BBG KDAEC Series Manuale utente

KDAEC

Instruction Manual

KD-AEC-en,V1.1-2011

Additions (Interior Calibrate)

1. Enter the FACTORY PARAMETERS mode(see section

13.2~13.3),while the display show ”Pi”, Press the twice, and

press the key three times, and then press the key four

times, the display will show “PASS”.

2. Press the key, and then the display will show the

Readability of the scale now, press the the key to choose

the proper parameter, and then press the key to confirm.

3. The display will show the capacity of the scale now, press the the

key to choose the proper parameter, and then press the

key to confirm.

4. Now the display will show the AD count, press the key to

enter in the factory calibration.

5. The display show “ZERO”, clear the other things on the

platform, and the press the key to confirm. Place the correct

calibration mass as selected by the user at the centre of the pan,

and press the key to confirm, until the scale return to the

normal weighting mode.

TABLE OF CONTENTS

1.0 INTRODUCTION------------------------------1

2.0SPECIFICATIONS-----------------------------1

3.0INSTALLATION--------------------------------3

4.0 KEYPAD------------------------------------------4

5.0DISPLAY------------------------------------------5

6.0 SYMBOLS AND INDICATORS------------5

7.0 BATTERY----------------------------------------5

8.0 BACKLIGHT------------------------------------5

9.0 AUTO POWER OFF---------------------------6

10.0 OPERATIONS---------------------------------6

11.0 USB INTERFACE-----------------------------7

12.0CALIBRATION---------------------------------9

13.1 USER PARAMETERS-----------------------10

13.2TECHNICAL PARAMETERS--------------15

13.3FACTORY PARAMETERS-----------------17

14.0ERROR MESSAGES--------------------------18

Additions (Interior Calibrate) ------------------19

1.0 INTRODUCTION

The KDAEC range of Platform Scales has a stainless steel top pan

on a steel frame and an indicator with a large backlit LCD. The

keyboard has 4 easy to use function keys , , and

. All scales are supplied with the Power Supply module.

2.0 SPECIFICATIONS

Modle KDAEC

KDAEC

30M

KDAEC

75 M

KDAEC

75 L

KDAEC

150

KDAEC

150 M

KDAEC

150 L

KDAEC

200 M

KDAEC

200 L

KDAEC

200 M

KDAEC

300 L

30 kg x

0.01kg

75 kg x

0.02 kg

150 kg x

0.05 kg

200 kg x

0.05kg

300 kg x

0.1kg

66 lb x

0.02 lb

165 lbx

0.05 lb

330 lb x

0.1 lb

440 lb x

0.1 lb

660 lb x

0.2 lb

1058 oz

x 0.5 oz

2645 oz

x 1 oz

5291 oz

x 2 oz

7054 oz

x 2 oz

10582oz

x 5 oz

Capacity x

Readability

d=e=

66 lb:16

x 1 oz

165 lb:16

x 1 oz

330 lb:16

x 2 oz

440 lb:16

x 2 oz

660 lb:16

x 5 oz

Repeat-ability

0.01 kg /

0.02 lb

0.02 kg /

0.05 lb

0.05 kg /

0.1 lb

0.05 kg /

0.1 lb

0.1 kg /

0.2 lb

Linearity 0.02 kg /

0.04 lb

0.04 kg /

0.1 lb

0.10 kg /

0.2 lb

0.10 kg /

0.2 lb

0.2 kg /

0.4 lb

14.0 ERROR MESSAGES

During the initial power-on testing or during the operation

the scale may show an error message. The error

messages are described below.

ERROR

CODE

DESCRIPTION POSSIBLE CAUSES

nnnnn

A continuous beep is heard.

Weight on the pan

exceeds the capacity of

the scale. Remove the

weight from the pan.

CALEr If the selected mass is less

than 10% or more than 20% of

the capacity of the scale, an

error message “CALEr” will be

displayed and the scale will

return to zero.

Incorrect calibration

mass. Repeat the process

correctly.

If an error message is shown, repeat the procedure that

caused the message such as turning the scale on,

calibration or any other functions. If the error message is

still shown, contact your supplier for further support.

13.2.4 STABILIZATION TRACKING

This parameter is for setting the size of the tracking range to

indicate the stability. This is used to stable the scale once a

weighing result is achieved.

Press to scroll through the settings. The display will show

“Str 1” to “Str 5”. If it is set to “Str 1” then the stability range is at its

smallest and “Str 5” the highest.

 When the desired value is displayed, press the key to

select the value and exit the Technical Parameters. The

display will count down to zero and the scale will return to

normal weighing.

