Beacon KV-901T Manuale utente

KV-901T & AV-901R

Installation and User’s

Manual

Version 5.01 (Date: June 19, 2012)

1. Introduction

The KV-901T/AV-901R is a solution of DVI/VGA with Audio

extension over 100Mbps Ethernet LAN. The KV-901T is

Transmitter (TX), the AV-901R is Receiver (RX). The TX connects

with PC or any source with VGA/DVI/Audio output. The RX

connects with display and speaker. Any 100M, Gigabit or Fiber

Ethernet LAN switch can be used to inter-connect the TX and RX.

They are flexible in one-to-one Unicast mode, or in one-to-

many/many-to-many Multicast mode.

1.1 Specification

Input video & resolution

Input video can be VGA or DVI-D in all standard resolutions from

640 x 480 to 1920 x 1080 @ 60Hz ~ 70Hz and the following special

resolutions 1440 x 900, 1400 x 1050, 1680 x 1050, 1360 x 768.

Output video & resolution

Output video can be VGA or DVI-F in all standard resolutions from

640 x 480 to 1920 x 1080 @ 60Hz ~ 70Hz and the following special

resolutions 1440 x 900, 1400 x 1050, 1680 x 1050, 1360 x 768.

Output frame rate

640X480@70fps, 800X600@70fps, 1024X768@60fps, 1280X1024

@30fps, 1600X1200@30fps, 720X480@60fps, 720X576@50fps,

1280X720@30fps, 1440x900@30fps, 1400x1050@30fps,

1680x1050@30fps, 1360x768@30fps, 1920X1080@25fps

Scalar support: Allows difference input and output resolution, also

support input-VGA/output DVI-D, input DVI-D/output VGA

LAN: 10/100Mbps, Auto-MDIX, Flow control.

IR Bridge: IR in/out, 38 KHz. (optional)

Remote PC Control: PS2 or USB (optional).

Audio/Microphone: 48 KHz stereo audio and microphone.

RS232 Bridge: AV-901R support remote RS232, baud 2400 ~

115200 (optional).

2. Installation Setup

2.1 Install KV-901T Transmitter

1. The DVI input of the KV-901T is [DVI-I] (VGA + DVI-D). You can

use the accessory of VGA-to-DVI cable to connect KV-901T to

PC VGA-Out. Or you can prepare a DVI-to-DVI cable to connect

KV-901T to PC DVI-Out.

2. There is a [VGA-Out] on the KV-901T for the VGA loop-out. It is

only available when the input video is DVI-A (or VGA). You can

attach a VGA monitor on this [VGA-Out] for local display.

3. Use accessory of audio cable to connect KV-901T [Line-IN] to

the PC Line-Out.

4. Use optional accessory of Mini USB-to-A cable to connect KV-

901T [Mini USB] to PC USB for keyboard/mouse remote control.

5. Use optional accessory of IR blaster cable to connect KV-901T

[IR Out] and adjust the IR blaster LED face to the IR receiver of

your Media Center PC, TV tuner card or DVD player.

6. Use CAT5e/6/7 cable to connect KV-901T [Ethernet] to the

Ethernet switch (or directly to the AV-901R). All of KV-901T and

AV-901R must be put in the same network and should not be

inter-connected with router.

7. Use the included 12V DC power adapter to connect KV-901T

[DC IN] power socket and plug the power supply to wall.

8. There is a [Status] LED and 2 RJ45 LEDs on the KV-901T, please

refer to the below table for the status of KV-901T:

[Status] LED

RJ45 LED

Status

Red

Green

Orange

System OK, network is not connected

Blink

System software trap error

Blink

System OK, network is connected

System OK, transmit rate exceeds 50Mbps

On (Orange)

LED shows as indicated when [Reset] button is

pressed, and it stays on until system reboots.

9. The [Reset] button on the KV-901T Rear panel can be used for

entering “Advance Setup Mode”, please refer to Chapter 4.

