BEA CONDOR ID Manuale utente
CONDOR ID
1
4RED-GREEN RED-GREEN OFF
QUICK GUIDE
STEP 1STEP 4
WIRING
PRESETTINGS
RFID GATE SENSOR
>2.8 m
<2.8 m
12-24V
GND
COM
NO
COM
NO
NC
NC
GREEN
BROWN
WHITE
YELLOW
PINK
VIOLET
GREY
BLACK
POWER-
SUPPLY
START-
SIGNAL
STOP-
SIGNAL
P.4
P.3
At the end of the installation or
after changing the adjustment of
the sensor,it is MANDATORY to
introduce the preset value
in function of the installation
height by remote control.
FOR THIS, THE IR-FIELD
MUST BE EMPTY!
15°
30°
45°
15°
30°
45°
STEP 2
SENSOR ANGLE
p.3
G
N
I
L
I
E
C
W
A
L
L
0
SETUP
See user’s guide on the
next pages for more
detailed information. p.4
STEP 5
+
-
STEP 3
RADAR ANGLE
p.3
START STOP
2/8
EXIT
RFID GATE SENSOR
CONDOR ID
START-SIGNAL
Fasten the sensor
firmly to avoid vibrations.
Do not cover
the sensor.
Avoid moving objects
in the detection field.
Avoid HF, neon and
discharge lamps in the
detection field.
LED FLASHES
QUICKLY
LED FLASHES
SLOWLY
SETUPSTOP-SIGNAL LED OFF
Fixing screw
Radar antenna
Infrared lenses
Adjustment screw
for radar tilt angle
LED
INSTALLATION TIPS
LED-SIGNAL
DESCRIPTION
USER’S GUIDE
GREEN LED RED LED RED-GREEN LED
11
00
11
11
22
33
m
m
m
m
START STOP
+
-
3/8
By turning the screw clockwise, the detection depth decreases resp.
The detection field approaches the sensor.
By turning the screw counter clockwise, the detection depth
increases.
The angle of the radar field can be adapted by turning the adjustment screw.
Installation height: 3.2m
Field size: 8
Rejection mode: 1 (detection of pedestrians)
Installation height: 2.5m
Field size: 7
Rejection mode: 1 (detection of pedestrians)
The IR-detection field is approx.15% smaller than the zone detected by the Spotfinder.
If rejection mode 2 (detection of pallets) is selected, the radar detection field is slightly smaller.
12-24V
GND
COM
NO
COM
NO
NC
NC
GREEN
BROWN
WHITE
YELLOW
PINK
VIOLET
GREY
BLACK
POWER-
SUPPLY
START-
SIGNAL
STOP-
SIGNAL
NOT USED
NOT USED
DETECTION FIELD
WIRING
The Spotfinder is necessary to position the
detection field correctly.
The CONDOR ID should be positioned by using
the Spotfinder so that the START-line is at the
desired distance from the sensor.
Therefore the Spotfinder should be put on the
floor and turned towards the sensor. The
CONDOR ID should be adjusted until the
Spotfinder detects the first line of IR-spots.
If the adjustment screw has to be repositioned to the default position as shown above, it is mandatory to
start from the 12 o’clock position and turn counterclockwise to the 9 o’clock position.
F1
0
1
8
2
0
2
3
0
2
8
2
0
2
3
0
1
5
2
0
2
3
0
1
7
2
1
2
3
0
2
7
2
1
2
3
0
1
5
2
1
2
3
>2.8m <2.8m
0
1
7
2
0
0
4
123459
6
1
2
4/8
1.
2.
3. 1
0
Max. duration of presence detection
IR-Immunity
Detection field size
Rejection mode
Holdtime STOP-Relay
RFID-mode
Relay configuration
Installation height
Platform
Platform
Factory settings
Standard
Standard
Vestibule
Vestibule
REMOTE CONTROL
PRESETTINGS
When 2 or more sensors are installed close to each other or their detection fields overlap, alternate the frequencies
between sensors to avoid crosstalk.
Frequency 1
Frequency 1
Frequency 2
FREQUENCY ADJUSTMENT
RED-GREEN
RED-GREEN
At the end of the installation or
after changing the adjustment of the
sensor,it is MANDATORY to introduce
the preset value in function of the
installation height by remote control.
FOR THIS, THE IR-FIELD MUST BE
EMPTY!
SETUP
1
2
3
4
1
2
3
4
5
0
1
2
3
0
1
2
1
2
0
1
2
3
4
5
6
7
8
9
START STOP
?
1
2
F1
F1
?
123
456
789
0
F1 F2 ...
F1 F2 ...
?
