BEA PANTHER Series Manuale utente

75.5172.06 PANTHER SERIES 20160517 Page 1 of 4

PANTHER SERIES

75.5172.06 PANTHER SERIES 20160517 Page 1 of 4

Push plate with integrated 900

MHz wireless transmitter

(US version)

ENGLISH

DESCRIPTION

1. Hex Key

2. Housing Assembly

3. Faceplate

4. Locking Tab

5. Mounting Bracket

6. Battery Enclosure

7. Mounting Keys

8. Mounting Holes

6 INCH ROUND, 900 MHz:

10EMR61-900 - logo & text

10EMR6-900 - text only

10EMR6L-900 - logo only

4.75 INCH ROUND, 900 MHz:

10EMR4751-900 - logo & text

10EMR475-900 - text only

10EMR475L-900 - logo only

4.75 INCH SQUARE, 900 MHz:

10EMS4751-900 - logo & text

10EMS475-900 - text only

10EMS475L-900 - logo only

Page 2 of 4 75.5172.06 PANTHER SERIES 20160517

1 2

Page 2 of 4 75.5172.06 PANTHER SERIES 20160517

• The device should not be used for purposes other than its intended use. All other uses cannot be

guaranteed by the manufacturer of the sensor.

• The installer of the door system is responsible for carrying out a risk assessment and installing the sensor and

the door system in compliance with applicable national and international regulations and standards on door

safety.

• The manufacturer of the sensor cannot be held responsible for incorrect installations or inappropriate

adjustments of the sensor.

INSTALLATION

Install Mounting Bracket using at least

two (2) #8 countersunk head screws.

Any mounting holes may be used.

Observe “THIS END UP”.

Align Housing Assembly onto Mounting

Keys and slide down until Locking Tab

engages. To remove, press Locking Tab

and slide up.

Insert Faceplate into Housing Assembly

and use Hex Key to engage spring clips

on the top and bottom of Housing

Assembly. To remove, use Hex Key to

disengage spring clips.

NOTES:

1. For added security, additional screws

may be installed through Housing

Assembly and Mounting Bracket during

Step 2.

2. Ensure spring clips “click” during

Faceplate installation. It may be

necessary to rotate Faceplate for proper

alignment.

75.5172.06 PANTHER SERIES 20160517 Page 3 of 4

TROUBLESHOOTING

No activation Receiver not programmed Setup transmitter

Receiver improperly wired Verify power and activation

connection

Dead battery Replace battery

Constant activation Battery Housing screws

too tight

Loosen Battery Housing screws

Activation connected to

NC of door control

Connect to NO

Receiver set to Toggle

Mode

Set receiver to Pulse Mode

SETUP

To program the 900 MHz wireless

receiver (sold separately), please refer to

the appropriate User’s Guide:

• 900 MHz - 75.5786

900 MHz Panther series must use a

900 MHz receiver.

Remove four (4) screws on Battery

Enclosure.

• 900 MHz versions - two (2) CR2032

DO NOT OVER TIGHTEN SCREWS

DURING REASSEMBLY. THIS MAY

CAUSE CONSTANT TRANSMITTER

ACTIVATION.

BATTERY REPLACEMENT

Page 4 of 4 75.5172.06 PANTHER SERIES 20160517

FCC ID: 2ABWS-10TD900PTRI IC: 4680-10TD900PTRI

MODEL: 10EMR61-900 MODEL: 10EMR4751-900 MODEL: 10EMS4751-900

MODEL: 10EMR6-900 MODEL: 10EMR475-900 MODEL: 10EMS475-900

MODEL: 10EMR6L-900 MODEL: 10EMR475L-900 MODEL: 10EMS475L-900

Page 4 of 4 75.5172.06 PANTHER SERIES 20160517

Upon completion of the installation or service work, at a minimum, perform a daily safety check in accordance with the minimum

inspection guidelines provided by AAADM. Provide each equipment owner with an owner’s manual that includes a daily safety

checklist and contains, at a minimum, the information recommended by AAADM. Offer an information session with the equipment

owner explaining how to perform daily inspections and point out the location of power/operation switches to disable the equipment if

a compliance issue is noted. The equipment should be inspected annually in accordance with the minimum inspection guidelines. A

safety check that includes, at a minimum, the items listed on the safety information label must be performed during each service call.

If you are not an AAADM certiﬁ ed inspector, BEA strongly recommends you have an AAADM certiﬁ ed inspector perform an AAADM

inspection and place a valid inspection sticker below the safety information label prior to putting the equipment into operation.

ANSI / AAADM Compliance

TECHNICAL SPECIFICATIONS

Dimensions 6” ROUND - 6.33” diameter, 1.45” depth

4.75” ROUND - 5.12” diameter, 1.42” depth

4.75” SQUARE - 5.12” height, 5.12” width, 1.42” depth

Weight 6” ROUND - 1.2 lbs

4.75” ROUND - 1.14 lbs

4.75” SQUARE - 1.04 lbs

Material FACEPLATE - stainless steel

HOUSING - ABS plastic

Transmitter Frequency 433 MHz or 900 MHz

Power 900 MHz versions - two (2) CR2032

Mounting Surface mount only

Certiﬁcation FCC, IC

Temperature 14 °F - 131 °F (-10 °C - 55 °C)

Enclosure Rating NEMA 4

Speciﬁcations are subject to change without prior notice.

All values measured in speciﬁc conditions.

PLEASE KEEP FOR FURTHER USE - DESIGNED FOR COLOR PRINTING

©BEA|OriginalInstructions|75.5172.06PANTHERSERIES20160517

Tech Support: 1-800-407-4545 | Customer Service: 1-800-523-2462 | General Tech Questions: T[email protected] | Tech Docs: www.beasensors.com

FCC / IC

“This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.”

Changes or modiﬁcations not expressly approved by BEA Incorporated could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the

interference at his own expense.

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause

interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions

suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage

est susceptible d’en compromettre le fonctionnement.

Questo manuale è adatto per i seguenti modelli

Altri manuali BEA Ausilio alla mobilità