The panel diagram is shown as below:

2.2 Install AV-901R Receiver

1. The DVI output of the AV-901R is [DVI-I] (VGA + DVI-D). You

can use the accessory of VGA-to-DVI cable to connect AV-901R

to the VGA monitor. Or you can prepare a DVI-to-DVI cable to

connect AV-901R to the DVI monitor.

2. Use accessory of audio cable to connect AV-901R [Line Out] to

speaker and plug microphone into the [Mic In] port.

3. If you need remote keyboard/mouse function, plug keyboard

and mouse to the [PS2] or optional [USB]port.

4. If you need remote RS232 function, plug RS232 cable to the

[RS232] port.

5. If you need remote IR function, connects optional IR receiver

cable to the [IR extender] port and positioned the receiver to

be visible from the front of the Display.

6. Use CAT5e/6/7 cable to connect AV-901R [Ethernet] to the

Ethernet switch (or directly to the KV-901T). All of KV-901T and

AV-901R must be put in the same network and should not be

inter-connected with router.

7. Connect the included DC 5V 2A power adapter to the DC-IN and

plug the power supply to wall. To avoid damage to the AV-901R,

please use power adapter in the package.

8. There is a [Source] button on the front panel for the system

OSD operation menu. Please refer to Chapter 3 for detail.

9. There is a [Power] LED and 2 RJ45 LEDs on the AV-901R, please

refer to the below table for the status of AV-901R:

[Power] LED

[RJ45]

Status

Red

Green

Orange

Off

No Power

System OK, network is not connected

Blink

System software trap error

System OK, network is connected, but not able to link with

Transmitter

System OK, linked with Transmitter

System OK, dis-connected with Transmitter (the [Power] LED

in orange color)

System OK, but jpeg frame error due to video data lost

inevitable during transmission. Monitor screen may or may

not be OK, depending on how worse data lost is.

On (Orange)

LED shows as indicated when [Reset] button is pressed,

and it stays on until system reboots.

10. The [Reset] button on the AV-901R Rear panel can be used for

entering “Advance Setup Mode”, please refer to Chapter 4.

The AV-901R panel diagram is shown as below:

The AV-901R100 panel diagram is shown as below:

3System Menu (OSD)

2 types of OSD (On Screen Display) menu in AV-901R Receiver:

Transmitter List menu and System menu. You can enter

Transmitter List menu by pressing <Ctrl><Ctrl> hotkey. Pressing

the AV-901R [Source] button will bring you to the System menu.

3.1 Transmitter List menu

To active the Transmitter List menu, press the <Ctrl> key

twice within two seconds, you may see the OSD menu showing a

list of all KV-901T Transmitters as below.

The menu shows 4 x KV-901T are

found in the network with name of KV-

9001-PC1, …KV-9001-PC4. Navigate to

the desired Transmitter with the arrow

keys, and press <Enter>. The selected

KV-901T appears on the display, and

you can use keyboard/mouse to control the selected PC.

Press [F1] to refresh Transmitters list.

Press [F10] to change hotkey option: <CTRL>, <SHIFT>, or <ALT>.

3.2 System menu

When the AV-901R Receiver is turned on, it will search all KV-

901T available on the network and show on the System menu:

Press the [Source] button to select KV-901T, after 3 seconds the

AV-901R will connect to that KV-901T as below:

>KV-901T-0337 (192.168.168.201, 03:27)

>KV-901T-0428 (192.168.168.202, 04:28)

>VGA SYNC

>REFRESH

>KV-901T SETTING

>AV-901R OFF

>Connection Method

>EXIT

Connecting to …

After the connection is established, the AV-901R will display the

screen that is connected to that KV-901T.

3.3 Other System menu Functions

When the [source] button of AV-901R is pressed, the system

menu OSD will pop out. You can press the [source] button to

navigate other System menu functions.

3.3.1 VGA SYNC: This function is only available when the KV-

901T is connected with VGA input, when the picture shifts

from screen, use this function to auto adjust the picture.