 If is pressed instead of the key, the display will

ask for Pin for entering into the Factory Parameters. Switch

off the scale.

 Switch on the scale to start the operation.

13.3 FACTORY PARAMETERS

If after the last Technical Parameter key is pressed, the

scale will advance to the Factory Parameter section. This section

contains critical calibration reference information and is protected

by a Pin Code which can only be accessed by a qualified technician.

To exit, the user must switch off the scale when the display shows

“Pi”.

I. Platform size

KDAEC(30kg/75kg/150kg) 390 x310 x 40mm

KDAEC M (30kg/75kg/150kg/200kg/300kg) 500 x500 x40mm

KDAEC L

(75kg/150kg/200kg/300kg)

900 x600 x40mm

POWER-supply 4 x1.5VAA battery/DC 5V/ USB

adaptor 5V(optional)

Indicator Dimensions (wxdxh) 215 x 100x 70 mm

Stabilization time 2-3 seconds

Tare Full range tare by subtraction

Weighing units kg, lb, oz, lb.oz

Calibration

Automatic External -user selectable

cal weight

Interface Bi-directional USB

Operating temperature 0°C to 40°C

Humidity Up to 90% RH non-condensing

Display

25 mm Backlit LCD digits with

weight legends for kg, lb, oz, lb.oz

and low battery, stable, zero, net

weight and Hold symbols

Keypad Mechanical switches under overlay

Scale housing

Indicator: Aluminium

Platform: Mild steel base and

stainless steel pan

Applications

Weighing, Dynamic / Animal

weighing, Display Hold

3.0 INSTALLATION

3.1 UNPACKING

The scales come with-

Standard KDAEC KDAEC M KDAEC L

√

KDAEC Indicator with bracket and 2 screws

The Platform

Stainless Steel Pan

Power supply Module

An Instruction manual

3.2 LOCATING

 The scales should not be placed in a location that will reduce

the accuracy.

 Avoid extremes of temperature. Do not place the scale in direct

sunlight or near air conditioning vents.

 Avoid unsuitable surfaces. The table or floor should be rigid

and free from vibration.

 Avoid unstable power sources. Do not use the scale near

large users of electricity such as welding equipment or large

motors.

 Do not place the scale near vibrating machinery.

 Avoid high humidity that might cause condensation. Avoid

direct contact with water. Do not spray or immerse the scales

in water.

 Avoid air movement such as from fans or opening doors. Do

not place the scale near open windows or air-conditioning

vents.

 Keep the scales clean. Do not stack material on the scales

when they are not in use.

 To return to normal weighing, turn the scale off and back to on

again or press the key.

13.2.1 FILTER

This parameter is for setting the speed of the display filter. For

poor environments the filter should be set at its slowest to minimise

external influences on the scale. For weighing small samples

or gradual filling, the filter should be set at a faster setting.

Press to scroll through the options. The display will show

“FiL 1” to “FiL 3”. If it is set to “FiL 1” then the display is at its

slowest setting and at “FiL 3” the display is in its fastest setting.

13.2.2 ZERO TRACKING

This parameter is for setting the range of the zero tracking. Zero

tracking will aid the scale to hold or return to zero and should be

increased if large weights are left on the scale or temperature is

not consistent.

Press to scroll through the settings. The display will show

“ZEo 1” to “ZEo 8”. If it is set to “ZEo 1” the zero tracking is at its

smallest range and “ZEo 8” the highest.

13.2.3 STABILIZATION RANGE

This parameter is for setting the range of the stability indicator. This

is used to determine when the scale will print automatically

as well as indicate that the weight is stable.

Press to scroll through the settings. The display will show

“StA 1” to “StA 8”. If it is set to “StA 8” then the stability is at its fastest

and “StA 1” the slowest.

Hod

USB

communication

is off Hold occurs

when the

key is pressed.

Hold is released

if is

pressed again or

time expires as

per Hti setting.

USB print

continuously. Hold

occurs when the

key is

pressed. Hold is

released if is

pressed again or

time expires as per

Hti setting.

USB prints and the hold

occurs when is

pressed. If is

pressed a second time

print will occur again.

Hold is released if

is pressed again

or time expires as per

Hti setting.

13.2 TECHNICAL PARAMETERS

The technical parameters allow adjusting of the scale for accuracy

and speed. See the below for the complete list of parameters.

 Switch off the scale.

 Hold the key and then press momentarily.

Release the key. The display shows the first technical

parameter to set the filter “FiL x”.

 To exit the parameter setting at any time, press the key.

 To scroll through the technical parameters, press the

key (which will advance to the next parameter).

