Bastl Instruments Popcorn CV INPUTS Manuale utente
instruction
MIN/MAJ is a gate input which inverts the Minor/Major
setting of the quantizer.
TRIG A S. is a CV input to set how many steps are advanced
by triggering the TRIG A input. When the TRIG A knob is set
fully CCW, 0 volts corresponds to -4 and 5 volts correspond
to +4.
GATE T. CV input adds to the gate time.
SLIDE T. CV input adds to the slide time.
CV on the OFFSET input immediately adds a certain offset
to the ACTIVE step position. The offset is 0 to 7 steps
corresponding to 0 to 5 volts.
Pocorn Exanders
CV INPUTS
GATE OUT
1
2
3
4
5
6
7
8
JUMP
GAT E
OUTS
OFFSET
SLIDE T.
GATE T.
TRIGA S.
MIN/MAJ
OFFSET BITS
CV INPUTS
POPCORN EXPANDER
A
A
B
C
D
E
D
E
F
G
C
B
bu this than?
r wife will be...
features
gate input for selecting minor or major setting of the
quantizer
CV input for Gate Time
CV input for Slide Time
CV input for how many steps are jumped by trigger A
CV step address offset
alternative mode in which 3 of the CV inputs acts as 3
binary gate bits to select the addressed step (instead of
Gate & Slide time and trigger A steps)
technical details
2HP width
connects to the popcorn sequencer
Alternave CV In Mode:
The Bit Offset
There are two modes for the CV Expander: the normal
(described above) and the alternative. The alternative
mode can be activated in the boot menu. In the
alternative mode the connectors B,C and D are used
as offset bits. This means that you can to set the
binary address of the cursor offset by sending gates
to the inputs. This can be extremely useful when used
with a gate sequencer because you can directly select
which step is activated with the combination of the 3
gate inputs. High gate on connector B will offset the
address by one step (least significant bit), high gate on
connector C will offset the address by two steps and
high gate on the D connector will offset the address by
four steps (most significant bit). Here are all 8 possible
combinations of these gates and how they corresponds
to the 8 steps.
POPCORN CV INPUTS EX.
Adds more CV inuts for enhanced control of the nonline-
ar browsin throuh the stes. All inuts on the exander
react onl to ositive voltaes 0-V.
Ste Offset D
0
1
2
3
4
5
6
7
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
C B
www.bastl-instruments.com
Carefull
!
red=master
red=slave
GATE
EXPANDER
CV_EXPANDER
**
seqExp v1.0
-12
GND
UPLOAD
CHAIN
POWER
red
C
A
B
L
E
S
C
A
B
L
E
S
P C B Popcorn
CV Inputs ExpanderGate Out Expander
!
instruction
Holding the JUMP button and pressing one of the STEP
buttons will make that step ACTIVE. The sequencer can
change the step only after the STEP button is released
again.
The Gate Outputs correspond to steps 1-8. The expander
ALWAYS outputs the gate for the current step regardless if
the gate is set to ON or OFF in GATE MODE. The gate time is
the global gate time. If gate time is fully CW the gate holds
HIGH while the step is active. The gates are 0-5 volts.
POPCORN GATE OUT EX.
Adds individual ate oututs for ever ste, lus a um
button which allows ou to chane stes manuall.
features
individual gate output for every step
jump button – hold jump and press a step button
to jump to that step
technical details
2HP width
connects to the popcorn sequencer
Follow the diagram to connect the ribbon cable to
the Popcorn. Please make sure the polarity of the
cable is not reversed!
connectin the exander
F
G
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Bastl Instruments Estensione