3.3.2 REFRESH: To refresh the KV-901T Transmitters list.

3.3.3 KV-901T SETTING: Use this function to setup KV-901T:

3.3.3.1 MULTI/ONE AV-901R: To set KV-901T in Multicast mode

(for one-to-many) or Unicast mode (for one-to-one).

3.3.3.2 BANDWIDTH SETTING: KV-901T has 3 levels of bandwidth:

LOW, MID, HIGH. Please note to set LOW, it will use lower

network bandwidth and get a more efficient performance

but will come with lower image quality.

3.3.3.3 INFORMATION: Show the KV-901T/AV-901R basic

information:

3.3.4 AV-901R OFF: To disable the connection between the AV-

901R and the currently connected KV-901T. To enable the

connection, press the push button again.

>MULTI/ONE AV-901R

>BANDWDITH SETTING

>INFORMATION

>EXIT

KV-901T

VERSION aa26

SUPPORT MULTI AV-901R

BANDWIDTH LOW

DVI IN 1024 X 768

AV-901R

VERSION a901 0126

IP 192.168.168.22

VGA OUT 1024 X 768

MIC IN

INTERNAL IR

AV-901R off

>KV-901T-0337 (192.168.168.201, 03:27)

>REFRESH

>AV-901R SETTING

>AV-901R OFF

3.3.5 Connection Method: The system provides 3 connection

method:

3.3.5.1 First Available: This function sets the AV-901R to connect

to the first available KV-901T which it found first.

3.3.5.2 By Priority: This function sets the AV-901R to connect to

the KV-901T according to the

priority. You can set the 1st and

2nd priority for 2 different KV-901T.

As the following picture, there are

two sections, each has a list of all

Transmitters that are currently on the network; just press the

source button to move the highlight to the desired

Transmitter, wait a few seconds, and the settings will be

saved and restart. The prefixed “*” indicate the Transmitter

with that priority setting.

3.3.5.3 Dedicated: Set the AV-901R to connect with a dedicated

KV-901T Transmitter.

3.4 The AV-901R Setting

From the System menu, push the AV-901R [source] button

and navigate to the “>REFRESH”, push the button again during

the system is still showing “Searching KV-901T …”. The menu with

“AV-901R SETTING”will be shown as below:

Push the [source] button again to navigate to the “>AV-901R

SETTING”, it will show the following OSD menu:

>First Available

>By Priority

>Dedicated

>EXIT

> AUDIO INPUT

> IR INPUT

> Connection Method

> RETURN

3.4.1 AUDIO INPUT:

To enable/disable the microphone input function.

3.4.2 IR INPUT: There are 3 options for IR input:

IR DISABLE: Turn off the IR function.

INTERNAL IR: To set the IR receiver from internal socket.

EXTERNAL IR: To set the IR receiver from extension cable.

3.4.3 Connection Method: Please refer to 3.3.5.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Beacon Estensione

Beacon

Beacon AV-950R Manuale utente

Manuali Estensione popolari di altre marche

SY HDBT-60T Manuale utente

Appsys ProAudio

Appsys ProAudio ADX-16 Manuale utente

Atlona

Atlona RS232 Manuale utente

IDK

IDK OPF-TH1000-A Manuale utente

Enable-IT

Enable-IT 824WP Manuale utente

Worx

Worx Landroid RadioLink WA0864 Scheda tecnica

TP-Link

TP-Link TL-WA730RE Manuale utente

Camplex

Camplex CMX-HDMI-SFPL Manuale utente

SC&T

SC&T HE03-4K Manuale utente

Marmitek

Marmitek MegaView70 Manuale utente

Samsung

Samsung SCS-26UC4 Manuale utente

Foxun

Foxun SX-GES24 Manuale utente

MuxLab

MuxLab 500771 Manuale utente

foxunhd

foxunhd SX-AEX01 Manuale utente

TERK Technologies

TERK Technologies LFIRX2 Manuale utente

Devolo

Devolo Audio Extender Manuale

Edimax

Edimax EW-7438RPn V2 Manuale utente

Shinybow USA

Shinybow USA SB-6335T5 Manuale utente