3.3 SETTING UP

NOTE: When moving the scale, take care to prevent bending of the cable and

connector too much as over a period of time this can weaken the wires in the

connector and cause malfunction.

4.0 KEYPAD

Turns the scale on or off only

Sends data via USB and combines with Hold functions, if

enabled

Selects kilograms, pounds, ounces or pounds-ounces

Sets the display to true zero or net zero by storing the current

weight in the tare memory

5.0 DISPLAY

6.0 SYMBOLS AND INDICATORS

Symbol Description

Scale is in the zero position

Weighing result is stable

kg , lb, oz or lb.oz

Active weighing unit

Battery is weak

Net weight is being displayed

Hold Display is held as per the Hold parameter setting

7.0 BATTERY

When the battery needs charging a symbol on the display will turn

on. The battery should be changed when the symbol is on, or

connect the power supply module to the rear of the indicator and

apply power. The scale need not be turned on.

8.0 BACKLIGHT

The backlight for the LCD can be set by the user to always off,

always on or automatic (on only when the scale is in use or a key is

pressed). See setting of the parameter in section 13.1.2.

is set to “Hod 2” or “Hod 3”.

1.Hti 0 : Holds the display for an infinite time limit

2.Hti 1 : Holds the display for 15 (1 x 15) seconds

3.Hti 2 : Holds the display for 30 (2 x 15) seconds

4.Hti 3 : Holds the display for 45 (3 x 15) seconds

5.Hti 4 : Holds the display for 60 (4 x 15) seconds

Press the key to confirm the selection and move back tofirst

parameter or press to exit the parameter setting.

HOLD AND PRINTING TABLE:

trn 1 trn 2 trn 3

Hod

USB communication

is off. Hold is off.

key has no

function.

USB prints

continuously. Hold

is off. key

has no function.

USB prints when

is pressed.

Hold function is

disabled.

Hod

USB communication

is off. Hold occurs

automatically when

the weight is stable.

Hold is released if

is pressed or

time expires as per Hti

setting.

USB print

continuously. Hold

occurs

automatically when

the weight is stable.

Hold is released if

is pressed or

time expires as per

Hti setting.

USB prints and hold

occurs automatically

when the weight is

stable. key is

pressed print will occur

again. Hold function is

released if the key is

pressed again or time

expires as per Hti

setting.



1.trn 1 : No data output

2.trn 2 : Continuous data output

3.trn 3 : Normal output when the key is pressed.

13.1.8 SELECTION OF HOLD FUNCTION

The eighth parameter is to set the Hold function. Display will show

“Hod 3” (DEFAULT SET). See the HOLD AND PRINTING TABLE in

section 13.1.9.

1.Hod 1 : No hold function

2.Hod 2 : Automatic hold function

3.Hod 3 : Manual hold function

If selection of “Hod 2” or “Hod 3” is made then it will lead to

SETTING OF HOLD TIME LIMIT (see section 13.1.9). The

display will show “Hold” above the weight during operation. If “Hod

1” is selected, pressing the key will take you back to the first

parameter on Auto Power Off. If you want to return to weighing,

press the key.

13.1.9 SETTING OF HOLD TIME LIMIT

This parameter is to set the time limit by which the display is held

after the hold function is used. It is applicable if the hold function

9.0 AUTO POWER OFF

The auto power off can be set by the user to disable the feature or

to apre-set time interval. See setting of the parameter in section

13.1.1.

10.0 OPERATIONS

10.1 SWITCHING ON THE SCALE

 To switch on the scale, press the key.

 The display will show the software revision number and then

flash all the digits and symbols before counting down to zero.

This ensures all LCD segments are working. The last active

weighing unit will be displayed.

 The scale will turn off automatically to conserve battery life if

the automatic turn off parameter is set (see section 13.1.1). To

turn off the scale press the key.

 A battery symbol will be on when the internal battery needs to

be re-charged. Connect the power supply module to the rear of

the indicator and switch on the mains.

10.2 ZEROING

If the scale is less than 2% of the maximum capacity, pressing

will zero the scale. However, if the weight on the scale is

more than 2%, pressing will tare the scale. See the next

section on taring the scale.

10.3 TARING

Press the key to tare the scale. The weight that was

displayed is stored as the tare value. This value is subtracted

from the display, leaving zero on the display. The indicator “ ” will

be on.

10.4 SELECTING THE UNIT

To select the weighing unit press the key to move form one

unit to another. The weighing unit must be enabled by the users

beforehand (see section 13.1.3). If a unit is disabled it cannot be

selected by using the key.

11.0 USB INTERFACE

The scales come with a bi-directional USB interface.