5/8
0 ms
500 ms
1000 ms
1500 ms
active
passive
passive
active
radar + IR seperately
combined mode
combined mode + error mode
standard
platform
normal (pedestrian detection)
increased immunity (pallet detection)
low rejection
medium rejection
high rejection
0-9
factory value: 7
15 sec
30 sec
1 min
2 min
5 min
10 min
20 min
1 h
1,30 h
2 h
passive
active
passive
active
unlock
lock
value check
frequency 1
frequency 2
setup
presettings
factory settings
0
9
1 or 4
Relay configuration
Size of detection field
Rejection mode
Holdtime STOP-Relay
RFID-mode
IR-Immunity
Max. duration of
presence detection
Frequency
Factory value
REMOTE CONTROL
SETTINGS OVERVIEW
How to adjust one or more parameters?
How to check one or more values?
RED RED
RED OFF
Select parameter Set value
Xvalue
RED RED GREEN OFF
Select parameter
The number of green
flashes indicates the
value of the chosen
parameter.
6/8
RED-GREEN
RED-GREEN
RED
During setup the LED
continues to flash
quickly red-green.
The power supply is too weak.
High intensity light (discharge
lamps) disturbs the sensor.
During setup the LED
continues to flash
slowly red-green.
The sensor does not
respond to the remote
control.
The batteries in the remote
control are not installed properly
or dead.
The remote control is badly
pointed.
The sensor is not powered.
The sensor requires an access
code.
Verify or replace the batteries.
Make sure the power supply is
stable.
Change the position of the lamps.
Point the remote control towards
the sensor.
Check the power supply of the
sensor.
The sensor does not
unlock, even after
entering the access
code.
You have to enter a code or the
wrong code was entered.
(Maybe it was changed?).
Cut and restore power supply.
No code is required to unlock
during the first minute after
powering.
New access code: + + new code
Delete access code: + + 0000
LED
SYMPTOMS POSSIBLE CAUSES CORRECTIVE ACTION
TROUBLESHOOTING
RED-GREEN
Internal problem
The red and green
LED are permanently
on.
The sensor is defect and has to be
replaced.
The IR sensor does
not react.
The IR power emission is too
low according to the mounting
height.
Launch a new setup.
Make sure to step out of the
detection field before.
RED
OFF
7/8
microwave and infrared
24.175 GHz
2
<< 5mW/cm
< 20 dBm EIRP
motion and presence
green, red
12 - 24V AC +10% / -10%
12 - 24V DC +10% / - 3%
50 - 60 Hz
< 3.5W
2 relays with switch-over contact (free of potential)
60V DC / 125V AC
1A (resistive) @ 24V DC
30W (DC) / 60VA (AC)
2.5m - 3.2m
0° to 45°
-8° to +15° (relative to sensor front face)
-30°C to +60°C
IP65
Electromagnetic compatibility (EMC) according to
ABS + PC
black
7.5m
2004/108/EEC
127 mm (D) x 102 mm (B) x 96 mm (H)
400g
Technology:
Radiated frequency:
Radiated power density:
Transmitter radiated power:
Detection mode:
LED-signal:
Supply voltage:
(measured at cable end)
Mains frequency:
Power consumption:
Output:
Max. voltage:
Max. current:
Max. switching power:
Installation height:
Tilt angle sensor:
Tilt angle radar:
Temperature range:
Protection degree:
Norm conformity:
Dimensions:
Weight:
Material:
Colour:
Cable length:
Specifications are subject to change without prior notice.
TECHNICAL SPECIFICATIONS
SENSORIO A division of BEA SA - LIEGE Science Park - Allée des Noisetiers 5 - 4031 Angleur [B]
8/8
42.0627-V8 / 03.10
Indice
Altri manuali BEA Accessori
BEA
BEA FALCON DR Manuale utente
BEA
BEA IXIO-DT1 Manuale utente
BEA
BEA Falcon Manuale utente
BEA
BEA ULTIMO Manuale utente
BEA
BEA LZR-MICROSCAN1UT Manuale utente
BEA
BEA EAGLE Manuale utente
BEA
BEA PBR45 Series Manuale utente
BEA
BEA Sparrow Manuale utente
BEA
BEA IS40 Manuale utente
BEA
BEA MAGIC SWITCH CHROMA Manuale utente
BEA
BEA MAGIC SWITCH MS09 Manuale utente
BEA
BEA ACTIV8 THREE PULSE Manuale utente
BEA
BEA CONDOR Manuale utente
BEA
BEA WIZARD PLUS Manuale utente
BEA
BEA BEAMBOX Manuale utente
BEA
BEA IXIO-DT3 Manuale utente
BEA
BEA 1SAFE Manuale utente
BEA
BEA COLIBRI ONE Manuale utente
BEA
BEA SUPERSCAN-T Manuale utente
BEA
BEA LZR RS300 Manuale utente
