Baxter Flo-Gard 6301 Manuale utente

Operator's Manual

Flo-Gard® 6301

Dual Channel Volumetric

Infusion Pump

Table of Contents

Introduction..............................................................................................1

Physical Description...............................................................................3

Operating Instructions..........................................................................10

Precautions ......................................................................................10

Loading the Pumps...........................................................................11

Starting a Primary Infusion ...............................................................15

Starting a Secondary Infusion...........................................................18

Using Volume-Time Programming....................................................19

Changing the Flow Rate While the Pump Is Running.......................21

The OPTIONS Key ...........................................................................22

Using the Programmed Delivery Profile Feature........................22

Computer Control.......................................................................25

Computer Monitoring..................................................................26

Locking the Front Panel....................................................................26

Battery Powered Operation ..............................................................27

FLOW CHECK Information Display..................................................27

Cleaning and Storage ...........................................................................28

Alerts and Alarms .................................................................................29

Technical Specifications ......................................................................34

Configurable Options............................................................................36

Warranty and Service Information.......................................................41

Warranty ...........................................................................................41

Service Information ..........................................................................42

7-19-B1-564 i

Change record

7-19-01-564

Original issue: 7/92

Rev. A: 9/92

Rev. B: 05/93

Page Revision

Front cover 0

ii B

1–4 0

6–8 0

10–14 B

15 0

16–17 B

18-30 0

31–32 B

33 0

34 A

35–38 0

39–42 B

Back cover B

A zero in the “Revision” column indicates original issue.

ii 7-19-B1-564

Introduction

The lo-Gard®6301 Dual Channel Volumetric Infusion

Pump from Baxter can deliver a wide variety of fluids over

a broad range of infusion rates. The device's features in-

clude:

•Uses only standard Baxter®solution administration

sets.

•Two separate pump channels allow it to do the work

of two conventional pumps, resulting in space sav-

ings.

•Configurable settings allow the device to be custom-

tailored to best suit the hospital's needs.

•Computer control capability allows remote control

or monitoring of the device via a standard RS-232C

interface.

•Infuses a wide variety of fluids, including blood and

fat emulsions.

•Suitable for use in epidural administration.

•Safety clamp automatically occludes the tubing

when the pump door is opened.

•Occlusion sensors detect both upstream and down-

stream restrictions. Sensitivity of the downstream

occlusion sensor is selectable through the device's

configuration.

•low check display shows resistance to flow.

•Ultrasonic air-in-line detectors. Sensitivity of the

air detectors is selectable through the device's con-

figuration.

•Each pump channel features a Programmed Deliv-

ery Profile that enables programming of up to 10 se-

quential infusion programs for situations where

ramping of medications are indicated.

7-19-B1-564 1

•Slide clamp loading option provides flow shut-off

when I.V. set is removed from the pump.

•Locking control panel helps prevent patient tamper-

ing.

•Each pump channel features an independent secon-

dary medication program. The channel automati-

cally switches over to the primary program upon

completion.

•Volume-Time programming automatically calcu-

lates flow rate.

•Automatic self-test routine checks for proper func-

tion before use.

•ive-hour memory retains infusion data after

power-off.

•Easily replaceable fuse, battery, and power cord.

•Access to test points and internal program simpli-

fies servicing and software upgrades.

•Device can be configured to display a hospital area

designator, such as “

ONCOLOGY

”or“

CARDIAC

ICU

,” upon power-up.

2 7-19-B1-564

Physical Description

Items 1 through 9 are associated with Pump 1 and are de-

scribed below. The controls associated with Pump 2 are

identical and function in exactly the same manner. Items 10

through 28 are common to the operation of both pumps. All

front panel items are shown in igure 1.

Front Panel

ITEM FUNCTION

1. Pump 1 ON

OFF/CHARGE key Turns Pump 1 on and off. The internal battery charger re-

mains on regardless of the ON OFF/CHARGE key as long as

the device is plugged in.

2. Pump 1 door

latch Opens and closes pump door for I.V. set loading and removal.

3. Pump 1 STOP key Stops Pump 1 until further instructions are given. The mes-

sage

STOPPED

appears when the key is pressed. An alert

sounds if Pump 1 is stopped for more than two minutes.

Clears all programming alerts while pump is running.

4. PUMP 1 key and

indicator Allows keypad and other controls common to both pumps to

accept data for Pump 1 programming. Yellow LED lights to in-

dicate that Pump 1 is selected.

5. Pump 1 main dis

play Shows rate, volume to be infused (VTBI), and total volume in-

fused for Pump 1 primary and secondary infusion programs.

The decimal point is displayed as an underscore (example:

99_9).

6. Pump 1 message

display Shows all Pump 1 messages and messages that apply to the

device as a whole.

7. Pump 1 ALARM

LED Red LED that blinks on and off during a Pump 1 or general

alarm, accompanied by a message display and a repeated se-

quence of three tones. An alarm indicates that Pump 1 or the

device as a whole requires immediate attention.

8. Pump 1 PUMPING

LED Green LED which is constantly lit while Pump 1 is pumping.

9. Pump 1 ALERT

LED Yellow LED which lights during Pump 1 and general alerts,

accompanied by a message display and a repeated single tone.

An alert indicates that Pump 1 or the device as a whole needs

timely attention.

7-19-B1-564 3

Front Panel

ITEM FUNCTION

10. BACK LIGHT key Backlights the displays when pressed. Pressing the key again

turns the backlight off. If the device is operating on battery

power, the backlight remains on for 60 seconds when the

BACK LIGHT key is pressed.

