BCP SKY2912 Manuale utente
Ver. 4 SKY2912
INSTRUCTION
MANUAL
Wall-Mounted Electric Fireplace
As shoppers, we’re always trying
to find the perfect balance between
quality & value. At BCP, we believe
we’ve achieved that. Our diverse
catalog of everyday essentials is
tailored especially to our customers
& guaranteed to hit that sweet
spot of high quality & low price.
Always.
•Please read through all instructions before mounting and using this fireplace.
•This fireplace is designed to mount onto the wall and not recessed within a wall.
•This product should be wall-mounted at least 1 ft. above the ground. A 2 ft. height is recommended.
•There should be at least 3.5 ft. clearance between this product and the ceiling.
•The wall bracket on this product should only be fit horizontally.
•The cable should only be routed to the bottom right of the heater.
•Only use this heater with an AC power supply with the correct voltage.
•Do not plug in other devices into the same circuit.
•Do not turn the appliance on until it is properly installed.
•Do not leave appliance unattended during use or when plugged in.
•Do not let children operate or go near this appliance.
•Do not let children or small pets near during mounting and installation.
•Do not operate this product if the cord or any parts of this appliance are damaged. Do not attempt to
modify the cord.
•Periodically check the cord and appliance for damage.
•Do not run cord under rugs, furniture, etc.
•Do not allow cord to hang over sharp edges or place near hot surfaces.
•Do not cover or obstruct the heater in any way.
•Do not attempt to replace the LED bulbs. Only a licensed and qualified electrician should do so.
•Repairs to this appliance should only be performed by a licensed and qualified electrician.
•Do not attempt to open the back panel unless the electricity is turned o.
•Disconnect and discontinue use of this appliance if any water damage occurs, or if the unit becomes
hot to the touch, broken, or smokes/smells like smoke.
•Do not dispose of this appliance as unsorted waste. Use special collection facilities for electrical
appliances.
NOTE: When the heat function is turned on for the first time, a slight odor may be present. This is normal
and should not occur again.
NOTICE Please retain these instructions for future reference.
| 3
SPECIFICATIONS
Power Supply
Rated Power
120 V/60 Hz
750 W/1500 W
1 PC
WALL-MOUNTING
BRACKET
1 PC
HEATER
1 PC
PARTS
ABTEMPERED GLASS
C
HARDWARE
1
5 PCS
M4 x 8mm
SCREW
M4 x 30mm
SCREW
WALL
ANCHOR
2
5 PCS
3
5 PCS
TOOLS REQUIRED
PHILLIPS
SCREWDRIVER
1 PC
REMOTE
D
DRILL,
NO.6 DRILL BIT
PENCIL
& RULER LEVELER
APPROXIMATELY
45 MIN.
ASSEMBLY
2 PERSON
ASSEMBLY
4|
2 AAA BATTERIES
+AAA -
| 5
•Mark the location where the screws will go on the wall. NOTE: Do not ax this appliance at a height
lower than 1 ft. from the floor (at least 2 ft. recommended), or higher than 3.5 ft. from the ceiling.
•Drill the holes for the screws with a No. 6 drill bit.
NOTE: It is recommended to use a level to ensure holes are drilled at an even height.
Insert five part 3 wall anchors into the drilled holes.
Attach the part A wall bracket to the wall anchors with five part 2 screws.
WALL
1
A
Ax5
2
x5
3
Carefully lift and secure the part B heater to the wall bracket, ensuring the top ledge of heater
connects with and is centered with the wall bracket.
Attach the sides of the wall bracket to the heater with two part 1 screws, one on each side.
2
WALL
B
x2
1
MOUNTING ON WALL
3
4Secure glass to the heater with three part 1 screws.
MOUNTING ON WALL
6|
Align the part C tempered glass over the front of the unit. Make sure the slots in the bracket on
the sides of the glass panel align with the lugs on the side of the heater.
Carefully lower the tempered glass onto the lugs.
BACK VIEW
BACK VIEW
x3
1
•This appliance has a safety-cut o that will engage if the fireplace overheats. The fireplace will NOT
automatically reset for safety reasons. To reset the appliance, unplug the unit for 15 minutes and then
plug it back in.
•This appliance can be controlled by the panel on the unit or the remote.
•Do not press the buttons more than once in two seconds; it takes some time for the fireplace
to respond.
HEATER/FIREPLACE OPERATION
•ON/OFF: Turn the fireplace heater on/o.
•DIMMER: Controls the brightness levels of the flames. Press to cycle through five brightness levels.
•HEAT: Press to set heat to low setting (750W), high setting (1500W), or turn o.
•TEMP: Press to set temperature from 62°F to 82°F, or turn o.
•TIMER: Press to set timer from 1 hour to 8 hours, or turn o.
•STANDBY SWITCH: Press to toggle standby on/o. This must be switched on to use the
heater/fireplace.
Digital display: Displays temperature,
heat setting, brightness level, timer
DIAGRAM
CONTROL PANEL
Control panel
LED display
ON/OFF DIMMER HEAT TEMP TIMER
Time indicator
Heat indicator
Power on
Fireplace on
| 7
8|
REMOTE CONTROL
ON/OFF
°F: Adjust temperature settings
DIMMER: Adjust dimmer settings
HEAT: Adjust heat settings
TIME: Adjust timer settings
•Install 2 AAA batteries in the remote control.
CARE AND MAINTENANCE
•Turn unit o and unplug before any maintenance. Wait at least 15 minutes after unplugging before
cleaning or maintenance.
•Use a vacuum/duster to keep vent area and heater clear of debris and dust.
•Fireplace exterior should be cleaned with a damp cloth or duster.
•Do not use abrasive cleaners or liquids.
WARNINGS REGARDING BATTERIES
•Do not mix alkaline, standard (carbon zinc) and rechargeable (nickel hydride) batteries.
•Do not mix old and new batteries.
•Non-rechargeable batteries should not be charged.
•Rechargeable batteries should be charged under adult supervision only.
•Exhausted batteries should be removed.
•The supply terminals should not be short-circuited.
•Do not put batteries next to or in a heat source (fire, electronic heating device, etc.).
•Do not hit batteries against hard objects.
•Do not submerge batteries in water.
•Batteries should be inserted with the correct polarity.
| 9
10 |
Check out more great products:
bestchoiceproducts.com
Altri manuali per SKY2912
1
Indice
Altri manuali BCP Camino da interno
