BaudTec TW263R4 Manuale utente
1
Package Content
Installation & Setup
BAUDTEC TW263R4 ADSL2+ MODEM
ROUTER
System Requirements
1. Pentium 200 MHZ processor or above
2. Windows 98SE, Windows Me, Windows 2000, Windows XP and
Windows Vista.
3. 64 MB of RAM or above
4. 25 MB free disk space
For Annex-B TW263R4-B2
ADSL2+ Router
1. ADSL2+ Wireless Router
2. CD-ROM (Software & Manual)
3. Quick Installation Guide
4. 2 x Telephone Cables (RJ-11)
5. Ethernet Cable (RJ-45)
6. AC Adaptor
7. Annex B Splitter (ATF057)
For Annex-A TW263R4-A2
ADSL2+ Router
1. ADSL2+ Wireless Router
2. CD-ROM (Software & Manual)
3. Quick Installation Guide
4. 2 x Telephone Cables (RJ-11)
5. Ethernet Cable (RJ-45)
6. AC Adaptor
7. 2 x Annex A Splitter (ATF085A1R)
Follow each STEP carefully and only go to the next step once you have
completed the previous STEP.
The Ethernet port no# 4 is
ONLY FOR IPTV
and cannot be utilized as
normal Ethernet port.
2
STEP 1
Connection of ADSL2+ Modem Router
If you have an ISDN telephone line connect the modem router as shown
below:
1. Connect one end of the RJ-45 Ethernet Cable to your PC’s Ethernet port
and the other end to one of the 4"LAN" ports of the Wireless ADSL
MODEM ROUTER.
2. Connect the supplied RJ11 telephone cable from your office's telephone
jack to the "LINE " port of the supplied ATF057 splitter. Connect another
RJ11 telephone cable to the "MODEM" port of the splitter and connect the
other end of this cable to the "LINE" port of your WLAN ADSL2+ Router.
3. Connect a RJ11 telephone cable to the "PHONE" port of the splitter and
connect the other end to the input which is underneath the NETMOD/NT1
OTE unit.
4. Connect the power adapter to the power inlet "POWER" of the ADSL2+
WiFi Router and turn the "ON/OFF SWITCH" to switch of your ADSL2+
WiFi Router on and wait for 2 minutes before moving to the next step.
3
If you have a PSTN telephone line (normal analog line) connect the router
as shown below:
1. Connect the supplied RJ45 Ethernet cable from your PC's Ethernet port to
one of the 3 LAN ports of the ADSL2+ Router's. ATTENTION: The LAN
port no 4 (purple marking) can only be used for Set-Top-Box (STB)
connection.
2. a) Connect the supplied RJ11 telephone cable from your home's telephone
jack to the “LINE” port of your ADSL2+ Router.
b) In case you use a telephone device on the same home telephone jack,
please plug the RJ11 telephone cable from your home’s telephone jack to
the “LINE” port of the supplied ATF085A1R splitter. Connect the second
one supplied RJ11 telephone cable to the “DSL” port of the supplied splitter
and the other end of this cable to the “LINE” port of your ADSL2+ Router.
3. Connect an RJ11 telephone cable to the “PHONE” port of the splitter and
connect the other end to your telephone device. In case you have more
than one telephone devices on other telephone sockets in your house, you
have to place a splitter between them and the telephone jack. Connect
together, using an RJ11 telephone cable, the “LINE” port of the splitter with
your telephone jack.
4. Connect the power adapter to the power inlet “POWER” of the ADSL2+
Router and turn the “ON/OFF SWITCH” to switch of your ADSL2+ Router
on. And wait for 2 minutes before moving to the next step.
4
LED Meaning
Your WLAN ADSL2+ Router has indicator lights on the front side.
Please see below for an explanation of the function of each indicator light.
: Power indicator
: ADSL Link indicator
: Internet Active indicator
: Wireless Active indicator
: Ethernet Active indicator
Table 1.1: LED function
Label Color On Flash Off
Green Ready Not Ready Power Off
Green Connect to
DSLAM
Disconnect to
DSLAM N/A
Green Connect to
Internet / IDLE
Transmit /
Receive Data
Disconnect to
Internet
Green N/A Wireless Active Deactivated
Green Ethernet
Connected
Transmit /
Receive Data
Ethernet
Disconnected
5
STEP 2
Configuration Procedures
Before starting the WLAN ADSL2+ Router configuration, please kindly
configure the PC computer as below, to have automatic IP address /
DNS Server.
For Windows 98SE / ME / 2000 / XP
1. Click on " Start " -> " Control Panel " (in Classic View).In the Control
Panel, double click on " Network Connections " to continue.
2. Single right click on " Local Area connection ", then click
" Properties ".
6
3. Double click on " Internet Protocol (TCP/IP) ".
4. Check " Obtain an IP address automatically "and " Obtain DNS
server address automatically " then click on " OK " to continue.
5. Click " Show icon in notification area when connected " (see screen
image in 3. above) then Click on " OK " to complete the setup
procedures.
7
For Windows Vista-32/64
1. Click on " Start " -> " Control Panel " (in Classic View) -> " Network
and Sharing Center ". In the Manage network connections, double click
on " Manage network connections " to continue.
2. Single right click on " Local Area connection ", then click
" Properties ".
8
3. The screen will display the information " User Account Control " and
click " Continue " to continue.
4. Double click on " Internet Protocol Version 4(TCP/IPv4) ".
5. Check " Obtain an IP address automatically " and " Obtain DNS
server address automatically " then click on " OK " to continue.
6.You can see the screen will appear as shown in step 4. above, then click
on " OK " to complete the setup procedures.
9
STEP 3
WLAN ADSL2+ Router Configuration
1. Please insert the supplied CD into your CD-ROM drive.
2. The CD should auto-start, displaying the window shown in 3. below. If
your CD does not start automatically go to Windows Explorer, Select your
CD drive and double click " setup.exe ".
3. Please choose your language (Greek or English) and then click button to
continue.
4. Please click " Ethernet connection " button to continue.
Indice
Altri manuali BaudTec Router di rete
Manuali Router di rete popolari di altre marche
NETGEAR
NETGEAR FS526T - Switch Manuale utente
Korenix
Korenix JetNet 5710G Series Manuale utente
Automated Logic
Automated Logic ZN551 Manuale del proprietario
Cisco
Cisco ASR 1000 Series Manuale dell'operatore
EnGenius
EnGenius ESR-9710 Manuale utente
Cisco
Cisco 805 Series Istruzioni operative e di sicurezza