11. SILENCE key Temporarily silences an audible alarm or alert for two min-

utes, unless another alarm or alert occurs on either pump

within the two-minute silence period. All messages remain

displayed.

12. NEXT legend Lights when theTOT VOL STATUS key is functioning as the

NEXT key.

13. TOT VOL/STATUS

key Displays total volume delivered for each pump. The key is also

used to advance to the next step when programming a delivery

profile. (See NEXT legend, item 12 above.)

14. CLEAR TOT VOL

key Resets the total volume delivered by the selected pump to zero

if pressed when the pump is stopped.

15. TIME key Enters the time over which an infusion is to take place during

Volume-Time programming.

16. PRI RATE key Allows programming of the primary infusion rate for the se-

lected pump.

17. PRI VTBI key Allows programming of the primary VTBI for the selected

pump.

18. PRI START key Starts the primary infusion for the selected pump.

19. Plug icon Always lit while the device is plugged in and the battery is

charging.

20. MONITOR legend Lights when the device is being queried by the computer dur-

ing computer monitoring.

21. Battery icon Lights when the device is operating on battery power.

22. COMPUTER CON

TROL legend Lights when the device is being controlled by a remote com-

puter.

23. CLR key Clears any programming values currently being entered.

24. SEC START key Starts the delivery of the secondary infusion for the selected

pump.

4 7-19-B1-564

Front Panel

ITEM FUNCTION

25. SEC VTBI key Allows programming of the secondary VTBI for the selected

pump.

26. SEC RATE key Allows programming of the secondary infusion rate for the se-

lected pump.

27. Numerical keypad Programming values and decimal point are entered with these

keys.

28. OPTIONS key Allows the device to enter an enabled optional mode. These

may include the Programmed elivery Profile (P P) or Com-

puter Control modes. If Programmed elivery Profile and/or

Computer control is available, the OPTIONS key is lit.

7-19-B1-564 5

Rev. A

P MPING

ALERT

PRI

START

CLR

ALARM

PRI

VTBI

PRI

RATE

SEC

RATE SEC

VTBI SEC

START COMP TER

CONTROL

MONITOR

P MPING

ALERT ALARM

P MP

CLEAR

TOT VOL

STOP

TIME

BACK

LIGH T

OFF

CHARGE

STOP

OPTIO NS

TOT VOL

STAT S

VOL METRIC INF SION P MPD AL CHANNEL

Flo-Gard® 6301

SILENCE

CHARGE

OFF

78910 11 12 13 14 15

Figure 1. Front View

igure 2 shows Pump 2 only. Pump 1 has identical features,

which function in the same manner.

Pump Head Features

ITEM FUNCTION

1. Upstream occlusion sensor Detects a tubing restriction upstream of the

pump.

2. Pumping fingers The linear peristaltic pump mechanism consists

of cam-driven pumping fingers which succes-

sively manipulate the tubing against the back-

plate, resulting in fluid movement in a

downward direction.

3. Downstream occlusion

sensor Detects tubing restrictions downstream of the

pump. The sensitivity level can be adjusted to

suit the needs of the hospital through the de-

vice's configuration.

4. Air sensor Detects air bubbles in the tubing. The sensitivity

is adjustable via the device's configuration.

5. Safety clamp Prevents accidental fluid flow by automatically

occluding the tubing whenever the pump door is

opened.

6. Slide clamp slot The slide clamp loading option is selectable

through the configuration. When the slide clamp

loading option is enabled, the I.V. set's slide

clamp must be inserted into this slot. The opera-

tor must push the slide clamp into the slot to oc-

clude the tubing before the I.V. set can be

removed from the pump.

7. Slide clamp spring retainer If your hospital has not selected the slide clamp

loading option, this spring retainer is inserted

into the slide clamp slot, preventing the insertion

of the slide clamp.

6 7-19-B1-564

Altri manuali per Flo-Gard 6301

Indice

Altri manuali baxter Pompa dell'acqua

baxter

baxter Auto Syringe AS50 Manuale utente

baxter

baxter Flo-Gard 6201 Manuale utente

baxter

baxter Flo-Gard 6301 Manuale utente

baxter

baxter ExactaMix 2400 Compounder Manuale utente

baxter

baxter Colleague CXE Manuale utente

baxter

baxter Auto Syringe AS50 Manuale utente

baxter

baxter 35700BAX Istruzioni per l’uso

baxter

baxter 35700BAX2 Manuale utente

baxter

baxter PCA II Manuale utente

Manuali Pompa dell'acqua popolari di altre marche

Neptun

Neptun NPHW 5500 Manuale utente

Sensidyne

Sensidyne Gilian BDX-II Istruzioni per l'installazione e il funzionamento

Draper

Draper 47808 Manuale utente

Trolla

Trolla 12820 Manuale utente

Sunfab

Sunfab SVH Series Manuale utente

WilTec

WilTec 50740 Manuale utente

Fieldmann

Fieldmann FVC 5015 EK Manuale utente

Everbilt

Everbilt EFSUB5-122HD Manuale utente

Graco

Graco Husky 3300e Manuale utente

esotec

esotec 101018 Manuale utente

moyno

moyno 2000 CC Manuale utente

Becker

Becker BASIC VASF 2.80/1-0.AC230 Manuale utente

Sykes AmeriPumps

Sykes AmeriPumps GP100M Guida alla risoluzione dei problemi

DUROMAX

DUROMAX XP WX Series Manuale utente

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Manuale utente

Franklin Electric

Franklin Electric IPS Manuale utente

Xylem

Xylem e-1532 Series Manuale utente

Milton Roy

Milton Roy PRIMEROYAL Manuale utente