety instructions of the following documents:
Basler boost Getting Started Guide (AW001552)
Basler CXP-12 Interface Card 1C Getting Started Guide (AW001558)
Note: This document describes the installation of Basler products only,
i.e., Basler boost CXP-12 cameras, Basler CXP-12 interface cards, and
additional accessories needed for operation, such as cables or cooling
elements.
You can, however, use your own frame grabbers and accessories. In this
case, observe the documentation of the corresponding manufacturers
to ensure proper installation.
5
INTRODUCTION
EN
ZH
JA
For information about how to operate the Basler boost CXP-12 camera and
the Basler CXP-12 interface card, refer to the Basler Product Documentation
available at: docs.baslerweb.com
Additional Accessories and Software
Basler offers the following accessories that allow you to quickly get started
with your Basler boost CXP-12 camera:
CoaXPress 2.0 data cable, Micro-BNC x2 (HD-BNC), 3 m, 5 m, 10 m
Power-I/O cable M8 6p/open, 5 m, 10 m
Heat sink with mounting screws (M4x12)
Mount with mounting screws (M2.5x6), C-mount, F-mount, M42-mount
Power supply 18 W, M8 6p
These products can be purchased individually. Alternatively, you can
purchase the Basler CXP-12 Evaluation Kit boost, which includes a camera,
an interface card, and the accessories listed above apart from the power
supply.
For more information, visit www.baslerweb.com/boost.
The pylon Camera Software Suite (version 6.2 or higher) provides an SDK
for the camera and the interface card. Download the pylon Camera Software
Suite at: www.baslerweb.com/pylon
6
HARDWARE INSTALLATION
HARDWARE INSTALLATION
Overview of the Components (Example Installation)
Fig. 1: Example Installation of a Basler boost CXP-12 Camera with a C-mount Lens and a Basler
CXP-12 Interface Card 1C
VO.1 381JG848
RoHS 2011/65/EU
Status
LED
I/Oconnector
(M8 6-pin)
Micro-BNC
connector
Heat sink
C-mount
C-mount
lens
2 x M4x12
4 x M2.5x6
Power-I/O
cable
CoaXPress
data cable
Micro-BNC
connector
Status
LED
D-Sub Micro-D
connector (15-pin)
PCIe power
connector (6-pin)
7
HARDWARE INSTALLATION
EN
ZH
JA
Prerequisites
The host computer must have at least one PCIe 3.0 x4 slot available on
the main board.
When using Power over CoaXPress (PoCXP), make sure that the power
supply of your computer provides a female 6-pin PCIe power connector.
If none is available, get an appropriate adapter.
If you are not using PoCXP, you need an external power supply.
Make sure that you have a suitable lens and the required accessories to
hand.
Step 1: Installing the Interface Card
1. Make sure that the host computer is shut down and unplugged from the
power outlet.
2. Remove the cover of the computer.
3. Plug the interface card into a free PCIe 3.0 x4 slot of the computer.
4. If you want to power the camera via the interface card (PoCXP), the
interface card needs to be connected to the power supply of the
computer.
Plug the female power supply connector of the computer to the power
connector of the interface card (PCIe 6-pin). If your computer doesn’t
provide a matching power supply connector, use an appropriate adapter.
8
HARDWARE INSTALLATION
5. Put the case of the computer back together.
Step 2: Installing the Camera
1. Make sure that the camera is disconnected from any power supply.
Contamination Hazard: Dust on the sensor may impair the camera’s
performance.
Make sure that the camera is pointing down during the next installation
steps.
2. Remove the seal from the camera front.
3. Attach a mount to the camera.
Note: If you want to use multiple interface cards in the same computer,
make sure that you have one PCIe 3.0 x4 slot per card on the main board
of that computer.
Use an adequate ventilation system within your computer and leave
sufficient free space between your interface card and other cards, if you
use any.
NOTICE
9
HARDWARE INSTALLATION
EN
ZH
JA
Damage Hazard: Inserting the lens too far into the camera may damage
the sensor.
When carrying out the next step, make sure not to insert the lens any
deeper than the specified maximum allowed lens intrusion.
For detailed information, refer to the Basler Product Documentation
available at: docs.baslerweb.com
4. Attach a suitable lens to the camera.
5. Provide sufficient heat dissipation, e.g., by attaching two heat sinks to
the camera.
Step 3: Providing Camera Power
1. If you are using PoCXP:
Plug one end of the CoaXPress cable into the Micro-BNC (HD-BNC)
connector of the camera and plug the other end of the CoaXPress cable
into the Micro-BNC connector of the interface card.
NOTICE
Note: The camera can be powered via PoCXP or via the I/O connector
using an external power supply (AUX power).
If you power your camera by both the CoaXPress interface and the
I/O connector, the power provided by the I/O connector is used only.
10
HARDWARE INSTALLATION
2. If you are using an external power supply:
a. Plug one end of the CoaXPress cable into the Micro-BNC (HD-BNC)
connector of the camera and plug the other end of the CoaXPress
cable into the Micro-BNC port of the interface card.
b. Connect the plug of the power I/O cable to the M8 6-pin connector
of the camera.
Observe the following pin assignment.
c. Connect the open end of the power I/O cable to a power supply.
d. Plug the power supply into a power outlet.
3. Reconnect the computer to the power outlet and boot the computer.
For information about the different LED states and corresponding colors,
refer to the Basler Product Documentation available at:
docs.baslerweb.com
Pin Line Function
I/O connector
of the camera
(M8 6-pin)
1 24 VDC camera power
2 1 Opto-coupled I/O input line
3 Ground for opto-coupled I/O lines
4 2 General purpose I/O (GPIO) line
5 3 General purpose I/O (GPIO) line
6 Ground for camera power and GPIO lines
6
4
35
21
Indice
Lingue:
Altri manuali Basler Macchina fotografica digitale
Basler
Basler racer Manuale utente
Basler
Basler A620f Manuale utente
Basler
Basler blaze-101 Manuale utente
Basler
Basler A302f Manuale utente
Basler
Basler aviator Manuale utente
Basler
Basler A202k Guida alla configurazione
Basler
Basler acA2040-55 Manuale utente
Basler
Basler WOOD BURNING FIREPLACE Manuale di installazione e d'uso
Basler
Basler A202k Manuale utente
Basler
Basler Pioneer Manuale utente
Basler
Basler ace acA640-90gm Manuale utente
Basler
Basler daA2500-14um Manuale utente
Basler
Basler acA1300-75gc Foglio di istruzioni
Basler
Basler A101f Manuale utente
Basler
Basler ace Manuale utente
Basler
Basler GigE CAMERAS Manuale utente
Basler
Basler Racer raL2048-48gm Manuale utente
Basler
Basler L301kc Manuale utente
Basler
Basler A600f Guida alla configurazione
Basler
Basler dart Manuale utente