Interface parameters are: USB

output of weighing data ASCII code

Selectable Baud

Selectable data bits

Selectable Parity

You should install the USB-Serial diver, and follow the diver

instruction, and then you can use the USB as a serial com.

unit which is “lb”. After all units are set, press the key to

move to the next parameter.

13.1.4 COMMUNICATION ADDRESS

The fourth parameter is for setting the ID for the USB results output.

Display will show “Add 0” (DEFAULT SET)

This parameter sets the communication address which is sent via

USB as an ID code. There are 26 options to select from “Add 0” to

“Add 25”. Set “Add 0” for no address. The numbers relate to

alphabets for example 1=A, 2=B to 25=Y.

13.1.5 SELECTION OF BAUD RATE

The fifth parameter is to select the baud rate per second which is

the speed of sending data to USB interface. Display will show “b

9600” (DEFAULT SET) There are three options: “b 2400”, “b 4800”,

“b 9600”.

13.1.6 SELECTION OF BIT RATE AND PARITY

The sixth parameter is to select the bit rate and parity used for

sending data to USB interface. Display will show “PAr 1” (DEFAULT

SET)

1. PAr 1 : 8 bits no parity

2. PAr 2 : 7 bits even parity

3. PAr 3 : 7 bits odd parity

13.1.7 SELECTION OF TRANSMISSION MODE

The seventh parameter is to select the transmission mode. Display

will show “trn 1” (DEFAULT SET). See the HOLD AND PRINTING

TABLE in section 13.1.9.

13.1.1 AUTO POWER OFF

 The first parameter is to set the auto power off function. The

display will show “Pr oFF” (DEFAULT SET).

 Press to toggle between “Pr on” and “Pr oFF”.

1. Pr on : Enables the Auto Power Off function. The power will be

turned off after 2minutes if a key has not been pressed for 2

minutes and the scale is at zero. If there is any weight on the

scale or a key is pressed, the scale will continue to work.

2. Pr oFF : Disables the Auto Power Off function. The scale will

not automatically turn off.

13.1.2 SETTING OF BACKLIGHT

The second parameter to set the backlight function. Display will

show “bL 3” (DEFAULT SET).

1. bL 1 : Off- backlight is switched off always

2. bL 2 : On- backlight is set to on always

3. bL 3 : Automatic- backlight will be off unless a weight is placed

on the pan. When the weight is removed it will stay on for 15

seconds after the scale returns to zero.

13.1.3 ENABLING OF UNITS

The third parameter is to enable or disable the weighing units so

that the user can select the enabled units during the weighing

operation. Display will show “on kg” (DEFAULT SET)

1. on kg : Enables the unit

2. off kg : Disables the unit

Press the key to confirm the selection and move to the next

Normal OutputU: (See section 13.1.7)

add: A

G/W: + 2.00

kg G/W is Gross Weight

add: A

N/W: + 1.00

kg N/W is Net weight

Continuous OutputU: (See section 13.1.7)

ASNG/W + 0.00

ASNG/W + 0.51

ASNG/W + 2.99 xx

A is communication address set by the user,

S stands for stable, N for no error G/W for

gross weight, xx for the chosen unit

Input commands format:

Z <cr> <lf> Tares the scale to display the net weight- same as pressing

H <cr> <lf>

Sets the scale to hold if the hold function is enabled. Same

as pressing the key.

N <cr> <lf> Sends the net weight to the USB interface.

G <cr> <lf> Sends the gross weight to the USB interface.

T <cr> <lf> Sends the tare weight to the USB interface.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali BBG Scala

BBG

BBG Industry 30 Manuale utente

Manuali Scala popolari di altre marche

AWS

AWS ZEO-50 Manuale utente

Gima

Gima Glass Body Fat Analyzer Manuale elenco delle parti

Seca

Seca 374 Manuale utente

TEC

TEC TEC SL59 SERIES Manuale utente

Axis

Axis B/E Series Manuale utente

Alecto

Alecto ACW-40 Manuale utente

Rice Lake

Rice Lake MSI-4260 IS Manuale utente

IKA

IKA RCT basic safety control Manuale utente

ADE

ADE M20011 Manuale utente

Duronic

Duronic KS3000 Manuale utente

Digi

Digi SM-720 Manuale utente

Cardinal

Cardinal CS Series Manuale utente

Korona

Korona Kastella Manuale utente

A&D

A&D FC-50Ki Manuale utente

BDA

BDA CAMARGUE Manuale utente

Tanita

Tanita HD-357 Manuale utente

Leifheit

Leifheit 03173 Manuale utente

Lumme

Lumme LU-1340 Manuale utente